Portable Projector NP600/NP500/NP400/ NP300/NP500W NP600S/NP500WS User’s Manual The projector’s model name indicated on the projector’s label is NP600, NP500, NP400, NP300, NP500W, NP600S, NP500WS, NP600G, NP500G, NP400G, NP300G, NP500WG, NP600SG, and NP500WSG respectively. All the models are referred to as NP600, NP500, NP400, NP300, NP500W, NP600S, and NP500WS throughout the user’s manual except some of the specification pages.
nd edition, February 2009 • IBM is a trademark or registered trademark of International Business Machines Corporation. • Macintosh, Mac OS X and PowerBook are trademarks of Apple Inc. registered in the U.S. and other countries. • Microsoft, Windows, Windows Vista, Internet Explorer, and PowerPoint are either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC NP600, NP500, NP400, NP300, NP500W, NP600S, and NP500WS projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
Important Information WARNING TO CALIFORNIA RESIDENTS: Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. RF Interference (for USA only) WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual.
Important Information WARNING • Do not cover the lens with the lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap due to the heat emitted from the light output. • Do not place any objects, which are easily affected by heat, in front of the projector lens. Doing so could lead to the object melting from the heat that is emitted from the light output.
Important Information • Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire. - Do not use any power cables than the supplied one. - Do not bend or tug the power cable excessively. - Do not place the power cable under the projector, or any heavy object. - Do not cover the power cable with other soft materials such as rugs. - Do not heat the power cable. - Do not handle the power plug with wet hands.
Important Information Lamp Replacement • To replace the lamp, follow all instructions provided on page 79. • Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP.] appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
Table of Contents Important Information. ...........................................................................................i 1. Introduction........................................................................................................... 1 1 What’s in the Box?.......................................................................................................... 1 Introduction to the Projector...........................................................................................
Table of Contents Turning Up or Down Volume......................................................................................... 37 7 Turning off the Projector............................................................................................... 38 After Use...................................................................................................................... 39 4. Convenient Features. ....................................................................................
1. Introduction 1 What’s in the Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector. AT ST LA TO AU CE UR SO J. AD TO AU CT LE SE EXIT CT LE SE CU FO S S CU FO M U EN ENTER NU ME ENTER CE UR SO EXIT P M LA US AT ST J.
1. Introduction Introduction to the Projector This section introduces you to your new projector and describes the features and controls. Congratulations on Your Purchase of the Projector This projector is one of the very best projectors available today. The projector enables you to project precise images up to 300 inches (110 inches on NP600S; 104 inches on NP500WS) across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, or document camera.
1. Introduction • Six picture preset modes for user adjustable picture and color settings Each picture preset mode can be customized and memorized according to your preference. • Preventing unauthorized use of the projector Enhanced smart security settings for keyword protection, cabinet control panel lock, security slot, and security chain opening to help prevent unauthorized access, adjustments and theft deterrence.
1. Introduction Comparative Table of Main Features The main features vary depending on the model as follows. Wide Panel Model NP500W Short-Throw Model NP600S Wide Panel & ShortThrow Model NP500WS Standard Wide Standard Wide XGA (1024 x 768) WXGA (1280 x 800) XGA (1024 x 768) WXGA (1280 x 800) 60"–110" 57"–104" 28–419 inches/ 0.7–10.6 m 35"–66"/ 0.9 m–1.7 m 36"–66"/0.9 m–1.
1. Introduction Part Names of the Projector Front/Top NP600/NP500/NP400/NP300/NP500W Controls (→ page 7) Security chain opening Attach an anti-theft device. The security chain opening accepts security wires or chains up to 0.18 inch/ 4.6 mm in diameter. U A TO J.
1. Introduction Rear Lamp Cover (→ page 80) F O C S U ME NU ENTER SE LE CT EXIT SO UR CE AU TO AD J. LA MP ST AT US Monaural Speaker (7W) Ventilation (inlet) / Filter Cover (→ page 76) Ventilation (outlet) Heated air is exhausted from here. Terminal Panel (→ page 8) Spacer (black rubber) To fine-adjust the height of the rear foot, remove the spacer and rotate the rear foot to the desired height.
1. Introduction Top Features 7 8 MENU SELECT 10 R TE EX IT EN 9 LAMP STATUS 12 1. SOURCE AUTO ADJ. 5 6 (POWER) Button (→page 27, 38) 2. POWER Indicator (→page 26, 38, 82) 3. STATUS Indicator (→page 82) 4. LAMP Indicator (→page 79, 82) 5. SOURCE Button (→page 29) 6. AUTO ADJ. Button (→page 37) 7. MENU Button (→page 51) 8. SELECT / Volume Buttons / Keystone Buttons (→page 34, 37) 9. ENTER Button (→page 51) 10.
1. Introduction Terminal Panel Features 6 3 8 2 1 3 5 4 7 1. COMPUTER 1 IN/ Component Input Connector (Mini D-Sub 15 Pin) (→page 17, 20, 22) 2. COMPUTER 2 (DVI-I) IN Connector (29 Pin) (HDCP compatible) (→page 19, 20) 3. AUDIO IN Mini Jack (Stereo Mini) (→page 17, 19, 22) 4. AUDIO OUT Mini Jack (Stereo Mini) (→page 21) 5. MONITOR OUT (COMP 1) Connector (Mini D-Sub 15 Pin) (→page 21) 6. S-VIDEO IN Connector (Mini DIN 4 Pin) (→page 23) 7. VIDEO IN Connector (RCA) (→page 23) 8.
1. Introduction Part Names of the Remote Control 1 OFF 3 ON 2 POWER MAGNIFY PIC-MUTE PAGE UP 4 6 DOWN 7 MENU 9 ENTER 11 13 14 19 17 5 8 EXIT L-CLICK R-CLICK MOUSE VIDEO COMPUTER COMPUTER AUTO ADJ. 1 S-VIDEO LAMP MODE 2 VOLUME ASPECT HELP PICTURE FREEZE 10 12 16 15 18 21 22 20 12. MOUSE R-CLICK Button* (→ page 45, 46) 1. Infrared Transmitter (→ page 10) 13. VIDEO Button (→ page 29) 2. POWER ON Button (→ page 27) 14. S-VIDEO Button (→ page 29) 3.
1. Introduction Battery Installation 1 Press firmly and slide the battery cover off. 2 Install new batteries (AAA). En- 3 Slip the cover back over the bat- sure that you have the batteries’ polarity (+/–) aligned correctly. teries until it snaps into place. Do not mix different types of batteries or new and old batteries. Remote Control Precautions • • • • • • • • Handle the remote control carefully. If the remote control gets wet, wipe it dry immediately. Avoid excessive heat and humidity.
2. Installation and Connections This section describes how to set up your projector and how to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: z Set up a screen and the projector. x Connect your computer or video equipment to the projector. (→ page 17, 19, 20, 21, 22, 23, 24) US FOC c Connect the supplied power cable. (→ page 25) MENU CT SELE ENTER EXIT CE SOUR S STATU LAMP ADJ.
2. Installation and Connections [NP500W] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 21" (0.53 m) measured diagonally when the projector is roughly 28 inches (0.7 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 384 inches (9.7 m) from the wall or screen. Screen Size (Unit: cm/inch) 646.2(W)�403.9(H) / 254(W)�159(H) 30 516.9(W)�323.1(H) / 204(W)�127(H) 430.8(W)�269.
2. Installation and Connections [NP600S] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 60" (1.52m) measured diagonally when the projector is roughly 35 inches (0.9 m) from the wall or screen. The largest the image can be is 110" (2.8 m) when the projector is about 66 inches (1.7 m) from the wall or screen. Screen Size (Unit: cm/inch) 223.5(W)�167.6(H)/88(W)�66(H) 11 10 0" 182.9(W)�137.2(H)/72(W)�54(H) 162.6(W)�121.
2. Installation and Connections [NP500WS] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 57" (1.45m) measured diagonally when the projector is roughly 36 inches (0.9 m) from the wall or screen. The largest the image can be is 104" (2.6m) when the projector is about 66 inches (1.7 m) from the wall or screen. Screen Size (Unit: cm/inch) 224.0(W)�140.0(H)/88(W)�55(H) 4" 10 0" 193.9(W)�121.2(H)/76(W)�48(H) 187.4(W)�117.
2. Installation and Connections Throw Distance and Screen Size The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
2. Installation and Connections Distance Chart [NP600S/NP500WS] B = Vertical distance between lens center and screen center C = Throw distance D = Vertical distance between lens center and screen bottom (top of screen for ceiling application) α = Throw angle C Screen center B Lens center α D Screen bottom NOTE: The values in the tables are design values and may vary.
2. Installation and Connections Making Connections NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. * If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software.
2. Installation and Connections • Select the source name for its appropriate input connector after turning on the projector. Input connector SOURCE button on the projector cabinet COMPUTER 1 IN COMPUTER1 COMPUTER 2(DVI-I)IN COMPUTER 2(DIGITAL) or COMPUTER 2(ANALOG) Button on the remote control (COMPUTER 1) (COMPUTER 2) ↓ (Toggle) (COMPUTER 2) NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher.
2. Installation and Connections When Viewing a DVI Digital Signal To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu before turning on your PC. Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC.
2. Installation and Connections Using Two Analog COMPUTER Inputs Simultaneously If you need to use two analog COMPUTER inputs simultaneously, connect a VGA signal cable as shown below.
2. Installation and Connections Connecting an External Monitor AUDIO OUT MONITOR OUT (COMP 1) VGA signal cable (not supplied) VGA signal cable (supplied) AUDIO IN PHONE You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer analog image you’re projecting. NOTE: • Daisy chain connection is not possible. • When audio equipment is connected, the projector speaker is disabled.
2. Installation and Connections Connecting Your DVD Player with Component Output COMPUTER 1 IN AUDIO IN 15-pin - to - RCA (female) 3 cable adapter (ADP-CV1E) Audio Equipment Component video RCA3 cable (not supplied) AUDIO IN L R DVD player L R Y Cb Cr Audio cable (not supplied) AUDIO OUT Component A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS(1)] → [SIGNAL SELECT] → [COMPUTER1], and then place a check mark in the Component radio button.
2. Installation and Connections Connecting Your VCR S-VIDEO IN AUDIO IN VIDEO IN S-Video cable (not supplied) Audio cable (not supplied) Video cable (not supplied) Audio equipment VCR L R AUDIO OUT VIDEO S-VIDEO AUDIO IN VIDEO OUT L R Audio cable (not supplied) • Select the source name for its appropriate input connector after turning on the projector.
2. Installation and Connections Connecting to a Network The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a LAN. To use a LAN connection, you are required to assign an IP address to the projector on the [PROJECTOR NETWORK SETTINGS] screen of the web browser on your computer. For setting, see page 47, 48, 49.
2. Installation and Connections Connecting the Supplied Power Cable Connect the supplied power cable to the projector. First connect the supplied power cable’s two-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the wall outlet. F O U C S ME ENTER SE NU LE CT LAMP EXIT SO UR CE AU TO AD STATUS SOURCE J. AUTO ADJ. LA STA MP TU S To wall outlet ← Make sure that the prongs are fully inserted into both the AC IN and the wall outlet.
3. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. Turning on the Projector NOTE: • The projector has two power switches: a main power switch and a (POWER) button (POWER ON and OFF on the remote control). • When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off () position. Failure to do so may cause damage to the projector. 1.
3. Projecting an Image (Basic Operation) 3. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control for 1 second. LAMP STATUS SOURCE The POWER indicator will turn to green and the projector will become ready to use. TIP: • When the STATUS indicator lights orange, it means that the [CONTROL PANEL LOCK] is turned on. (→ page 67) • When the message “Projector is locked! Enter your password.” is displayed, it means that the [SECURITY] is turned on.
3. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 21 menu languages. To select a menu language, follow these steps: 1. Use the SELECT , H, F or E button to select one of the 21 languages from the menu. OFF ON POWER MENU MAGNIFY PIC-MUTE PAGE UP DOWN SELECT MENU EX I T R TE EN ENTER EXIT OFF ON POWER 2.
3. Projecting an Image (Basic Operation) Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Selecting from Source List MENU SELECT R EX IT TE EN Press and quickly release the SOURCE button on the projector cabinet to display the Source list.
3. Projecting an Image (Basic Operation) Adjusting the Picture Size and Position Use the adjustable tilt foot, the zoom function or the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the throw angle (the height of an image) [Tilt foot] (→ page 31) Adjusting the left and right tilt of an image [Rear foot] (→ page 31) FOC US FOC US MENU SELECT ENTER MENU ENTER SELECT EXIT SOURC EXIT E AUTOA SOURC DJ. E AUTOA DJ.
3. Projecting an Image (Basic Operation) Adjust the Tilt Foot 1. Lift the front edge of the projector. P M SO UR CE AU LA J. AD TO AT ST US 1 CAUTION: U EN M ENTER CT LE SE EXIT FO S CU Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can become heated while the projector is turned on and during its cool down period after it is turned off. 2 2. Push up and hold the Adjustable Tilt Foot Lever on the front of the projector to extend the adjustable tilt foot.
3. Projecting an Image (Basic Operation) Zoom S P M LA S O C R U E U A A TO J. D TU TA S [NP600/NP500/NP400/NP300/NP500W] Use the ZOOM lever to adjust the image size on the screen. T C LE E S FO C S U M E U N ENTER EXIT Zoom Lever FOCUS [NP600S/NP500WS] The image size can be adjusted electronically from the menu. To do so, follow the steps below. 1. Press the MENU button. The menu will be displayed. 2. Press the SELECT button to select [SETUP] and press the ENTER button.
3. Projecting an Image (Basic Operation) 4. Use the SELECT or button to adjust the image size. 5. After completing adjustment, press the EXIT button three times. The menu will be closed. Focus S P M LA O S C R U E U A A TO J. D TU TA S [NP600/NP500/NP400/NP300/NP500W] Use the FOCUS ring to obtain the best focus. Focus Ring T C LE E S FO C S U M E U N ENTER EXIT FOCUS TU STA J. M LA CE UR SO TO AU AD P S [NP600S/NP500WS] Use the FOCUS lever to obtain the best focus.
3. Projecting an Image (Basic Operation) Correcting Keystone Distortion Correcting Keystone Distortion If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following steps to correct keystone distortion NOTE: • The Keystone correction can cause an image to be slightly blurred because the correction is made electronically. • The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection. Adjusting with buttons on the cabinet 1.
3. Projecting an Image (Basic Operation) Adjusting with the Remote Control 1. Press the MENU button. The menu will be displayed. 2. Press the SELECT button to select [SETUP] and press the ENTER button. The [GENERAL] screen will be displayed. 3. Press the SELECT button to select [KEYSTONE]. 4. Press the SELECT or button. Adjust so that the image is rectangular. 5. Press the MENU button. The menu will be closed.
3. Projecting an Image (Basic Operation) Adjusting with the Auto Keystone Function The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special operation required. Just put the projector on a flat surface. TIP: Even when the menu setting for [AUTO KEYSTONE] is turned on, [KEYSTONE] can be adjusted manually. To turn on [AUTO KEYSTONE], proceed the following steps. 1. Press the MENU button The menu will be displayed. 2.
3. Projecting an Image (Basic Operation) Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust Optimizing a computer image automatically. Press the AUTO ADJ. button to optimize a computer image automatically. This adjustment may be necessary when you connect your computer for the first time. [Poor picture] MENU L-CLICK R-CLICK VIDEO COMPUTER AUTO ADJ.
3. Projecting an Image (Basic Operation) 7 Turning off the Projector To turn off the projector: MENU OFF ON POWER MAGNIFY PIC-MUTE SELECT PAGE UP DOWN R EX I T TE EN 1. First, press the (POWER) button on the projector cabinet or the POWER OFF button on the remote control. The [POWER OFF / ARE YOU SURE?] message will appear. MENU LAMP STATUS SOURCE 2. Secondly, press the ENTER button or press the (POWER) or the POWER OFF button again. ENTER AUTO ADJ.
3. Projecting an Image (Basic Operation) After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cable. 2. Disconnect any other cables. 3. Retract adjustable tilt foot if extended. 4. Cover the lens with the lens cap. 5. Put the projector and accessories in the supplied soft case. Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from damage. NOTE: The NP600S and the NP500WS do not come with a soft case.
4. Convenient Features 1 Turning off the Image and Sound Press the PIC-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. OFF ON POWER MAGNIFY PIC-MUTE PAGE UP SELECT NOTE: • Even though the image is turned off, the menu still remains on the screen. • Sound from the AUDIO OUT jack (Stereo mini) can be turned off. 2 Freezing a Picture DOWN MENU ENTER EXIT L-CLICK R-CLICK VIDEO COMPUTER AUTO ADJ.
4. Convenient Features 2. Press the SELECT button. The area of the magnified image will be moved 3. Press the MAGNIFY (-) button. OFF Each time the MAGNIFY (-) button is pressed, the image is reduced. ON POWER MAGNIFY PIC-MUTE PAGE UP NOTE: • The image will be enlarged or reduced at the center of the screen. • Displaying the menu will cancel the current magnification.
4. Convenient Features Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu. To enable the Security function: 1. Press the MENU button.
4. Convenient Features 7. Type in the same combination of SELECT buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press and hold the POWER button for about 1 second. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button. 3.
4. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The KEYWORD CONFIRMATION screen will be displayed. 4. Type in your keyword and press the ENTER button. When the correct keyword is entered, the SECURITY function will be disabled. NOTE: If you forget your keyword, contact your dealer.
4. Convenient Features Using the Optional Remote Mouse Receiver (NP01MR) The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations. Connecting the remote mouse receiver to your computer If you wish to use the remote mouse function, connect the mouse receiver and computer. The mouse receiver can be connected directly to the computer’s USB port (type A).
4. Convenient Features Operating your computer’s mouse from the remote control You can operate your computer’s mouse from the remote control. PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer. SELECT Buttons: moves the mouse cursor on your computer. MOUSE L-CLICK Button: works as the mouse left button. MOUSE R-CLICK Button: works as the mouse right button.
4. Convenient Features 7 Network Setting by Using an HTTP Browser Overview Connecting the projector to a network allows the Alert Mail setting (→ page 49) and the projector control from a computer via the network. To perform the projector control from a web browser, you must have an exclusive application installed on your computer. The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser by using an HTTP server function.
4. Convenient Features Network Settings http:// /index.html DHCP...................................Enabling this option automatically assigns an IP address to the projector from your DHCP server. Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator. NOTE: The IP address of the projector is required to change the network setting. The IP address will not be displayed on the projector’s menu.
4. Convenient Features Alert Mail Setting http:// /lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when the projector lamp has reached the end of its usable life or an error occurs in the projector. HOST NAME ............................. Type in the hostname of the network connected to the projector. Up to 60 alphanumeric characters can be used.
4. Convenient Features 8 Using the VGA Signal Cable to Operate the Projector (Virtual Remote) Overview The projector supports DDC/CI (Display Data Channel Command Interface) that is a standard interface for bidirectional communication between display/projector and computer. The optional utility software “Virtual Remote Tool” designed exclusively for our projector is required to use DDC/CI. Check with our website. http://www.nec-display.com/dl/en/index.
5. Using On-Screen Menu Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, , in the bottom show available buttons for your operation. 2. Press the SELECT buttons on the remote control or the projector cabinet to display the submenu. 3.
5. Using On-Screen Menu 2 Menu Elements Tab Slide bar Solid triangle Available buttons Source Highlight Radio button High Altitude symbol Thermometer symbol Key Lock symbol Off Timer remaining time Menu windows or dialog boxes typically have the following elements: Highlight..............................Indicates the selected menu or item. Solid triangle.......................Indicates further choices are available. A highlighted triangle indicates the item is active. Tab............................
5. Using On-Screen Menu 3 List of Menu Items Some menu items are not available depending on the input source.
5. Using On-Screen Menu DESKTOP FRONT OFF OFF 19200bps ORIENTATION INSTALLATION CONTROL PANEL LOCK SECURITY COMMUNICATION SPEED CONTROL ID CONTROL ID NUMBER CONTROL ID AUTO ADJUST FAN MODE COMPUTER1 SIGNAL SELECT SETUP OPTIONS(1) COMPUTER2 (ANALOG) VIDEO INFO.
5. Using On-Screen Menu 4 Menu Descriptions & Functions [SOURCE] COMPUTER1 Selects the computer connected to your COMPUTER 1 IN input connector. NOTE: • When the component input signal is connected to the COMPUTER 1 IN connector, select [COMPUTER1]. • The projector will determine if the input signal is RGB or component signal. COMPUTER2 (DIGITAL & ANALOG) Selects the computer connected to your COMPUTER 2 IN (DVI-I) connector.
5. Using On-Screen Menu 5 Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are six factory presets optimized for various types of images. You can also use [DETAIL SETTINGS] to set user adjustable settings to customize each gamma or color. Your settings can be stored in [PRESET 1] to [PRESET 6]. HIGH-BRIGHT.........
5. Using On-Screen Menu [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 6]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT......... Recommended for use in a brightly lit room. PRESENTATION...... Recommended for making a presentation using a PowerPoint file. VIDEO..................... Recommended for typical TV program viewing. MOVIE..................
5. Using On-Screen Menu [RESET] The settings and adjustments for [PICTURE] will be returned to the factory settings with the exception of the following; Preset numbers and [REFERENCE] within the [PRESET] screen. The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently selected will not be reset. [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK....................
5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency, its adjustments will be called up and applied.
5. Using On-Screen Menu Selecting Aspect Ratio [ASPECT RATIO] The term “aspect ratio” refers to the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio. • This table shows typical resolutions and aspect ratios that most computers support.
5. Using On-Screen Menu Sample image when the appropriate aspect ratio is automatically determined NP600/NP500/NP400/NP300/NP600S [Computer signal] Aspect ratio of incoming signal 4:3 5:4 4:3 Letterbox 16:9 15:9 16:10 Sample image when the appropriate aspect ratio is automatically determined [Video signal] Aspect ratio of incoming signal Sample image when the aspect ratio is automatically determined Squeeze NOTE: To display a squeezed signal properly, select [16:9] or [WIDE ZOOM].
5. Using On-Screen Menu Adjusting the Vertical Position of Image [POSITION] (not available on NP500W/NP500WS) (only when [16:9], [15:9], or [16:10] is selected for [ASPECT RATIO]) When [16:9], [15:9], or [16:10] is selected in [ASPECT RATIO], the image is displayed with black borders on the top and bottom. You can adjust the vertical position from the top to the bottom of the black area.
5. Using On-Screen Menu 6 Menu Descriptions & Functions [SETUP] [GENERAL] [NP600/NP500/NP400/NP300/NP500W] [NP600S/NP500WS] Using Digital Zoom [DIGITAL ZOOM] (NP600S/NP500WS) This feature allows you to electronically fine adjust the image size on the screen. Use or button to large or reduce the projected image. TIP: To adjust the projected image size roughly, move the projector away or closer to the screen. (→ page 30). To fine adjust the zoom, use the [DIGITAL ZOOM] function.
5. Using On-Screen Menu Using the Wall Color Correction [WALL COLOR] This function allows for quick adaptive color correction in applications where the screen material is not white. NOTE: Selecting [WHITEBOARD] reduces lamp brightness. Setting Lamp Mode to Normal or Eco [LAMP MODE] This feature enables you to select two brightness modes of the lamp: NORMAL and ECO modes. The lamp life can be extended by using the ECO mode. Selecting ECO mode decreases fan noise when compared to NORMAL mode.
5. Using On-Screen Menu Setting Closed Caption [CLOSED CAPTION] This option sets several closed caption modes that allow text to be superimposed on the projected image of Video or S-Video. OFF......................... This exits the closed caption mode. CAPTION 1-4.......... Text is superimposed. TEXT 1-4................. Text is displayed. NOTE: • The closed caption is not available under the following conditions: - when messages or menus are displayed. - when an image is magnified, frozen, or muted.
5. Using On-Screen Menu Selecting Interval Time for Filter Message [FILTER MESSAGE] This option allows you to select the time preference between displaying the message for cleaning the filters. Clean the filter when you get the message “PLEASE CLEAN FILTER.” (→page 76) Five options are available: OFF, 100[H], 200[H], 500[H], 1000[H] The default setting is 500[H]. NOTE: Your setting will not be affected even when [RESET] is done from the menu.
5. Using On-Screen Menu Disabling the Cabinet Buttons [CONTROL PANEL LOCK] This option turns on or off the CONTROL PANEL LOCK function. NOTE: • This CONTROL PANEL LOCK does not affect the remote control functions. • When the control panel is locked, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will change the setting to [OFF]. TIP: When the [CONTROL PANEL LOCK] is turned on, a key lock icon [ ] will be displayed at the bottom right of the menu.
5. Using On-Screen Menu Setting ID to the Projector [CONTROL ID] (Available only when the optional remote control NP02RC is used) You can operate multiple projectors separately and independently with the single remote control that has the CONTROL ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together using the single remote control. To do so, you have to assign an ID number to each projector. CONTROL ID NUMBER........
5. Using On-Screen Menu [OPTIONS(1)] Setting Auto Adjust [AUTO ADJUST] This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for noise and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE]. OFF......................... The computer signal will not be automatically adjusted. You can manually optimize the computer signal. NORMAL................. Default setting. The computer signal will be automatically adjusted.
5. Using On-Screen Menu Selecting Signal Format [SIGNAL SELECT] [COMPUTER1], [COMPUTER2(ANALOG)] Allows you to choose [COMPUTER1], or [COMPUTER2(ANALOG)] for an RGB source such as a computer, or [COMPONENT] for a component video source such as a DVD player. Normally select [RGB/COMPONENT] and the projector automatically detects a component signal. However there may be some component signals that the projector is unable to detect. If this is the case, select [COMPONENT].
5. Using On-Screen Menu [OPTIONS(2)] Using Off Timer [OFF TIMER] 1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00. 2. Press the ENTER button on the remote control. 3. The remaining time starts counting down. 4. The projector will turn off after the countdown is complete. NOTE: • To cancel the preset time, set [OFF] for the preset time or turn off the power.
5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1)] When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1 IN input will power on the projector and simultaneously project the computer’s image. This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet to power on the projector.
5. Using On-Screen Menu 7 Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage. This item has four pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE REMAINING] (%)* [LAMP HOURS USED] (H) [FILTER HOURS USED] (H) * The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of lamp usage.
5.
5. Using On-Screen Menu 8 Menu Descriptions & Functions [RESET] Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels.
6. Maintenance This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp. Cleaning or Replacing the Filters The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter is dirty or clogged, your projector may overheat. NOTE: The message for filter cleaning will be displayed for one minute after the projector is turned on or off.
6. Maintenance 3. Reinstall the new filter cover (2 locations). LA M ST P AT US AU TO AD J. EXIT SE LE CT M EN U FO C U S • Insert the filter cover until you feel click. SO UR CE ENTER 4. Clear the filter hours used. To reset the filter usage time, from the menu, select [RESET] → [CLEAR FILTER HOURS]. (→page 75 for resetting the filter usage time.) NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane.
6. Maintenance 2 Cleaning the Cabinet and the Lens 1. Turn off the projector before cleaning. 2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner. FO U C S ME NU ENTER SEL ECT EXIT SO UR CE AU TOA DJ. LAM P STA TUS Vacuum the ventilation inlet of the cabinet. Note on Cleaning the Lens (NP600/NP500/NP400/NP300/NP500W) P M R U SO E C A TO AU LA J.
6. Maintenance Replacing the Lamp When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red. Even though the lamp may still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter. (→ page 75) CAUTION • DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot.
6. Maintenance 1. Remove the lamp cover. (1) Loosen the lamp cover screw • The lamp cover screw is not removable. (2) Push and slide the lamp cover off. U C FO U C FO S S ME ME NU NU SE LE CT ENTER ENTER SE LE CT EXIT EXIT SO SO UR CE UR CE AU TO AD J. AU TO AD J. LA MP ST AT US LA MP ST AT US 2. Remove the lamp housing. (1) Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. • The two screws are not removable.
6. Maintenance 3. Install a new lamp housing. (1) Insert a new lamp housing until the lamp housing is plugged into the socket. CAUTION Do not use a lamp other than the NEC replacement lamp NP07LP. Order this from your NEC dealer. (2) Push the top center of the lamp housing to secure it. (3) Secure it in place with the two screws. • Be sure to tighten the screws. U C FO FO C S S U ME ME NU ENTER ENTER SE LE CT NU SE LE CT EXIT EXIT SO UR SO UR CE CE AU TO AD J. AU TO AD J.
7. Appendix Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages Power Indicator Indicator Condition Off Blinking light Note – 0.5 sec On, 0.5 sec Off The projector is getting ready to turn on. Wait for a moment. 2.5 sec On, 0.5 sec Off Off Timer is enabled. – 0.5 sec On, 0.5 sec Off The projector is cooling down. Wait for a moment. Green The projector is turned on. – Orange The projector is in Standby.
7. Appendix Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 82.) Problem Check These Items Does not turn on or shut down • Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on. (→ pages 25 and 38) • Ensure that the lamp cover is installed correctly. (→ page 81) • Check to see if the projector has overheated.
7. Appendix If there is no picture, or the picture is not displayed correctly. • Power on process for the projector and the PC. Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information.
7. Appendix Specifications This section provides technical information about projector’s performance. Model Number Optical LCD Panel Resolution Lens Lamp Light Output*2*3 Contrast Ratio*3 (full white: full black) Image Size (Diagonal) Projection Distance Projection Angle NP600/NP500/NP400/NP300/NP500W NP600/NP500/NP400/NP300 NP600/NP500: 0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3) NP400/NP300: 0.63 inch LCD (Aspect Ratio 4:3) 1024 2 768 pixels*1 Manual zoom and focus Zoom Ratio= 1–1.2 F1.
7. Appendix *5 An image with higher or lower resolution than the projector’s native resolution (NP600/NP500/NP400/ NP300: 1024 2 768 / NP500W: 1280 2 800) will be displayed with Advanced AccuBlend. Power Requirement Input Current Power Consumption Mechanical Installation Dimensions Weight Environmental Considerations Regulations NP600/NP500/NP400/NP300: 100–240V AC, 50/60Hz NP600G/NP500G/NP400G/NP300G: 200–240V AC, 50/60Hz NP600: 3.8–1.5A NP500/NP400/NP300: 3.5–1.4A NP600G: 1.
7. Appendix Model Number Optical LCD Panel Resolution Lens Lamp Light Output*2*3 Contrast Ratio*3 (full white: full black) Image Size (Diagonal) Projection Distance Projection Angle NP600S/NP500WS NP600S NP500WS 0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3) 1024 2 768 pixels*1 Fixed zoom and manual focus Digital Zoom Ratio= 1.2 F2.3 f= 9.7 mm 230W AC (170W in ECO Mode) 2600 lumens (approx. 70% in ECO Mode) 600:1 0.
7. Appendix Mechanical Installation Orientation Dimensions Weight Environmental Considerations Regulations Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear 12.1"(W) 2 5.4"(H) 2 11.9"(D)/308 mm(W) 2 136 mm(H) 2 301 mm(D) (not including protrusions) 7.28 lbs/3.
7. Appendix Cabinet Dimensions NP600/NP500/NP400/NP300/NP500W SOURCE AUTO ADJ. STATUS R TE EN LAMP EX IT SELECT 263 (10.4") MENU FOCUS Lens center 308 (12.1") 78 (3.1") 76 (3.0") 55.3 (2.2") 108.5 (4.
7. Appendix NP600S/NP500WS SOURCE AUTO ADJ. STATUS R TE EN LAMP IT EX SELECT 301.5 (11.9") MENU FOCUS Lens center 308 (12.1") 76 (3") 143.2 (5.6") 78 (3.1") 75.
7. Appendix Pin Assignments of D-Sub COMPUTER Input Connector Mini D-Sub 15 Pin Connector 6 11 12 13 14 15 7 8 9 10 1 2 3 4 5 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No.
7.
7.
7. Appendix Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently. * Print this page and the next page for your check.
7. Appendix In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Installation environment Model number: Screen size: Serial No.
7. Appendix TravelCare Guide 6) Problems or damage caused by expendable supplies or devices connected to the product other than those designated by NEC. TravelCare - a service for international travelers 7) Problems caused by natural consumption, wear or deterioration of parts under normal usage conditions. This product is eligible for “TravelCare”, NEC’s unique international warranty. Please note that TravelCare coverage differs in part from coverage under the warranty included with the product.
7. Appendix Western Australia; Perth 45 Sarich Court Osborne Park WA 6017 Telephone 131 632 WEB Address: NEC Corporation of Malaysia Sdn. Bhd. Address: 33rd Floor, Menara TA One, 22, Jalan P. Ramlee, 50250 Kuala Lumpur, Malaysia Telephone: +6 03 2178 3600 (ISDN) Fax Line: +6 03 2178 3789 Email Address: necare@nsm.nec.co.jp WEB Address: http://www.necarecenter.com http://www.nec.com.
7. Appendix Date: / / P-1/ , , TO: NEC or NEC’s Authorized Service Station: FM: (Company & Name with signature) Dear Sir (s), I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your following conditions, and also the Service fee will be charged to my credit card account, if I don’t return the Loan units within the specified period. I also confirm following information is correct. Regards.
7. Appendix Condition of your TravelCare Service Program 5. Loan Service Charges and Conditions: Upon acceptance of this NEC Projector, Customer agrees to assume liability for this loan unit. Enduser is requested to understand following condition of TravelCare Service Program and complete the necessary information on the application sheet. The current cost of use of this loan unit is US$200 for 12 calendar days.
© NEC Display Solutions, Ltd.
