====================================================================== Control Commands for NEC Projector (Basic) Rev 5.16.11a Copyright (C) NEC Display Solutions, Ltd. 2002-2011 ---------------------------------------------------------------------Updated on May 16, 2011 ---------------------------------------------------------------------This file contains information about NEC projector control commands.
====================================================================== Contents 1. Projector Control 2. Connection Method 3. Interface Conditions 4. List of Commands 5. Command Descriptions 6. Table of Response Error Codes ====================================================================== 1.
(!2) Only the M300 series is compatible. [P350X/P350W/P420X Series] STANDBY MODE: "POWER-SAVING" Control Command POWER ON Yes: Supported No: Not supported Serial Wired Wireless port LAN port LAN unit Yes No No ==================================================================== 3.
(1) (2) (3-1) (3-2) (3-3) (3-4) Serial Port USB Port Wired LAN Card Wireless LAN Card Wired LAN Port Wireless LAN Port GT5000/GT6000 Yes Yes Yes Yes Yes No GT1150/GT2150 Yes No Yes Yes Yes No HT410/HT510 Yes No No No No No HT1000/HT1100 Yes No No No No No LT180 Yes No No No No No LT25/LT30/LT35 Yes No No No No No LT220/LT240/LT260 Yes No Yes Yes No No LT240K/LT260K Yes Yes Yes Yes No No LT245/LT265/LT280/LT380 Yes No No Yes Yes No MT
Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode". The projector cannot use the control commands in the power-saving condition, but the following model can use some control commands.
The PC CONTROL connector is a D-SUB 9-pin connector. 1 2 3 4 5 6 7 8 9 To TxD of PC To RxD of PC To GND of PC To CTS of PC To RTS of PC ==================================================================== 4. Communication Frame ---------------------------------------------------------------------On the LT/MT/SX/GT series projectors communication is done in a frame composed of header, data, and checksum.
Command : This sets an identification data assigned to each command to send it. ( See each command description.) Response : This returns the 6th bit of received ID1 as HIGH. For ACK it sends the 8th bit back as LOW (recognized); for NAK it sends the 8th bit back as HIGH (not recognized). * ID2: (8 Bit) This is an identification data assigned to each command. Command : This sets an identification data assigned to each command to send it. ( See each command description.
basis Broadcast notification is recommended. * When the controller is connected with multiple projectors To control a certain projector, use "individual notification". For all others "broadcast notification" is recommended. Response : This returns the model code for a projector received regardless of individual notification or broadcast notification.
4-2. Data portion of response ********************************************************************** For ACK This returns ACK without adding data portion to the command that does not request data. This returns ACK with adding data to the data portion for the command that requests data. For NAK This adds a cause of not accepting the command to data portion to return it.
00H : Start is not requested 01H : Cannot process due to storing 02H : Exceeds the total number of blocks required at the time of start 03H : The block number of transferred data is not consecutive. USB connection ---------------------------------------------------------------------This conforms to the USB1.1 standard. Transfer speed: All speeds (supported) Endpoint: Control transfer Endpoint 0 Device class: HID class (Ver1.1) USB1.1 Standard: Universal Serial Bus Specification Revision 1.
==================================================================== 4. List of Commands ---------------------------------------------------------------------* Example for command ---------------------------------------------------------------------Command name Example ---------------------------------------------------------------------006. RUNNING SENSE 007. COMMON DATA REQUEST 009. ERROR STATUS REQUEST 015. POWER ON 016. POWER OFF 018. INPUT SW CHANGE 020. PICTURE MUTE ON 021. PICTURE MUTE OFF 022.
07 : GT5000 08 : LT240K/LT260K 09 : GT6000 10 : HT1100 11 : VT770 12: HT410/HT510 (HT10 Series) 13 : LT245/LT265 14 : LT280/LT380 15 : LT180 16 : VT37/VT47/VT470/VT57/VT570/VT575/VT670/VT676 (VT70 series) 17 : VT48/VT480/VT580 (VT80 Series) 18 : NP1000/NP2000 (NP1000 Series) 19 : NP1150/NP2150/NP3150/NP3151W (3150 Series) 20 : LT25/LT30/LT35 (LT30 Series) 21 : NP40/NP50/NP60 (NP60 Series) 22 : VT49/VT490/VT590/VT595/VT695 (VT90 Series) 23 : VT700 24: NP4000/NP4001 (NP4000 Series) 25: NP905/NP901W/VT800 (NP9
Meaning of Symbols -------------------------------------------------------------------* Supported ! Is available depending on model's version - Not Supported Availability by Model (CURRENT MODELS) Command Name 006. RUNNING SENSE 007. COMMON DATA REQUEST 009. ERROR STATUS REQUEST 015. POWER ON 016. POWER OFF 018. INPUT SW CHANGE 020. PICTURE MUTE ON 021. PICTURE MUTE OFF 022. SOUND MUTE ON 023. SOUND MUTE OFF 024. ONSCREEN MUTE ON 025. ONSCREEN MUTE OFF 030. GAIN ADJUST 030-2.
Availability by Model (LEGACY MODELS) Command Name 006. RUNNING SENSE 007. COMMON DATA REQUEST 009. ERROR STATUS REQUEST 015. POWER ON 016. POWER OFF 018. INPUT SW CHANGE 020. PICTURE MUTE ON 021. PICTURE MUTE OFF 022. SOUND MUTE ON 023. SOUND MUTE OFF 024. ONSCREEN MUTE ON 025. ONSCREEN MUTE OFF 030. GAIN ADJUST 030-2. VOLUME ADJUST Volume Bass Treble Balance 030-12. IMAGE MODE ADJUST Aspect Ratio Input Signal 037. INFORMATION REQUEST 037-1. LAMP INFORMATION REQUEST 037-2. LAMP INFORMATION REQUEST 2 037-4.
In case of V300 series In case of VT series In case of NP600 series In case of NP610 series In case of NP2200 series In case of M300 series In case of P420 series In case of GT series In case of HT series In case of WT series In case of HT10 series In case of LT180 series In case of LT30 series In case of NP60 series In case of NP4000, 4100 series In case of U300 series In case of NP905/NP901W/VT800 20H 40H 40H 40H 40H 40H 40H 50H 60H 70H D0H D0H D0H D0H 80H 80H 90H (*3) Checksum: "CKS" inscription This i
Bit 7: Power On/Off processing 0 = No execution (Normal condition) 1 = During execution Bit 6: Selecting signal processing 0 = No execution (Normal condition) 1 = During execution Bit 5: Cooling processing 0 = No execution (Normal condition) 1 = During execution Bit 4: External control mode 0 = OFF 1 = ON Bit 3: No Power-Off period 0 = Power-Off Possible (Normal condition) 1 = Power-Off Impossible Bit 2: Reserved Bit 1: Projector status 0 = Idling 1 = Power On Bit 0: Reserved Response: At the time of a fail
01H: Power On DATA05 Cooling processing 00H: No execution (Normal condition) 01H: During execution DATA06 Indication signal number (Entry list number - 1) 0 ..
DATA32 Freeze Status (!2) 00H : OFF 01H : ON FFH : Not Supported DATA33 Test pattern display 1 00H : No display (Normal condition) 00H Other : Displaying (Pattern ID) Pattern ID Pattern Name 02H 03H 04H 05H 06H 07H 08H 09H 0AH 17H 18H 19H 1DH Cross Hatch Gray Bars Raster(0%) Raster(25%) Raster(50%) Raster(100%) Focus Raster Blue Gray Raster 30 Gray Raster 10 RAMP W BRG Blue Raster 60 Cross Hatch 3 MT LT LT180 LT80 HT GT W T VT NP1000 NP3150 NP905 NP4000 NP4100 NP62 * * * * * * * * * * * * * * * * * *
00H : No execution (Normal condition) 01H : During execution DATA69 Status of operation 00H : Idling 04H : Power On 05H : Cooling 06H : Idling (Error occurrence) Other than above: (nondisclosure) Internal use of code during a state transition period DATA70 ..
Data01 01H 01H 01H 01H 02H 02H 02H 02H 02H 02H 03H 03H 03H 04H 04H 04H 04H 05H 05H 06H 06H 08H 08H 08H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 11H 11H 11H 11H 11H 11H 11H 11H 12H 12H 12H 12H 12H 12H 12H 13H 13H 13H 13H 13H 13H 13H 14H 14H 15H 15H 15H 15H 16H 16H 16H Data70 00H 01H 02H 00H 00H 01H 02H 00H 00H 01H 00H 00H 00H 00H 01H 00H 01H 00H 00H 00H 00H 00H 00H 01H 00H 00H 01H 02H 03H 04H 00H 01H 02H 03H 05H 07H 08H 09H 01H 02H 00H 01H 00H 02H 03H 04H 00H 03H 00H 01H 00H 01H 02H 0
DATA72 PC Card insertion 00H : Not inserted 01H : Inserted DATA73 USB Mouse connection 00H : Not connected 01H : Connected DATA74 Entry list type 01H : Default 02H : User DATA75 .. 82 Reserved DATA83 DATA84 DATA85 On-screen mute 00H : OFF 01H : ON Reserved Indicate Contents 00H = Picture signal displaying 01H = No signal 02H = Viewer displaying 03H = Test pattern displaying 04H = LAN displaying DATA86 ..
009. ERROR STATUS REQUEST ********************************************************************** Function: This command acquires the error information occurring with the projector. Command: 00H 88H 00H 00H 00H 88H Response: At the time of a success 20H 88H 01H xxH 0CH DATA01 .. DATA12 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------* The various bits are normal is "0" and error is "1". * "None" is "0" fixation.
Supplement: (!) LT/LT80/HT: "None" 015. POWER ON ********************************************************************** Function: This command switches on the main power of the projector. Command: 02H 00H 00H 00H 00H 02H Response: At the time of a success 22H 00H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 00H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: The projector does not accept the other command during power on processing. 016.
DATA02 Switching number --------------------------------------------------------When the switching object is the "Signal list", the signal list number is specified. (0…99) --------------------------------------------------------When the switching object is the "Input connector", the input connector number is specified.
Response: At the time of a success 22H 03H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------DATA01 Results 00H : Normal FFH : Error Response: At the time of a failure A2H 03H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * When switch to the Video connector 02H 03H 00H 00H 02H 01H 06H 0EH 020.
022. SOUND MUTE ON ********************************************************************** Function: This command mutes the sound. Command: 02H 12H 00H 00H 00H 14H Response: At the time of a success 22H 12H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 12H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * Sound mute is cancelled for the following: Input connector switching Video signal switching Volume adjustment 023.
025. ONSCREEN MUTE OFF ********************************************************************** Function: This command cancels the blanking of the on-screen display. Command: 02H 15H 00H 00H 00H 17H Response: At the time of a success 22H 15H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 15H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) [030.
DATA03 : 00H (direct settings) 01H (increment/decrement) DATA04 : lower data (8bit) DATA05 : upper data (8bit) ex.1) volume direct setting (value = 20) DATA01 : 05H (Volume) DATA02 : 00H ("Volume" only) DATA03 : 00H (direct setting) DATA04 : 14H (lower data : 20 = 0014) DATA05 : 00H (upper data : 20 = 0014) ex.
------------------------------------------------------------------DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Volume to "10" 03H 10H 00H 00H 05H 05H 00H 00H 0AH 00H 27H 030-12. IMAGE MODE ADJUST ********************************************************************** Function: This command adjusts the Image Mode. Command: 03H 10H 00H 00H 05H DATA01 ..
DATA04 DATA05 Aspect Ratio 4:3 (Window) Aspect Ratio Normal / Auto (NP600, NP610, NP2200, NP62, NP64, NP216, P420, PA600, U300, V300 Series) Aspect Ratio 1.25:1(5:4) Aspect Ratio Letter Box (PA600 Series) Aspect Ratio 1.33:1(4:3) Aspect Ratio Wide Zoom (NP600, NP610, NP2200, NP62, NP64, NP216, P420, V300 Series) Aspect Ratio Wide Screen (PA600 Series) Aspect Ratio 1.
Supplement: (!) Lamp Hour Meter This is the timer for normal lamp mode conversion.
2) Punch in DATA12 DATA11 DATA10 DATA09 (006DDD00) 3) Change from HEX to Decimal - value will change to 7200000 seconds Lamp remaining time (in terms of Normal mode values) = (7200000 - 10800) / 3600 = 1997 hour 037-2. LAMP INFORMATION REQUEST 2 ********************************************************************** Function: This command acquires lamp remaining amount. Command: 03H 94H 00H 00H 00H 97H Response: At the time of a success 23H 94H 01H xxH 05H DATA01 ..
to appear (in terms of Eco mode values) 10H : Remaining time until inhibition of lamp usage (in terms of specified values) 11H : Remaining time until inhibition of lamp usage (in terms of Normal mode values) 12H : Remaining time until inhibition of lamp usage (in terms of Eco mode values) Response: At the time of a success 23H 96H 01H xxH 06H DATA01 ..
Function: This command acquires the information on the projector lamp.
Lamp Use Warning Starting Time 2000[H] Model. X = 100 - ((2100 * 100) / 2000) = -5[%] (!2) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!3) Lamp usage time This is the lamp total usage. It is displayed in the projector's menu. (!4) This setting is ignored, if the Item's unit is not time. (!5) NP4000/4001, NP4100/4100W : This function is not supported. 038.
00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 046. WXGA MODE SETTING REQUEST ********************************************************************** Function: This command acquires the setting of the WXGA Mode of projector.
01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) ====================================================================== 6. Response ---------------------------------------------------------------------* At the time of a success( ACK ) This returns ACK without adding data portion to the command that does not request data. This returns ACK with adding data to the data portion for the command that requests data.
Key number DATA01 DATA02 Key name -------------------------------------------1 01H 00H POWER 2 02H 00H POWER ON (!!) 3 03H 00H POWER OFF (!!) 4 04H 00H SOURCE (AUTO) (!!) 5 05H 00H AUTO (!) (!!) 6 06H 00H MENU (!!) (!!!) 7 07H 00H UP (!!) (!!!) 8 08H 00H DOWN (!!) (!!!) 9 09H 00H RIGHT (!!) (!!!) 10 0AH 00H LEFT (!!) (!!!) 11 0BH 00H ENTER (!!) (!!!) 12 0CH 00H CANCEL (!!) (!!!) 13 0DH 00H HELP (!!) (!!!) 14 0EH 00H POINTER 15 0FH 00H MAGNIFY UP 16 10H 00H MAGNIFY DOWN 17 11H 00H PICTURE MUTE 18 12H 00H SOU
81 82 83 84 85 96 132 133 134 135 136 137 138 158 159 163 164 165 166 167 200 201 214 215 216 217 218 221 222 223 225 226 227 228 229 232 233 237 238 51H 52H 53H 54H 55H 60H 84H 85H 86H 87H 88H 89H 8AH 9EH 9FH A3H A4H A5H A6H A7H C8H C9H D6H D7H D8H D9H DAH DDH DEH DFH E1H E2H E3H E4H E5H E8H E9H EDH EEH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H S-VIDEO1 (!!) S-VIDEO2 DIGITAL1 DIGITAL2 PC CAR
Command example: * Sending the AUTO key code 02H 0FH 00H 00H 02H 05H 00H 18H * Sending the AUTO (SHORT) key code 02H 0FH 00H 00H 02H DDH 00H F0H -----------------------------------------* cycle/toggle volume mute * cycle/toggle picture mute * cycle/toggle picture freeze 02H 0FH 00H 00H 02H DATA01 DATA02 CKS Data Portion Contents -------------------------------------------------------------------DATA01/DATA02 12H/00H : Volume mute DATA01/DATA02 11H/00H : Picture mute DATA01/DATA02 8AH/00H : Picture freeze --
Function: This command acquires the Carbon Saving values on the projector.
Function: This command acquires the adjustment values. Command: 03H 04H 00H 00H 03H DATA01 .. DATA03 CKS (*3) Data Portion Contents ------------------------------------------------------------------DATA01 .. 02 Acquirement items (!) DATA03 00H fixed Response: At the time of a success 23H 04H 01H xxH 0DH DATA01 ..
(! ) Acquirement items DATA01 00H 01H 02H 03H 04H 05H 05H 05H 06H 06H 06H 06H 06H 07H 08H 08H 09H 09H 0AH 0BH 0CH 0CH 0DH 0DH 0EH 0EH 0FH 0FH 10H 10H 13H 14H 14H 14H 14H 14H 14H 15H 15H 16H 18H 18H 19H 1AH 1BH 1CH 1DH 21H 21H 22H 23H 24H 25H 25H 25H 26H 27H 28H 28H 28H 28H 29H 29H 29H 29H 2AH 2BH 2BH 2CH 2CH DATA02 Acquirement name 00H 00H 00H 00H 00H 00H 01H 02H 00H 01H 02H 03H 04H 00H 00H 01H 00H 01H 00H 00H 00H 01H 00H 01H 00H 01H 00H 01H 00H 01H 00H 00H 01H 02H 03H 04H 05H 00H 01H 00H 00H 01H 00H 00H 0
4CH 4CH 4CH 4CH 4DH 4EH 4EH 4EH 4FH 50H 51H 51H 52H 52H 52H 53H 54H 54H 54H 54H 54H 54H 54H 55H 56H 57H 58H 59H 5AH 5AH 5AH 5AH 5AH 5AH 5AH 5AH 5AH 5BH 5CH 5DH 5EH 5FH 5FH 5FH 5FH 5FH 5FH 5FH 60H 61H 61H 61H 62H 62H 62H 63H 63H 63H 63H 63H 63H 64H 64H 64H 64H 64H 64H 65H 65H 65H 65H 65H 65H 66H 07H 08H 09H 0AH 00H 00H 01H 02H 00H 00H 00H 01H 00H 01H 02H 00H 00H 01H 02H 03H 04H 05H 06H 00H 00H 00H 00H 00H 00H 01H 02H 03H 04H 05H 06H 07H 08H 00H 00H 00H 00H 00H 01H 02H 03H 04H 05H 06H 00H 00H 01H 02H 00H 01H
077. MUTE CONTROL ********************************************************************** Function: This command controls the mute of picture, sound and on-screen.
DATA01 DATA02 DATA03 01H 01H 01H 01H 02H 02H 02H 02H 02H 02H 03H 03H 04H 04H 04H 04H 05H 06H 06H 08H 08H 08H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 11H 11H 11H 11H 11H 11H 11H 11H 11H 12H 12H 12H 12H 12H 12H 12H 13H 13H 13H 13H 13H 13H 13H 14H 14H 15H 15H 15H 15H 16H 16H 16H 00H 01H 02H 00H 00H 01H 02H 00H 00H 01H 00H 00H 00H 01H 00H 01H 00H 00H 00H 00H 00H 01H 00H 00H 01H 02H 03H 04H 00H 01H 02H 03H 05H 07H 08H 09H 01H 02H 00H 01H 00H 02H 02H 03H 04H 00H 03H 00H 01H 00H 01H 02H 00
DATA04 Sound function 00H : Not available 01H : Available DATA05 Calendar function 00H : No function 01H or 03H : Timer function, sleep timer function 02H : Sleep timer function DATA06 .. 32 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-2. RUNNING STATUS REQUEST ********************************************************************** Function: This command acquires the status of the projector operation.
01H : Connected DATA09 .. 16 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-3. INPUT STATUS REQUEST ********************************************************************** Function: This command acquires the status of input signal of the projector. Command: 00H 85H 00H 00H 01H 02H 88H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 ..
DATA06 Test pattern display 00H : No display(Normal condition) 01H : Displaying DATA07 ..08 Reserved DATA09 Indicate Contents 00H = Picture signal displaying 01H = No signal 02H = Viewer displaying 03H = Test pattern displaying 04H = LAN displaying DATA10 .. 16 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-4.
078-5. MODEL NAME REQUEST ********************************************************************** Function: This command acquires the model name of the projector. Command: 00H 85H 00H 00H 01H 04H 8AH Response: At the time of a success 20H 85H 01H xxH 20H DATA01 .. DATA32 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------DATA01 ..
[079. FREEZE CONTROL] ********************************************************************** Function: This command controls the freeze.
Command: 03H B0H 00H 00H 02H DATA01 DATA02 CKS Data Portion Contents ------------------------------------------------------------------DATA01 C5H fixed DATA02 Acquisition Object 00H : MODE 01H : POSITION 02H : SOURCE Response: At the time of a success 23H B0H 01H xxH 03H DATA01 DATA02 DATA03 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------DATA01 C5H fixed DATA02 Acquisition item(Same as DATA02 of the transmit data) DATA03 Setting Value if DATA02 is
02H : BOTTOM-LEFT 03H : BOTTOM-RIGHT if DATA02 is SOURCE(02H) 00H : OFF 01H : VIDEO 02H : S-VIDEO Response: At the time of a success 23H B1H 01H xxH 03H DATA01 DATA02 DATA03 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------DATA01 00H fixed DATA02 Update target ( Same as DATA02 of the transmit data ) DATA03 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 110.
111. AUTO ADJUST EXECUTE2 ********************************************************************** Function: This command executes the Auto Adjust. Command: 03H BAH 00H 00H 01H 00H BEH Response: At the time of a success 23H BAH 01H xxH 01H 00H CKS (*1) (*2) (*3) Response: At the time of a failure A3H BAH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-1. BASE MODEL TYPE REQUEST ********************************************************************** Function: This command acquires the projector type.
DATA02 DATA03 DATA13 DATA14 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 00H 01H 01H 00H 00H 00H 00H 00H 02H 02H 00H 00H 03H 03H 03H 01H FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH FFH 01H 01H 01H 01H 02H 02H 02H 02H 02H 02H 02H 02H 02H 03H 03H 03H 04H 04H 04H 05H 05H 05H 05H 06H 06H 08H 08H 08H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 10H 11H 11H
DATA15 ... 16 Reserved Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-3. PROJECTOR INFORMATION REQUEST ********************************************************************** Function: This command acquires basic operation states of projector. Command: 00H BFH 00H 00H 01H 02H C2H Response: At the time of a success 20H BFH 01H xxH 10H DATA01 ...
09H : SLOT2 0AH : SLOT3 0BH : SLOT4 0CH : DIGITAL2 0DH : SCART 10H : AUTO FFH : Not Source Input Other : Not Support DATA06 Indication signal type (Effective only when Select source input type 2 is 02H or 03H) x0H : NTSC3.58 x1H : NTSC4.43 x2H : PAL x3H : PAL60 x4H : SECAM x5H : B/W60 x6H : B/W50 x7H : PALNM x8H : NTSC3.58 LBX x9H : NTSC3.
====================================================================== 6.1. Response ---------------------------------------------------------------------* At the time of a success (ACK) This returns ACK without adding data portion to the command that does not request data. This returns ACK with adding data to the data portion for the command that requests data. * At the time of a failure (NAK) This adds a cause of not accepting the command to data portion to return it.
