HIGH DEFINITION RECEIVER / RECORDER Model : NHD-3000PVR
USER’S MANUAL HIGH DEFINITION RECEIVER / RECORDER Model : NHD-3000PVR
Warnings 01 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
01 Warnings 7. Water and Moisture : Do not use the product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub ; in a wet basement ; or near a swimming pool ; and the like. 8. Accessories : Do not place this product on an unstable table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a table recommended by the manufacturer, or sold with the product.
Warnings 01 b) If liquid has been spilled, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an importer adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
02 Table of Contents 01. Warnings 1 02. Table of Contents 4 03. Supplied Accessories 6 04. Controls Front Panel Controls and LEDs 7 Rear Panel Connectors 8 Battery Installation for Remote Control 10 05.
Table of Contents 02 Teletext 34 PIP Control 35 08. Channel Channel Edit 36 Channel Scan 37 Manual Scan 38 Channel Sorting 39 Channel Duplication 40 Parental Rating 41 09. Audio/Video HDMI Video 42 HDMI Audio 43 Monitor Setup 44 Digital Audio Out 45 PIP Size 46 Vol. Control 47 10. PVR Manager Program List 48 Skip Time 49 HDD Sleep Time 50 HDD Format 51 11.
03 Supplied Accessories Make sure the following accessories are provided with product. 1. Remote Control 4. Component Video Cable 5. Audio Cable(L/R) 2. Batteries (size AAA) 6.HDMI Cable 3. User’s Guide 7.
Front Panel Controls and LED’s 04 Remote Control Sensor STANDBY Power & Remote Indicator LED Front Display Timeshift Playback Indicator LED Recording Indicator LED OK MENU EXIT POWER Arrow Buttons Front Side Front Display Power On Channel number is displayed. C100 means digital channel number is 100. A200 means radio channel number is 200. Power Off Clock is displayed. LED Indicators STANDBY STANDBY Power & Remote Sensor Indicator LED.
04 Rear Panel Connectors Antenna Input A/V Output HDMI/DVI Output Optical Audio Output Power Cord Service Port Rear Side ◈ Note. Connection of input/output connector in rear panel should be done while power is OFF. Power Cord Connect to the AC power (AC 240 ~ 250V / 50Hz). Antenna Input Connect the cable from an off-air TV antenna to Antenna1 input. Connect Antenna1 loop out to Antenna2 input with RF loop cable.
Rear Panel Connectors (Cont.
04 Battery Installation for Remote Control Remove the battery cover and install batteries like the diagram below. 1. Unlatch the battery compartment cover on the back of remote control. 2. Insert 2 AAA batteries as shown, making sure the + and - ends of each battery line up with the corresponding marks in the battery compartment. 3. Snap the cover back to the remote control.
Antenna Input 05 THE RF LOOP CABLE MUST BE CONNECTED, OTHERWISE THE UNIT WILL NOT BE ABLE TO TUNE. Connecting Antenna Connect the antenna or RF cable wire directly to ANTENNA1 IN and connect ANTENNA1 Loop Out to ANTENNA2 Input by using RF loop cable. ◈ NOTE · The STB(Set Top Box) should be unplugged before connecting antenna. (Power OFF mode) · The RF OUT from the tuner will only work when the unit turns on. It will not give RF OUT during STANDBY mode.
05 Connection to Digital TV (YPbPr) < Digital TV > Connect the Video Cables Connect a video cable between the Component video output(Y : Green, Pb : Blue, Pr : Red) jacks of the STB(Set Top Box) and the Component input jacks on the Digital TV according to corresponding colour. On the Video Out Mode, select YPbPr as Video Output Type and select one of 1080i, 720p, 576p, 576i as Video Output Resolution according to your digital TV.
Connection to Digital TV (RGB/HV) 05 < Digital TV > Connect the Video Cables Connect the RGB/HV output jack of the STB to the RGB input jack of the PC RGB input on the digital TV. In regard to the Video Out Mode, select RGB as Video Output Type and select one of 1080i, 720p, 576p as Video Resolution according to your digital TV. ◈ NOTE · By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’.
05 Connection to RGB PC Monitor Connect the Video Cables Connect RGB/HV video output jack of the STB to the RGB jack of the PC monitor. In regard to the Video Out Mode, select RGB as Video Output Type and select one of 1080i, 720p, 576p according to Video Output Resolution of your PC monitor. ◈ NOTE · By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’.
Connection to Digital TV (HDMI/DVI) 05 < Digital TV > Connect the HDMI Cable Connect the HDMI/DVI output jack of the STB to the HDMI input jack of the digital TV. In regard to the Video Out Mode, select one of 1080i, 720p, 576p as Video Resolution according to your digital TV. ◈ NOTE · By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’.
05 Connection to HDMI/DVI PC Monitor Connect the Video Cables Connect HDMI/DVI jack of the STB to the HDMI/DVI jack of the PC monitor. In regard to the Video Out Mode, select one of 1080i, 720p, 576p according to Video Output Resolution of your monitor. (Purchase HDMI-to-DVI adapter.) ◈ NOTE · By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’.
Connection to Analog TV (Composite/S-Video) 05 < Analog TV > If you use Composite/S-VIDEO connection, you must select 576i format. Otherwise all of the OSD (On Screen Display) will not function, including MENU, MARK, etc. Connect the Video Cables Connect a composite cable between the Video output jack of the STB and the Video input jack of the analog TV. Or, connect an S-Video cable between the S-Video output jack of the STB and the S-Video input jack of the analog TV.
05 Connection to Digital Audio Amplifier < Audio Amplifier > Connect the Digital Audio Output Connect audio cables from the OPTICAL or COAXIAL digital audio output jacks of the STB to the OPTICAL or COAXIAL digital audio input jacks of the digital audio decoder or the amplifier. Do not connect the coaxial and optical audio output simultaneously and be sure to connect either optical or coaxial cable to avoid any damage to digital audio decoder or amplifier that may occur.
Remote Control 06 Power TV/Radio Number Teletext CC VOL + / Mute PIP ON/OFF , PIP Channel , PIP Swap , PIP Position Favourite CH + / Favourite CH Add/Del Aspect Ratio Recall Channel List Info / Guide Arrow Left /Right Drag - / + Arrow Up / Down Skip + / - Exit Menu OK Play / Slow , Pause Stop , Record / Edit Rewind , Fast Forward Start , End Timer Record , Mark(Status) Video Output Video Format 19 Timeshift , Program List Snap(Freeze) Basic Operation
06 Remote Control (Cont.) Button Description Press to turn the power ON or OFF. Select TV or Radio Channel. Channel Number Buttons from #0 to #9. Press to directly tune to a particular channel. Press to turn Closed Captions on / off. Press to turn Teletext on / off. Usage in Teletext mode RED, GREEN:Page Up/Down, Yellow:Freeze Teletext, BLUE:Unfreeze Teletext Usage for PIP functions ON/OFF : Enable or disable PIP display. CH : Select channel for PIP display .
Remote Control (Cont.) 06 Button Description < ▲▼ > : Channel Up/Down or Menu navigation in up or down direction. < ◀▶ > : Menu navigation in left or right direction. < OK > : Selection. < Skip +/- > : Forward or backward skip. < Drag +/- > : Move to the location where you want to playback. Press to display or exit the on-screen Menu. Press to switch back to the previous Menu screen that was displayed. Starts playback. Press PLAY/SLOW during playback then the unit will go into Slow mode.
07 Channel Information Press the INFO button to display the following screen. 1. RF Signal Strength 2. Channel Number 3. A/V Info. 4. Current Time 7. Next Program 8. Parental Guidance Rating 6. Current Program 5. Service Provider and Service Name 9. Timeshift Playback 10. Record (Tuner #1) 11. Record (Tuner #2) 1. RF Signal Strength Indicates the signal strength of the selected channel. 7. Next Program Displays next program name of current channel. 8. Parental Guidance Rating 2.
Channel Guide (EPG) 07 Press INFO/GUIDE button twice to select Channel Guide (EPG). 1. Press INFO/GUIDE button twice. 2. Press ▲, ▼, FAV.CH(+/-) buttons to change the channel. ※ To exit immediately, press the EXIT button.
07 Channel Status Press MARK(STATUS) button to display current channel status and information. Press MARK(STATUS) button to display main channel status and information. It displays service provider name, service provider title, physical channel number, source video format, output video format and signal quality. ·Press MARK(STATUS) button twice, then you can see PIP channel status. ※ Mark function is activated when play bar OSD is on. ※ To exit immediately, press the EXIT button.
Channel List 07 Press LIST button to select channel on Channel List menu. For channel change, add or delete 1. Press LIST or OK button. 2. Press ▲,▼ button to highlight ‘Channel List’. 3. Press OK button to tune. 4. Press ▶ button to add channels to ‘Channel List’ or press ◀ button to delete channels to ‘Channel List’. If channel is added to ‘Channel List’, the colour of the channel number is changed to white.
07 Timeshift Control Press T.SHIFT button to start timeshift. Start Timeshift : Press PAUSE button or T.SHIFT button. The timeshift logo will be displayed during timeshift. Stop Timeshift : Press STOP[ ] button (follow the instruction from OSD), then press OK button. Available functions during Timeshift : 1.Starting point of timeshift : START[ ] button. 2.Ending point of timeshift : END[ ] button. 3.SCAN : FF[ ] button. ] button or REW[ 4.
Record Control (Dual Recording) 07 Press REC/EDIT button to select recording time. This NHD-3000PVR has two digital tuners in it. One can be displayed as MAIN picture, while another one can be displayed as PIP (Picture in Picture).
07 Timer Record List Show the Timer Record List. 1. Press T.REC button. 2. On the Timer Record List, press · ▲,▼ button to select a program then press OK to display the Edit window. Refer to 3. · ▶ button to add new program. Refer to 3. · ◀ button to delete selected program. 3. On the Edit Window, press ◀, ▶ button to move to next or previous column then use ▲,▼ button to change a setting for the selected column. When all is done, press OK button to change or add the program. · Program : Select program.
Program List 07 Show the Program List. 1. Press P.LIST button to playback a recorded program. 2. Use ◀, ▶ button to select a program. 3. Press OK button to playback the selected program. 4. If new program to be played is same as the previously played one, it will play at the position where you were watching. (Resume function) 5. Press ▼ button to display options. The options will be displayed as shown above. · Play In Main : Play the selected program in main window.
07 Program List (Rename) Show the Program List(Rename). 1. : Capital Letter, 2. : Refer to the letters in remote control. Remote Button 0 Capital Letter Small Letter 0 Number 3. 4. 5. 6. Small Letter, Number. 1 2 3 4 5 6 7 8 9 .QZ ABC DEF GHI JKL MNO PRS TUV WXY .qz abc def ghi jkl mno prs tuv wxy 1 2 3 4 5 6 7 8 9 : Delete previous letter or backspace. : Move to next letter or insert blank space. : Cannel renaming. : Execute renaming.
Playback Control 07 Control Playback. Choose Program List : Press P.LIST button or go to MENU and choose a ‘Program List’. Slow Motion : For slow motion press PLAY/SLOW [ ] button during normal playback mode. Press PLAY/SLOW [ ] button when returning to normal playback mode. SCAN : For scan mode, press FF [ ] button or REW [ to go to normal playback mode during FF or REW mode. ] button. Press OK button or PLAY button Smart Skip : SKIP+, SKIP- button. (Skip time can be set in Menu.
07 EDIT Control (Repeat, Cut, Split) Control Repeat, Cut & Split. EDIT works only during Playback mode and provide three functions. To enter into EDIT function, press REC/EDIT button during playback mode. MARK has to be used before the operation of these functions. REPEAT/CUT requires two MARKs. SPLIT requires one MARK. Repeat : Repeat area can be set using MARK, DRAG+, and DRAG- buttons. After setting the repeat area, press REC/EDIT button again, then REPEAT, CUT, SPLIT options will shown.
Closed Caption 07 Press CC button to turn on/off closed caption. 1. To turn on or off caption press CC button. 2. Every time CC button is pressed, ‘Caption On’ icon or ‘Caption Off’ icon will appear in due order.
07 Teletext Press TTX button to display current teletext. Press ▲,▼ button to turn pages up and down, press number 100 to 899 to turn the direct number page. 1. Press TTX button to display current teletext. 2. Press ▲ or ▼ button to go to pages up or down. 3. Press number 100 to 899 to go to the numbered page. Available buttons during TTX mode : ·RED button : Page Down ·GREEN button : Page Up ·YELLOW button : Freeze Teletext ·BLUE button : Unfreeze Teletext ※ To exit immediately, press the TTX button.
PIP Control 07 Control PIP channel. PIP Turn On/Off : Press PIP ON/OFF button to turn on or off PIP. PIP Channel Change : Press PIP CH button and PIP channel list is poped up. PIP Express Channel Up: Keep on pressing PIP CH button, when PIP channel OSD is on, then PIP channel move to upside. PIP Change Position : Press PIP POS button to change PIP position. Swap PIP & Main Video : Press PIP SWAP button to swap PIP for Main Program.
08 Channel Edit Memorize your choice of channels. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Press ▲,▼ button to highlight‘Channel Edit’. 4. Press OK to tune. 5. Press ▶button to add channels to‘Channel List’or press ◀ button to delete channels to ‘Channel List’. If channel is added to‘Channel List’, the colour of the channel number is changed to white. If a channel is deleted from‘Channel List’, the colour of the channel number is changed to black. 6.
Channel Scant 08 Have an automatic channel set up. The Auto Search selects currently available channels. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Press ▲,▼ button to highlight‘Channel Scan’. 4. The STB will automatically scan and store all of the channels that are available in your local area. (To stop the auto searching, press EXIT button.) 5. The scanned channel is displayed when done. 6.
08 Manual Scan Have an manual channel set up. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Manual Scan’, then press OK. 4. Press ◀,▶ button to select physical channel, or press‘0’to‘9’button to input channel frequency. 5. Press OK button to tune and Memorize channel information. ※ After selecting the physical number/frequency, if a signal is received correctly, a message of“LOCK” will be displayed, otherwise“UNLOCK”will be displayed.
Channel Sorting 08 Select Channel Sorting Method. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Channel Sorting’then press OK. 4. Press ▲,▼ button to make a choice, then press OK. ㆍBy Logical :‘Channel List’is sorted by logical channel number. ㆍBy Physical :‘Channel List’is sorted by physical channel number. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
08 Channel Duplication Select Channel Duplication Option. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Channel Duplication’then press OK. 4. Press ▲,▼ button to make a choice, then press OK. Channel Duplication function is to decide if all the duplicated physical channel for the same logical channel are listed in ‘Channel List’ or not.
Parental Rating 08 Set Parental Guidance Rating. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK 3. Use ▲,▼ button to highlight‘Parental Rating’icon, then press OK. 4. Enter password to proceed. 5. Use ▲,▼ button to highlight‘Set’icon, then press OK. 6. Use ▲,▼ button to make a choice from the rating levels, then press OK. ㆍ No Block ㆍ R & Above ㆍ AV & Abov ㆍ MA & Above ㆍ M & Above ㆍ PG & Above ㆍ G & Above ㆍ Block All The factory default password is 0–0–0–0.
09 HDMI Video Control HDMI video output. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘HDMI Video’, then press OK. 4. Press ▲, ▼ button to make a choice, then press OK. HDMI means the value of video timing is setup for HDMI It will take a few seconds to set HDMI video mode, if mode selection is changed from HDMI to YPbPr/RGB or vice versa. HDMI mode supports HDMI1080i, HDMI720p, HDMI576p, 1080i, 720p, 576p, and 576i .
HDMI Audio 09 Control HDMI audio output. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘HDMI Audio’, then press OK. 4. Press ▲, ▼ button to make a choice, then press OK. ㆍ Auto : If the broadcaster is broadcasting PCM/MPEG, the Digital OUT will be PCM. If the broadcaster is broadcasting Dolby Digital, the Digital OUT will be Dolby Digital.
09 Monitor Setup Adjust display position. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Monitor Setup’, then press OK. 4. Customize the Monitor type to fit user’s TV or display. ㆍ16 : 9 ㆍ4 : 3 ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
Digital Audio Out 09 Controls audio output type. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Digital Audio Out.’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ㆍPCM : Digital Audio Output is always PCM. ㆍDolby D : Digital Audio Output is Dolby Digital in case of Dolby Digital audio stream come in. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
09 PIP Size Set up the PIP size. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘PIP Size’, then press OK. 4. Press ▲, ▼, ◀, ▶ button to make a choice, then press OK. ㆍPIP size can be chosen from ‘Large’, ‘Medium’, or ‘Small’. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
Vol. Control 09 Turn on and off the remote controller volume control functionality. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Vol. Control’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ㆍOFF : Volume of the STB can NOT be controlled by remote control. ㆍON : Volume of the STB can be controlled by remote control. ※ When the volume is off, the MUTE button will operate as normal.
10 Program List The Program List shows the recorded programs. (You can also bring up the Program List by pressing the P.LIST button on the remote control.) 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Program List’, then press OK. 4. On the Program List, press ◀, ▶ button to select a program. 5. Press OK button to playback the selected program. 6. Press ◀ button to delete the selected program. 7. Press ▶ button to add the selected program.
Skip Time 10 Set up how much time will be skipped when user press SKIP+, SKIP- button. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Skip Time’, then press OK. 4. Press ▲, ▼ button to make a choice, then press OK. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
10 HDD Sleep Time Set up how much time the HDD will be powered on after the HDD has no works to do. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘HDD Sleep Time’, then press OK. 4. Press ▲, ▼ button to make a choice, then press OK. ※ In HDD Auto Sleep mode, if HDD is not used for 3 minutes, the HDD will enter into sleep mode. When you want to use HDD again, it will take 2 or 3 seconds to escape from HDD sleep mode.
HDD Format 10 Formats the HDD. All the recorded programs will be deleted. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘HDD Format’, then press OK. 4. Enter password to proceed. 5. Press OK to start HDD format. Caution If you format the HDD, everything recorded on the HDD will be erased. ※ The factory default password is 0–0–0–0.
11 Opacity Control opacity (transparent) of menu screen. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Opacity’, then press OK. 4. Press ▲,▼ button to make a choice, then press OK. ㆍOpacity1 : Very Dark ㆍOpacity2 : Dark ㆍOpacity3 : Light ㆍOpacity4 : Very Light ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
Time Zone 11 Select time zone. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Time Zone’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ㆍNSW/ACT ㆍVIC/TAS ㆍQLD ㆍSA ㆍWA ㆍNT ㆍAuto Time Zone ※ If the automatic clock setting is not correct, go to the channel that broadcasting teletext and press TTX button. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
11 Daylight Saving Select daylight saving. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Daylight Saving’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ㆍOff : Daylight Saving is off. ㆍOn : Daylight Saving is on. ※ If you select‘Auto time Zone’, Daylight Saving On/Off does not work. ※ If the automatic clock setting is not correct, go to the channel that broadcasts teletext and press TTX button.
Sleep Timer 11 Select the time in which the unit is to be turned off. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘Sleep Timer’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
11 New Password Change the 4-digit password. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘NEW PASSWORD’icon, then press OK. 4. Enter password to proceed. 5. Enter new password and make a confirmation using number keys on the remote controller. ※ The factory default password is 0-0-0-0. ※ For any reason, if you forget the password, Press MENU, CC, 3,6,9 button sequentially, then the password will be back to ‘0000’ again.
Factory Default 11 Set Factory Default. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK 3. Use ▲,▼ button to select Factory Default, then press OK. 4. Enter password to proceed. 5. Press OK button to set to Factory Default. ※ The factory default password is 0-0-0-0. ※ For any reason, if you forget the password, Press MENU, CC, 3,6,9 button sequentially, then the password will be back to ‘0000’ again. ※ Set to Factory Default takes 25 second.
11 About Show the software version and date. 1. Press MENU button. 2. Use ▲,▼ button to highlight‘ ’icon, then press OK. 3. Use ▲,▼ button to highlight‘About’, then press OK. 4. Use ▲,▼ button to make a choice, then press OK. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen.
Specifications 12 ITEM Product Name SPECIFICATIONS High Definition Receiver / Recorder Model NHD-3000PVR Supply Voltage AC 240V, 50Hz Power Consumption Size (W X H X D) Weight (Kg) Channel Antenna Impedance Operation : 25W max, Standby : 1W max 335mm x 65mm x 270mm NET : 3.0 Kg, GROSS : 4.
NEC Australia Pty. Ltd.
