Electronics America Switch Reference Guide
Table Of Contents
- SmartPanel
- Browser-based interface
- Command Line Interface
- Introduction
- Information Menu
- Introduction
- Menu overview
- System Information Menu
- SNMPv3 Information Menu
- System information
- Show last 100 syslog messages
- System user information
- Layer 2 information
- FDB information menu
- Trunk group information
- Layer 3 information
- ARP information
- IP information
- IGMP multicast group information
- IGMP multicast router port information
- Link status information
- Port information
- Group information
- Information dump
- Statistics Menu
- Configuration Menu
- Introduction
- System configuration
- System host log configuration
- Secure Shell Server configuration
- RADIUS server configuration
- TACACS+ server configuration
- NTP server configuration
- System SNMP configuration
- SNMPv3 configuration
- SNMPv3 User Security Model configuration
- SNMPv3 View configuration
- SNMPv3 View-based Access Control Model configuration
- SNMPv3 Group configuration
- SNMPv3 Community Table configuration
- SNMPv3 Target Address Table configuration
- SNMPv3 Target Parameters Table configuration
- SNMPv3 Notify Table configuration
- System Access configuration
- Port configuration
- Spare Ports Group configuration
- Group configuration
- Configuration Dump
- Saving the active switch configuration
- Restoring the active switch configuration
- Operations Menu
- Boot Options Menu
- Maintenance Menu
Command Line Interface 79
Group configuration
Command: /cfg/group <1-5>
[Group 1 Menu]
addport - Add ports to the group
remport - Remove ports from the group
addvlan - Add non-default (tagged) VLANs to the group
remvlan - Remove non-default (tagged) VLANs from the group
pvid - Set default port VLAN id for the group
igmp - Enable/Disable IGMP Snooping for the group
failover - Enable/Disable Failover for the group
limit - Number of External Links to trigger failover
lacp - Enable/Disable LACP for the group
cur - Display current group configuration
Use these menu options to set the Port Group. There are five Port Groups. Set the ports, which Port Group 1-5 do
not contain, to Spare Ports Group.
The following table describes the Port Group Configuration menu options.
Table 82 Port Group Configuration menu options
Command Description
addport <port number> Adds the specified port to the Port Group.
remport <port number> Removes the specified port from the Port Group.
addvlan <1-4094> Adds the non-default (tagged) VLAN to the Port Group.
remvlan <1-4094> Removes the non-default (tagged) VLAN from the Port Group.
pvid <1-4094> Sets default port VLAN ID (PVID) to the Port Group. The default is automatically
assigned when the Group is used.
igmp disable|enable Enables or disables IGMP snooping for the Port Group.
failover
disable|enable
Enables or disables Failover for the Port Group. The default is enabled. When it is
enabled and the number of external links is the value of the limit or fewer, the switch
disables the internal server blade port of the Port Group.
limit <0-4> Sets the number of external links to trigger failover. The default is 0. The failover limit
lets you specify the minimum number of operational links required within the failover
trigger before the trigger initiates a failover event. For example, if the limit is four, a
failover event occurs when the number of operational links in the trigger is four or
fewer. When you set the limit to zero, the SmartPanel triggers a failover event only
when no links in the trigger are operational.
lacp disable|enable Enables or disables LACP for the Port Group. The default is disabled. When
disabled, the external ports of the Port Group are configured as a static trunk group.
When enabled, they are configured as a LACP trunk group.
cur Displays the current Ports Group configuration.
NOTE: A Port Group must contain at least one external port (20-24) and one internal server blade port (1-
16).
See the “Port Group Mapping” section in the “Browser-based interface” chapter for information.