Electronics America Switch Reference Guide
Table Of Contents
- SmartPanel
- Browser-based interface
- Command Line Interface
- Introduction
- Information Menu
- Introduction
- Menu overview
- System Information Menu
- SNMPv3 Information Menu
- System information
- Show last 100 syslog messages
- System user information
- Layer 2 information
- FDB information menu
- Trunk group information
- Layer 3 information
- ARP information
- IP information
- IGMP multicast group information
- IGMP multicast router port information
- Link status information
- Port information
- Group information
- Information dump
- Statistics Menu
- Configuration Menu
- Introduction
- System configuration
- System host log configuration
- Secure Shell Server configuration
- RADIUS server configuration
- TACACS+ server configuration
- NTP server configuration
- System SNMP configuration
- SNMPv3 configuration
- SNMPv3 User Security Model configuration
- SNMPv3 View configuration
- SNMPv3 View-based Access Control Model configuration
- SNMPv3 Group configuration
- SNMPv3 Community Table configuration
- SNMPv3 Target Address Table configuration
- SNMPv3 Target Parameters Table configuration
- SNMPv3 Notify Table configuration
- System Access configuration
- Port configuration
- Spare Ports Group configuration
- Group configuration
- Configuration Dump
- Saving the active switch configuration
- Restoring the active switch configuration
- Operations Menu
- Boot Options Menu
- Maintenance Menu
Command Line Interface 72
SNMPv3 Group configuration
Command: /cfg/sys/ssnmp/snmpv3/group <group number>
[SNMPv3 vacmSecurityToGroup 1 Menu]
model - Set security model
uname - Set USM user name
gname - Set group name
del - Delete vacmSecurityToGroup entry
cur - Display current vacmSecurityToGroup configuration
The following table describes the SNMPv3 Group Configuration Menu options.
Table 69 SNMPv3 Group Configuration Menu options
Command Description
model
usm|snmpv1|snmpv2
Defines the security model.
uname <1-32
characters>
Sets the user name as defined in /cfg/sys/ssnmp/snmpv3/usm/name. The
user name can have a maximum of 32 characters.
gname <1-32
characters>
Configures the name for the access group as defined in
/cfg/sys/ssnmp/snmpv3/access/name. The group name can have a
maximum of 32 characters.
del Deletes the vacmSecurityToGroup entry.
cur Displays the current vacmSecurityToGroup configuration.
SNMPv3 Community Table configuration
Command: /cfg/sys/ssnmp/snmpv3/comm <comm number>
[SNMPv3 snmpCommunityTable 1 Menu]
index - Set community index
name - Set community string
uname - Set USM user name
tag - Set community tag
del - Delete communityTable entry
cur - Display current communityTable configuration
This command is used for configuring the community table entry. The configured entry is stored in the community
table list in the SNMP engine. This table is used to configure community strings in the Local Configuration
Datastore (LCD) of SNMP engine.
The following table describes the SNMPv3 Community Table Configuration Menu options.
Table 70 SNMPv3 Community Table Configuration Menu options
Command Description
index <1-32
characters>
Configures the unique index value of a row in this table. The index can have a maximum
of 32 characters.
name <1-32
characters>
Defines a readable 32 characters string that represents the corresponding value of an
SNMP community name in a security model.
uname <1-32
characters>
Defines the name as defined in /cfg/sys/ssnmp/snmpv3/usm/name. The name
can have a maximum of 32 characters.
tag <1-255
characters>
Configures a tag of up to 255 characters maximum. This tag specifies a set of transport
endpoints to which a command responder application sends an SNMP trap.
del Deletes the community table entry.
cur Displays the community table configuration.