NEC Technologies LCD Projector User’s Manual MT830+™/MT1030+™/MT1035+™ MultiSync ® NEC Multimedia Theatre NEC Multimedia Theatre NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 Part No.
I M P O R T A N T I N F O R M A T I O N Precautions CAUTION Please read this manual carefully before using your NEC MultiSync MT830+/MT1030+/MT1035+ LCD Projector and keep the manual handy for future reference. To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
Important Safeguards These safety instructions are to ensure the long life of your LCD projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation 1. For best results, use your LCD projector in a darkened room. 2. Place the projector on a flat, level surface in a dry area away from dust and moisture. 3. Do not place your LCD projector in direct sunlight, near heaters or heat radiating appliances. a.
5 ATTENTION ATTENTION RISQUE D’ELECTROCUTION NE PAS OUVRIR ATTENTION RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU LONGUEUR D’ONDE: 645 nm (640-660 nm) MAX. SORTIE: 1 mW APPREIL A LASER DE CLASSE 2 AVERTISSEMENT AFIN DE REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND.
7 4. La fumée, la vapeur et l’exposition aux rayons directs du soleil risquent de détériorer sérieusement les composantes internes. 3. Si le projecteur à écran à cristaux liquides (LCD) n’est pas utilisé pendant une période prolongée, retirer la fiche de la prise secteur. 5. Eviter des manipulations brusques lors du déplacement du projecteur à écran à cristaux liquides (LCD), car un choc violent pourrait endommager les composantes internes. Nettoyage 6.
L I M I T E D W A R R A N T Y NEC MultiSync LCD Projector Products ® 9 NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms. 2. Any product on which the serial number has been defaced, modified or removed. NECTECH’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR ‘LIKE NEW’. HOW LONG IS THE WARRANTY? 3.
T A B L E O F C O N T E N T S 11 1. Introduction Introduction To The MultiSync MT830+/MT1030+/MT1035+ LCD Projector .............. 13 How Do You Get Started? ............................................................................................... 15 What’s In The Box? ........................................................................................................ 15 Getting To Know Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector ......... 17 Front / Rear Features .....................
1 I N T R O D U C T I O N This section introduces you to your new MultiSync MT830+ (SVGA)/ MT1030+ and MT1035+ (XGA) LCD Projector, provides a list of materials that comes with your projector and describes the features and controls. Congratulations On Your Purchase Of The MultiSync MT830+/MT1030+/MT1035+ LCD Projector The MultiSync MT830+/MT1030+/MT1035+ is one of the very best LCD projectors available today.
15 How Do You Get Started? The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to watch the introductory video and review the manual. This may save you hours later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it. What’s In The Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
17 Getting To Know Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector Front Features AC Input Plug the female end of the supplied power cable here, and the male end into a properly grounded outlet.
19 Top Features 1 Power Button Use this button to turn the power on and off when the Main Power Switch is on and the LCD projector is in standby. 2 Menu Button Displays the on- screen menu. 3 Select (▲▼§ ©) / (+)(–) Buttons Select: (▲▼§ ©) (+)(–): After you press the “Menu” button, use the ▲ or ▼ button to select the menu icon of the item you wish to adjust. Use these buttons while you' re in the Image Adjust mode to change the level of a selected menu item.
21 Terminal Panel Features This panel is located on the left side and is where you connect your cables. 1 S-Video Input 1 Here is where you connect the S-Video input from an external source like a VCR. Left Channel/Mono Audio Input Jack This is your left channel audio input for stereo sound coming from S-Video equipment or audio system. This also serves as your monaural audio input.
23 5 RGB Input 2 Connector (Mini D-Sub 15 pin) Connect a Macintosh or compatible computer here using the signal cable and the monitor adapter that is supplied. Or connect your PC or other RGB equipment such as IBM or compatible computers. Use the signal cable that is supplied to connect to a PC.
25 Remote Control Features You can use your remote control with the cable or wireless to operate your MultiSync MT830+/MT1030+/MT1035+ LCD Projector. With the mouse output port connected to your computer, you can also use the projector's remote control to operate your computer's mouse wireless. (See pages 59 and 60 to connect your computer to the mouse output port.
27 11 Laser Button Press and hold this button to activate the laser pointer. When lit, you can use the laser to draw your audience's attention to a red dot that you can place on any object within 30 feet (10 m). 12 Menu Button Use this button to call up the On-Screen Menu so you can adjust and set the image. After you press this button, it will light up. During this time you can use the mouse pad and right/left click buttons to make menu selections.
29 19 Slide Button Press (+) to advance the next file or slide and (-) to return to the previous file or slide. (the optional MT Viewer board required) 20 Magnify Button Use the (+) or (-) button to adjust the image size up to 400%. When the Pointer is displayed, the magnified image is displayed at the center of the Pointer. When the Pointer is not displayed, the magnified image is displayed at the center of the screen.
2 I N S T A L L A T I O N 31 This section describes how to set up your MultiSync MT830+/MT1030+/ MT1035+ LCD projector and how to connect video and audio sources. Setting Up Your MultiSync MT830+/MT1030+/ MT1035+ LCD Projector Attaching the lens cap to the lens hood with the supplied string and rivet. Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector is simple to set up and use. But before you get started, you must first: 1. Determine the image size 2.
33 Using A Tabletop Or Cart 1. Place your LCD projector on a flat level surface at the optimal distance from the screen or wall so you realize the size image you want. (Avoid having bright room lighting or sun light directly on the screen or wall where you'll be projecting the image.) (A) Top view screen 2. Connect the power cable, remove the lens cap and turn the projector on. (If no input signal is available, the projector will display a background image.) 3.
35 Distance Chart MT830+/MT1030+ Formulas(mm) H (mm) =Horizontal Screen Width M=1.25H/33.02(Projection magnification) A=C/cosα C (WIDE)=53.22M-85.609 C (TELE)=C(WIDE)21.3055 D ={(3H/8)-(92.2+8M)} =1.906M-92.2 E=92.
37 MT830+/MT1030+ Standard Zoom Lens (Wide) α β (sin= α) γ (cos= α) Degree 9.0 0.16 0.99 8.9 0.15 0.99 8.8 0.15 0.99 8.8 0.15 0.99 8.8 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.
39 MT1035+ Standard Zoom Lens (Wide) α β (sin= α) γ (cos= α) Degree 9.3 0.17 0.99 9.1 0.17 0.99 9.1 0.17 0.99 9.0 0.17 0.99 9.0 0.16 0.99 9.0 0.16 0.99 9.0 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.
41 WARNING • α F B A Ceiling Installation C A: B: C: F: Only use your LCD projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged. • Do not use the LCD projector where temperatures vary greatly. The projector must be used at temperatures between 32˚F (0˚C) and 104˚F (40˚C). • Do not expose the LCD projector to moisture, dust, or smoke. This will harm the screen image.
43 MT830+/MT1030+ Standard Zoom Lens (Wide) α β (sin= α) γ (cos= α) Degree 9.0 0.16 0.99 8.9 0.15 0.99 8.8 0.15 0.99 8.8 0.15 0.99 8.8 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.7 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.99 8.6 0.15 0.
45 MT1035+ Standard Zoom Lens (Wide) α β (sin= α) γ (cos= α) Degree 9.3 0.17 0.99 9.1 0.17 0.99 9.1 0.17 0.99 9.0 0.17 0.99 9.0 0.16 0.99 9.0 0.16 0.99 9.0 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.99 8.9 0.16 0.
47 If your projector is mounted on the ceiling and your image is upside down, use the “Menu” and “Select” buttons on your projector cabinet or (▲) (▼) buttons on your remote control to correct the orientation. (See page 74.) Reflecting The Image Using a mirror to reflect your LCD projector's image enables you to enjoy a much larger image. Contact your NEC dealer if you need a mirror.
49 Wiring Diagram To video, S-video, and audio inputs on the LCD Projector.
51 Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT830+ (SVGA) /MT1030+ and MT1035+ (XGA) Projector will enable you to project your computer's screen image for an impressive presentation.
53 Examples of DIP switch setting 13” fixed mode 17” multi-scan mode ON ON → → → ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VGA/SVGA mode 1 2 3 4 5 6 7 8 NOTE: Refer to your computer's owner's manual for more information about your computer's video output requirements and any special identification or configuring your projector's image and monitor may require.
55 Changing Video Resolutions Depending on your computer's graphic capability, you may be able to select one of several resolutions. Generally a computer- either a PC or Macintosh- with 1 meg. of memory will run: 6402480 at 16.7 million colors (24 bit Truecolor) 8002600 at 65 thousand colors. 10242768 at 256 colors. As the resolution increases, the number of colors you can run decreases. With 2 meg. of memory a computer will run: 6402480 at 16.7 million colors (24 bit Truecolor). 8002600 at 16.
57 Connecting Your Document Camera You can connect your MultiSync MT830+/MT1030+/MT1035+ LCD Projector to a document camera. To do so, simply: 1. Turn off the power to your LCD projector and document camera. 2. Use a standard video cable to connect your document camera to the Video input on your projector. 3. Turn on the LCD projector and the document camera. NOTE: Refer to your document camera's owner's manual for more information about your camera's video output requirements .
59 Connecting Your Computer to the Mouse Output Port The built-in remote mouse receiver enables you to operate your computer's mouse functions from the NEC MultiSync MT830+/ MT1030+/MT1035+ remote control. It is a great convenience for clicking through your computer-generated presentations. To connect the mouse output port: 1. Turn off your computer. 2. For PCs: Remove your current mouse and connect the serial cable from the mouse output to your PC's mouse port.
3 O P E R A T I O N 61 This section describes how to select a computer or video source and how to adjust the picture and sound. General Controls Before you turn on your MultiSync MT830+/MT1030+/ MT1035+ LCD Projector, ensure that the computer or video source is turned on and that your lens cap is removed. 1. Turn On The LCD Projector The main power switch is on the front panel of the MultiSync MT830+/MT1030+/MT1035+ LCD Projector.
63 Using The Menus RGB Auto Mode ON RGB Auto Mode OFF ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ VIDEO ○ ○ ○ ○ ○ ○ ○ 1. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu. 2. Press the "Select" button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the menu for the item you want to adjust. 3. Press the "Enter" button on the projector cabinet or the "Left Click" button on the remote control to select a submenu or item. 4.
65 Menu Descriptions & Functions Source Menu Enables you to select a video source such as a VCR, DVD player, laser disc player, computer or document camera depending on what is connected to your inputs. Press the "Select" button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the menu for the item you want to adjust Video Selects what is connected to your Video input-VCR, laser disc player, DVD player, or document camera.
67 Image Adjustment Menu Provides access to controls for your image and sound. Use the “Select” button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the menu for the item you want to adjust. The volume, image mode, keystone, brightness, contrast, color, tint and sharpness controls are available for Video or S-Video sources. The volume, image mode, keystone, brightness, contrast, white balance and auto mode controls are available for RGB 1 or RGB 2 sources.
69 White Balance... Use the Mouse pad (+) or (-) buttons to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the screen; Contrast for each color (RGB) to adjust the white level of the screen. Auto Mode ... Use the Mouse pad (+) button to turn this feature on so "Horizontal Position", "Vertical Position", "Picture Adjustment", "Fine Picture" and "Resolution" are made automatically. Usually set to ON.
71 Power Menu Provides access to Lamp Usage information and the Auto Start and Power Management features. Use the “Select” button on the projector cabinet or (▲) (▼) buttons on your remote control to access a submenu. Then press the Mouse pad (+) or (–) to choose a specific option. Lamp Usage This tells you how long the lamp has been in operation. It is recommended that you replace a lamp after 2000 hours of service.
73 Settings Menu Enables you to set preferences and other operating options. Use the “Select” button on the projector cabinet or (▲) (▼) buttons on your remote control to access the submenu you want. Capture (with the optional viewer board installed only) When Capture is selected, press "Enter" on the projector cabinet or Left Click button on the remote control to display "Execute" and "capture" an image from a source that is currently being displayed.
75 Using the Viewer function If you use the Viewer function on the LCD projector, you must first install the optional MT Viewer board (VK-MT) in the LCD projector and set up the exclusive software included with the VK-MT kit. See the user's manual included with the VK-MT for installing and uninstalling the software. 2. Remove the two screws from the bottom. Mounting the Optional MT Viewer Board To install the Viewer board: 1. Set the LCD projector on end with the carrying handle up.
77 Projecting Slides To Project the Slides (the presentation materials) 1. Insert a flash memory card into the PC card slot. * To eject the flash memory card, press the Eject button. NOTE: Should the card be difficult to insert, do not forcefully push the card in. 2. Select the PC card as a source. * Press the Menu button on the remote control or projector cabinet and select "PC CARD" from the Source menu.
79 Selecting a File from a List of Files * The Viewer feature allows you to store one or more presentation materials in a single flash memory card. Each material is referred to as a "file" or "slide". To select a file from a list of files 1. Press the Menu button on the remote control or cabinet to select "PC Card". 3.
81 Switching Slides Capturing the currently displayed screen image To switch slides, press "SLIDE +" or "SLIDE -" button. This will cancel the Auto Play mode. To set the Auto Play mode, press the Menu button to select “Start” from the Source menu and press the Enter button on the cabinet or the Left Click button on the remote control. This is valid only when the Auto Play mode is selected. See more information about “Auto Play mode” for the Help file included with the Viewer board.
4 M A I N T E N A N C E 83 This section describes the simple maintenance procedures you should follow to replace the lamp, clean or replace the filter, and replace the batteries in the remote control. Replacing The Lamp Step 1A After your lamp has been operating for 2000 hours or longer, the “status” light in the cabinet will go on. Even though the lamp may still be working, replace it at 2000 hours to maintain optimal projector performance.
85 Cleaning Or Replacing The Filter The air-filter sponge keeps the inside of the MultiSync MT830+/MT1030+/MT1035+ LCD Projector free from dust or dirt and should be cleaned after every 100 hours of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat. NOTE: Clean your filter after every 100 hours of operation. CAUTION • • • • Turn off the main power and unplug the projector before replacing the filter.
87 Cette section décrit les procédures simples d’entretien que vous aurez à suivre pour remplacer la lampe, nettoyer ou remplacer le filtre et remplacer les piles de la télécommande. Remplacement de la lampe Lorsque la lampe a été utilisée pendant 2000 heures ou plus, le voyant “Status” (état) du coffret s’allume. Même si la lampe peut encore fonctionner, remplacez-la au bout de 2000 heures pour conserver une performance optimale de votre projecteur.
89 Nettoyage ou remplacement du filtre Le coussin éponge du filtre à air maintient l’intérieur du projecteur à affichage à cristaux liquides MultiSync MT830+/MT1030+/MT1035+ à l’abri de la poussière ou de la saleté et doit être nettoyé toutes les 100 heures d’utilisation (plus souvent dans les endroits poussiéreux). Si le filtre est sale ou bouché, le projecteur risque de surchauffer. REMARQUE: Nettoyez le filtre toutes les 100 heures d’utilisation.
5 T R O U B L E S H O O T I N G 91 This section helps you resolve problems you may encounter while setting up or using your MultiSync MT830+/MT1030+/MT1035+ LCD Projector. Status Light Messages Status Condition 47 OFF m Normal On continually m The projector lamp has exceeded 2000 hours of operation and should be replaced. Blinking very rapidly (On and off in a cycle of 1 sec.) m Either the lamp cover or filter cover is not fastened properly. Check each and reattach them if necessary.
93 Common Problems & Solutions Problem Check These Items Does not turn on • Check that the cord is plugged in and that the power switch on the front panel is on. • Ensure that the filter cover is installed correctly. (See page 86 or 90.) • Check to see if the projector has overheated or the lamp usage exceeds 2100 hours. If there is insufficient ventilation around the projector or if the room where you're presenting is particularly warm, move the projector to a cooler location.
6 S P E C I F I C A T I O N S 95 This section provides technical information about the MultiSync MT830+/MT1030+/MT1035+ LCD Projector's performance. Optical LCD Panel 1.3", p-Si TFT active-matrix, 8002600 dot (MT830+) / 10242768 dot (MT1030+ / MT1035+) With Micro Lens Array (MT1035+) Lens Power zoom, power focus F 2.5 f = 52 – 68 mm (MT830+ / MT1030+) F 2.
16.24" (412.0) MT1035+ 15.6" (396.0) MT830+ / MT1030+ + STATUS POWER – RGB INPUT 1 RGB MONITOR OUTPUT AUDIO AUDIO INPUT 2 PC CONTROL MOUSE OUTPU RGB TPUT AUDIO REMOTE CONTROL INPUT 3.63" (92.2) 14.9" (378.0) – ON/OFF R AUDIO L/MONO AUDIO R INPUT L/MONO S–VIDEO INPUT VIDEO 98 SPECIFICATIONS 50 AC IN 5.8" (148.0) 97 Cabinet Dimensions 11.4" (290) 7" (178.5) 13.
99 D-Sub Pin Assignments PC 15-Pin mini D-Sub Pin No.
101 Timing Chart 52 Y/N Signal Resolution 6402480 7682576 7682576 6402350 6402400 6402400 6402400 6402480 6402480 6402480 6402480 6402480 6402480 6402480 6402480 6402480 7202350 7202400 7202400 7202350 Refresh Rate (Hz) 60 50 50 85.08 70 85.08 66 59.94 60 60 66.7 66.67 72.81 75 75 85.01 70.09 70.09 85.04 87.85 F.H. (kHz) 15.734 15.625 15.625 37.86 31.47 37.86 35 31.47 31.47 31.47 34.97 35 37.86 37.5 39.375 43.269 31.469 31.4469 37.927 39.44 Dot Clk(MHz) 31.5 25.175 31.5 30.24 25.175 25.175 25.175 31.
103 PC Control Command Reference Command Codes 53 No.
105 Command Codes (continued) No.
107 Cable Connection Communication Protocol Baud rate: 9600 bps Data length: 8 bits Parity: No parity Stop bit: One bit X on/off: None Full duplex Communications procedure: If the CPU of the LCD projector has received the data correctly, it returns an ACK(C5H).
