Specifications

English-28
Specifi cations
Monitor Specifi cations MD302C6 Notes
LCD panel color Clear Base
LCD 30.0-inch (76.8 cm), color, TFT, Active matrix type, normally black Anti-glare
Pixel pitch (H x V) 0.197 x 0.197 mm
Display area (H x V) 645.5 x 403.05 mm
Pixel (H x V) 3280 x 2048
Display colors 8 bit:16.77 million out of 68 billion*
10 bit: 1.07 billion out of 68 billion*
Backlight LED backlight
LCD Optical characteristics (typ.) Viewing angle: 170° horizontal/vertical (contrast ratio ≥ 10:1)
Contrast ratio: 1000:1 (Viewing angle of 0° horizontal and vertical)
Luminance DICOM calibrated 400 cd/m
2
as factory default
Maximum 550 cd/m
2
(800 cd/m
2
typ. as LCD component)
Input sync signal DVI 1.0 compliant, DisplayPort 1.1a compliant
Available resolution 640 x 480
800 x 600
1024 x 768
1536 x 2048 (at Fv=60Hz), 3072 x 2048 (at Fv=30Hz)
1640 x 2048 (at Fv=60Hz), 3280 x 2048 (at Fv=30Hz)
Input connectors DVI 24-pin connector (x2), DisplayPort connector (x2)
Power Supply AC 100-240 V ~ 50/60 Hz
Current Rating 4.0 - 1.67 A
USB Hub USB Rev. 2.0 compliant, Self-powered
USB upstream port (x1), USB downstream ports (x2)
Ambient conditions Temperature:
Humidity (no condensation):
Air pressure:
Operating: 5 - 35°C, Transport / Storage: -20 - 60°C
Operating: 20 - 80%, Transport / Storage: 10 - 85%
Operating: 700 - 1060hPa, Transport / Storage: 266 - 1060hPa
Dimensions & weight Net: 695.6 x 486.5 - 618.2 x 301.6 mm (W x H x D) approx. 17.6 kg (38.8 lbs)
27.4 x 19.2 - 24.3 x 11.9 inches (W x H x D)
Safety certifi cations ANSI/AAMI ES60601-1:2005+A1 (2012), CAN/CSA-C22.2 No. 60601-1:08, FCC-B, ICES-003-B,
CE-MDD, VCCI-B, FDA510(K)
*1 billion = 10
9
NOTE: Technical specifi cations are subject to change without notice.
MD302C6 is intended to be used in rooms with less than 50 to 69.7 lx ambient light.
The maximum ambient light level depends on technical QA standards and/or national obligations.
Troubleshooting
The display won't turn on! (The power indicator is off.)
• Make sure the display is connected to the power outlet.
• Check to see if the display is turned on.
The screen is not lit!
• Check if cables are connected correctly.
• Check if the computer is turned on.
• If the LED indicator is orange, the computer may be in energy saving mode. Press any key on the keyboard to wake up
the computer.
• The input signal frequency or display resolution may not be appropriate for the display. Refer to the computer instruction
manual and adjust the frequency and/or resolution.
• If the LED is red, this may be an error indication. Contact your supplier.
Images are not displayed properly!
• The display resolution may not be appropriate for the display. Refer to the computer instruction manual and adjust the
resolution.
The refresh rate is set to 60Hz (dual-link mode) and resolution loss (scan line gaps) occurs!
• This can happen when a DVI Single Link cable or a DisplayPort to DVI Single Link adapter is used. Use the supplied
dual-link cable which supports both single-link (30Hz) and dual-link (60Hz) modes, or set the refresh rate to 30Hz.