MD215MG
Disclaimer * Windows and MS-DOS are trademarks and/or registered trademarks of Microsoft Corporation in the United States and/or other countries. * VESA is a trademark of the Video Electronics Standard Association. * All other products and company names are trademarks of their respective owners.
English
Registration Information ...............................................................................................................English-2 Intended Use ................................................................................................................................English-4 Recommended use ......................................................................................................................English-5 Contents ..............................................................
Registration Information Declaration Declaration of the Authorized Representative NEC Display Solutions Europe GmbH declares that the product listed is in conformity with the essential requirements and provisions of the Council Directive 93/42/EEC, including the amendments of the Council Directive 2007/47/EC, and conforms to the applicable clauses of the following standards: Means of Conformity Device Classification: Class I, non-measuring function Applicable Rules: Annex IX, Rules 1.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Intended Use The MD215MG grayscale display is intended to be used for displaying and viewing of digital images for diagnosis, including digital mammography, by trained physicians. Caution: The MD215MG grayscale display cannot be used for a life-support system. This device is designed as component of a final system which is in compliance to IEC60601-1-1 requirements. Safety Precautions This device is designed for exclusive interconnection with IEC60601-1 certified equipment outside of patient vicinity.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD GRAYSCALE MONITOR: • DO NOT OPEN THE MONITOR OR AC ADAPTER. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm (15.75 inches) and no further away than 70 cm (27.56 inches) from your eyes.
English Contents Your new NEC monitor box* should contain the following: • MD215MG monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (DVI-D to DVI-D cable)*1 • AC adapter MW122 • USB Cable • Quick Reference Guide Power Cord*2 AC adapter MW122 Quick R eferenc e Guide Quick Reference Guide USB Cable DVI-D to DVI-D cable*1 * Remember to save your original box and packing material to transport or ship the monitor. *1 Dual link DVI cable.
Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a display controller that can output a resolution of 2048 x 2560 is needed. 1. Turn off the power to your computer. 2. For a PC with DVI digital output: Connect the DVI signal cable to the connector of the display controller in your system (Figure A). Tighten all screws. Figure A 3. Remove the cable cover (Figure B).
Place the cables in the hooks firmly and evenly (Figure D). Figure D 6. Slide down the cable cover (Figure E). 7. Please check that you can still rotate, raise and lower the monitor screen, when you have installed the cables. NOTE: Handle with care when raising, lowering, rotating or tilting the monitor screen. 8. Connect the AC adapter with the proper AC cord, then plug the AC cord to the power outlet.
Controls 1 Power Switch To turn the monitor on and off. 2 LED Indicates that the power is on. Turns off automatically, when the luminance is stabilized. 3 Front Sensor For luminance stabilization and calibration. 4 Ambient Light Sensor Measures ambient light during calibration process. 5 + (plus) Button To open the OSD (On Screen Display) 1st click – Display information 2nd click – Present operating state 3rd click – OSD off (otherwise OSD disappears in 15 sec.
Monitor Specifications MD215MG LCD panel color Clear Base Notes LCD 21.3-inch (54 cm), monochrome, TFT active matrix, anti-glare Pixel pitch (H x V) 0.165 x 0.165 mm Display area (H x V) 337.9 x 422.
Additional Installation Information Advanced OSD Several control functions are available by entering the advanced OSD. These control functions are additional OSD menu items, which are always accessible after opening the standard OSD.
4. Click the (+) plus button or (-) minus button once to close the “INFORMATION” OSD. NOTE: When using the “Portrait” setting, the display controller does not need to rotate the image in the video ram. In most applications, this setting is preferable. However, if there is a need to rotate the image by the display controller, the “Landscape” setting may be preferable. How to Change the Display Mode (Normal/Packed Pixel) 1.
How to Change Configuration (Preset 1, 2, 3) The NEC model MD215MG is shipped with 3 factory preset configurations, as listed below. Configuration 1 2 3 Maximum 400 430 500 Luminance (cd/m2) Minimum 1.0 1.5 1.0 Ambient 0.0 0.0 0.0 Gamma Remark DICOM DICOM DICOM [Factory Default] The configuration can be changed via an OSD menu. These parameters may be modified anytime by a new display calibration. Regarding display calibration, please refer to the MD215MG Calibrator Manual. 1.
English Advanced OSD Controls without video input If no video signal is available, the display enters the power save mode and the OSD cannot be displayed. In this case, please follow the procedure below. 1. Confirm that the display is in power save mode and the LED next to the power switch is lit orange. If the LED is off, please push the power switch to turn on the monitor. 2. Hold down the (+) plus button and the (-) minus button simultaneously for over 2 seconds.
Antitheft Security Slot The display is equipped with the security slot supported by MicroSaver Security Lock System by Kensington Technology Group. The MicroSaver locks are available at PC supply stores. Note: Kensington is the registered trademark of Kensington Technology Group.
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization).
NEC Display Solutions, Ltd. 4-28, Mita 1-chome, Minato-ku, Tokyo, Japan NEC Display Solutions of America 500 Park Blvd. Suite 1100 Itasca, Illinois 60143 USA Phone: 630.467.3000 Fax: 630.467.3010 NEC Display Solutions Europe GmbH Landshuter Allee 12-14 D-80637 Muenchen Germany Phone: +49(0)89/99699-0 Fax: +49(0)89/99699-500 Vol.
