MD211G5
Disclaimer * Windows and MS-DOS are trademarks and/or registered trademarks of Microsoft Corporation in the United States and/or other countries. * VESA is a trademark of the Video Electronics Standard Association. * All other products and company names are trademarks of their respective owners.
English
Registration Information ...............................................................................................................English-2 Intended Use ................................................................................................................................English-4 Recommended use ......................................................................................................................English-5 Contents ..............................................................
Registration Information Declaration Declaration of the Authorized Representative NEC Display Solutions Europe GmbH declares that the product listed is in conformity with the essential requirements and provisions of the Council Directive 93/42/EEC, including the amendments of the Council Directive 2007/47/EC, and conforms to the applicable clauses of the following standards: Means of Conformity Device Classification: Class I, non-measuring function Applicable Rules: Annex IX, Rules 1.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION THIS APPARATUS MUST BE EARTHED BECAUSE OF CLASS I EQUIPMENT. TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Intended Use The MD211G5 grayscale display is intended to be used for displaying and viewing of digital images for diagnosis, including digital mammography, by trained physicians. Caution: The MD211G5 grayscale display cannot be used for a life-support system. This device is designed as component of a final system which is in compliance to IEC 60601-1-1 requirements. Contraindications: None known.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD GRAYSCALE MONITOR: WARNING: Do not modify this equipment without authorization of the manufacturer. WARNING: To disconnect this product from the mains supply disconnect the mains plug from the socket outlet. WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: No modification of this equipment is allowed.
Image Persistence: Image persistence exists, when a residual or “ghost” image of a previous image remains visible on the screen. Unlike with CRT monitors, image persistence on LCD monitors is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed.
English Contents Your new NEC monitor box* should contain the following: • MD211G5 monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (DVI-D to DVI-D cable)*1 • DisplayPort cable • USB Cable • Quick Reference Guide Power Cord*2 DisplayPort cable Quick R eferenc e Guide Quick Reference Guide USB Cable DVI-D to DVI-D cable*1 * Remember to save your original box and packing material to transport or ship the monitor. *1 Dual link DVI cable.
Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a display controller that can output a resolution of 2048 x 2560 is needed. 1. Turn off the power to your computer. 2. For a PC with DVI digital output: Connect the DVI signal cable to the connector of the display controller in your system (Figure A.1). Tighten all screws.
Place the cables in the hooks firmly and evenly (Figure D). Figure D 6. Slide down the cable cover (Figure E). 7. Please check that you can still rotate, raise and lower the monitor screen, when you have installed the cables. NOTE: Handle with care when raising, lowering, rotating or tilting the monitor screen. 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.
Controls 1 Power Switch To turn the monitor on and off. 2 LED Indicates that the power is on. Turns off automatically, when the luminance is stabilized. 3 Front Sensor For luminance stabilization and calibration. 4 Ambient Light Sensor Measures ambient light during calibration process. 5 + (plus) Button To open the OSD (On Screen Display) 1st click – Display information 2nd click – Present operating state 3rd click – DICOM conformance test 4th click – OSD off (otherwise OSD disappears in 15 sec.
Monitor Specifications MD211G5 LCD panel color Clear Base Notes LCD 21.3-inch (54 cm), monochrome, TFT active matrix, anti-glare Pixel pitch (H x V) 0.165 x 0.165 mm Display area (H x V) 337.9 x 422.4 mm Pixel (H x V) 2048 x 2560 Grayscale 256 steps of gray out of a palette of 12277 Backlight Edge Light Type with white LED Viewing angle: 176° horizontal/vertical (contrast ratio ≥ 50:1) LCD Optical characteristics (typ.
Additional Installation Information Advanced OSD Several control functions are available by entering the advanced OSD. These control functions are additional OSD menu items, which are always accessible after opening the standard OSD.
4. Click the (+) plus button or (-) minus button once to close the “INFORMATION” OSD. NOTE: When using the “Portrait” setting, the display controller does not need to rotate the image in the video ram. In most applications, this setting is preferable. However, if there is a need to rotate the image by the display controller, the “Landscape” setting may be preferable. Switching input source Please operate input source change following the procedure mentioned below. 1.
How to Change Configuration (Preset 1, 2, 3) The NEC model MD211G5 is shipped with 3 factory preset configurations, as listed below. Configuration 1 2 3 Maximum 500 550 400 Luminance (cd/m2) Minimum 1.0 1.0 1.0 Ambient 0.0 0.0 0.0 Gamma Remark DICOM DICOM DICOM [Factory Default] The configuration can be changed via an OSD menu. The configuration 1 parameters may be modified anytime by a new display calibration. Regarding display calibration, please refer to the GammaCompMD QA Manual. 1.
This function is available only when the display has been calibrated to DICOM GSDF. Performing the DICOM conformance test ensures DICOM conformance of the display by measuring and checking the display properties. The DICOM conformance test is recommended to be performed after 60 minutes of continuous lighting time of the backlight of the LCD panel. If the test is performed in less than 60 minutes of lighting time, a margin of measurement error may be larger because luminance is not stable enough.
4. Showing the test results When the measurement is completed, the test results are shown. Test results A. Test results Passed: Max. deviation ≤ 10% Failed: Max. deviation > 10% Canceled: Test has been canceled. Passed(!), Failed(!) “(!)” following Passed and Failed indicates that the recommended condition has not been met. (The test was performed in less than 60 minutes of continuous lighting time of the backlight.
The tilt and swivel stand, as shipped with the display, is interchangeable with commercially available wall mounts or multi-display mounting arms that: • Come with a mount plate with 4 slotted screw holes at 100 mm x 100 mm and • Can bear the total weight of the LCD panel (without the stand) and the cables connected to it. For more information ask your mounting arm supplier. Note: Use the original screws to use the LCD panel back on its original tilt stand.
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization).
NEC Display Solutions, Ltd. 4-28, Mita 1-chome, Minato-ku, Tokyo, Japan NEC Display Solutions of America 500 Park Blvd. Suite 1100 Itasca, Illinois 60143 USA Phone: +1-630.467.3000 Fax: +1-630.467.3010 NEC Display Solutions Europe GmbH Landshuter Allee 12-14 D-80637 Muenchen Germany Phone: +49(0)89/99699-0 Fax: +49(0)89/99699-500 Vol.
