Startup Guide

Express5800/R120f-2M
First Edition,
September 2014
Be sure to read this guide carefully before using this
server and retain it for reference.
This document provides information required to use your server safely and properly.
Keep this document nearby so that you may refer to it as necessary. Before using this server, be sure to read
this guide and “User’s Guide” (in the DVD provided with this server). For details of names in this document,
refer to Names and Functions of Parts in the “User’s Guide”.
The following describes the procedures from opening the carton box to
starting using this product. Be sure to follow these steps.
Step 1
Check the accessories.
Open the carton box, and then make sure you have all the accessories listed below:
●
Express5800/R120f-2M server × 1
●
Slide rail (outer rail) × 2
●
EXPRESSBUILDER × 1
●
Slide rail (inner rail) × 2
●
Getting Started (This guide) × 1
●
Screws for internal backup devices × 6
●
Safety Precautions and Regulatory Notices × 1
●
Front Bezel
●
SAS/SATA cable (when RAID controller is not installed)
●
Security key (attached to Front Bezel)
Important: Keep the accessories in a safe place.
Step 2
Install internal optional devices.
Install internal optional devices. (Go to Step 3 if you have not purchased options.)
Note: See Installing Internal Optional Devices in the “User’s Guide” and the guide provided with
the optional device.
Step 3
Place the product to a proper location.
Determine the location to place this product.
Set up a rack in an appropriate place, and then mount the server in the rack.
Note: See Proper Location and Connection in the “User’s Guide”.
Step 4
Connect cables.
Connect the cables to the server.
Note: See Proper Location and Connection in the “User’s Guide”.
*1 Connect the power cord to a circuit breaker of up to 15 A.
*2 Either one can connect with a display unit.
Getting Started!
• Keep proper posture • Adjust the angle, brightness, and contrast of the
display to suit your preferences.
Tips for your health and safety
Using a computer extensively may affect different parts of you r body. Here are tips you should
follow while working on a computer to minimize strain on your body.
•Take a break. Light exercise is also recommended.• Adjust the angle of keyboard
The environment that satisfies the
following conditions
<Operating>
Ambient temperature:
10˚C to 35˚C/10˚C to 40˚C
Humidity: 20% to 80%
Temperature gradient: ±10˚C/hour
Air pressure: 749 to 1040 hpa
<Storage>
Ambient temperature:
5˚C to 40˚C
Humidity: 10% to 80%
Temperature gradient: ±15˚C/hour
Air pressure: 749 to 1040 hpa
Outlet or UPS within
reach of the provided cord
Outlet or UPS equipped
with AC 100V/200V and
parallel bipolar ground
On the fla
t and robust board
Do not use in the environment where
corrosive gas is generated.
There must be 1 m clearance in
front and behind the unit, 60 cm
on each side, and 40 cm above.
When installing
multiple racks,
be sure to
anchor them
together.
Attach stabilizers.
M
1 2 3 4
Instruction Manuals
To see User’s Guide in EXPRESSBUILDER, follow the steps below.
(1) Turn on a computer on which Windows was installed.
(2) Insert the attached EXPRESSBUILDER DVD into the computer.
The following menu automatically appears.
(3) Click Instruction Manuals on the menu.
USB device
FRONT
Display unit*
2
10GBASE-SFP/
10GBASE-T/
1000BASE-T/
100BASE-TX/
10BASE-T
Finally, connect the
provided power cord
to an outlet. *
1
REAR
Hub, switching hub, etc.
Device with serial interface
Management LAN port
100BASE-T/
10BASE-T
Data LAN port
Display unit*
2
USB device