User Guide

raidcmd
2
>
d th
e result of Initialize by "oplist" and "property"
commands.
5
Do y
ou continue ? [yes(y) or no(n)] : yes
Initialize all of Logical Drive after creating them. You can
see the progress an
Run the above configuration.
,Logical Drive capacity is decided by the smallest Physical
Device of capacity.
Create Logical Drive #2 with different Physical Devices of
a capacity. Therefore
<Caution>
PD e252s7 [Online] SATA-HDD(SSD)
PD e252s6 [Online] SATA-HDD(SSD)
Disk Array #3
LD #3 [Online] RAID 1
PD e252s1 [Online] SATA-HDD
PD e252s0 [Online] SATA-HDD
LD #2 [Online] RAID 1
Disk Array #2
PD e252s5 [Dedicated Hot Spare] SAS-HDD
PD e252s4 [Online] SAS-HDD
PD e252s3 [Online] SAS-HDD
LD #1 [Online] RAID 5
PD e252s2 [Online] SAS-HDD
RAID Controller #1(0) LSI MegaRAID SAS 9267-8i
Disk Array #1
Step 3/3 : Confirm the contents of configuration
Do you continue ? [yes(y) or no(n)] : y
Creating Logical Drive count [ 1] : 1
Maximum Logical Drive count : 1
Do you continue ? [yes(y) or no(n)] : y
Hot Spare count : 0
Physical Device count using Logical Drive(s) [ 2] : 2
<Physical Device (Type : SATA-HDD(SSD))>
Unused Physical Device count : 2
Do you continue ? [yes(y) or no(n)] : y
Maximum Logical Drive count : 1
Creating Logical Drive count [ 1] : 1
Do you continue ? [yes(y) or no(n)] : y
Hot Spare count : 0
Physical Device count using Logical Drive(s) [ 2] : 2
<Physical Device (Type : SATA-HDD)>
Unused Physical Device count : 2
Do you continue ? [yes(y) or no(n)] : y
Creating Logical Drive count [ 1] : 1
4
Maxi
mum Logical Drive count : 1
Do you continue ? [yes(y) or no(n)] : y
Hot Spare count : 1
Physical Device count using Logical Drive(s) [ 2- 4] : 3
<Physical Device (Type : SAS-HDD)>
Unused Physical Device count : 4
RAID Controller #1 LSI MegaRAID SAS 9267-8i
RAID Controller [1] :1
Step 2/3 : Set the contents of configuration
3
Step
1/3 : Select RAID Controller
> raidcmd econfig
Step 1 Connect Physical Devices used for Easy
Configuration to the RAID Controller before executing
raidcmd if required.
Step 2 Execute "econfig" command.
Step 3 Specify the conditions on Easy
Configuration.
In step 1/3, select the RAID Controller to be configured.
Enter the RAID Controller number to be configured.
Step 4 In step 2/3, specify the number of Physical
Devices used for Logical Drive(s) ("Physical Device
count using Logical Drive(s)") and the number of
Logical Drives to be created in the RAID Controller
("Making Logical Drive count"). If Physical Devices of
different Interface Types or Device Type exist, specify
the number of Physical Devices in each type (in the
example shown to the right, proper settings are provided
for Physical Devices of the SAS interface. If other
Physical Devices of different types exist, perform the
operation in each type).
Step 5 Step 3/3 shows the configuration of the
RAID System to be configured by the Easy
Configuration. To configure the RAID System
according to the displayed information, type "yes". To
change the configuration, type "no".
If you type "yes", the raidcmd executes the
configuration of the RAID System. After the easy
configuration is finished successfully, raidcmd
terminates normally. Making Logical Drives and Hot
Spares is now completed. See the property of each
component to check the configuration. However, the
Initialize of the Logical Drives having been created may
not be completed. The progress of initializing the
Logical Drives can be checked by using "oplist"
command. The result of initializing the Logical Drive
can be checked by RAID Log.
70