Front Cover Installation Guide Express5800 Series NEC ESMPRO Agent Extension Chapter 1 Summary Chapter 2 System Requirements Chapter 3 Installation Chapter 4 Precautions for Use Rev.2.
NEC ESMPRO Agent Extension Installation Guide Contents Front Cover ....................................................................................................................................................... 1 Contents............................................................................................................................................................. 2 Trademarks ...............................................................................................................
NEC ESMPRO Agent Extension Installation Guide Trademarks NEC ESMPRO and EXPRESSBUILDER are trademarks of NEC Corporation. Microsoft, Windows, Windows Vista and Windows Server are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Linux is the registered trademark of Linus Torvalds in the U.S. and other countries. Red Hat is registered trademarks of Red Hat, Inc. and its subsidiaries in the United States and other countries.
NEC ESMPRO Agent Extension Installation Guide External Libraries which this product uses This product contains libraries ("External Libraries") provided by the third party suppliers ("Suppliers"). Please assume and agree these libraries' license documents and NOTICE files before using this product. License documents and NOTICE files of "External Libraries" are stored in the following folders.
NEC ESMPRO Agent Extension Installation Guide About This Document This document explains the complete procedures from installation of "NEC ESMPRO Agent Extension" to setup of managed server. Before attempting to operate NEC ESMPRO Agent Extension, read this document so as to gain an adequate understanding of the contents. Notes This document is intended for persons who are familiar with the operating system's functions and operations and the network's functions and setup.
NEC ESMPRO Agent Extension Installation Guide Chapter1 Summary NEC ESMPRO Agent Extension (Ver.2) is software that works on the managed server. When "ESMPRO Management" of BMC configuration on the managed server is set "Enable", you can execute commands specified by NEC ESMPRO Manager Ver.5.4 or later. CHECK: You can configure BMC on the managed server by the following software.
NEC ESMPRO Agent Extension Installation Guide Chapter2 2.1 System Requirements Managed server Install NEC ESMPRO Agent Extension (Ver.2) in the managed server. It works on the following environment. Hardware It needs to be managed by NEC ESMPRO Manager (Ver.5.4 or later) and satisfy the following conditions. Managed Server NEC Express5800 series and NEC Storage NS series that integrates EXPRESSSCOPE Engine 3 or SP3. IMPORTANT: You can not install NEC ESMPRO Agent Extension (Ver.
NEC ESMPRO Agent Extension Installation Guide IMPORTANT: You can not install NEC ESMPRO Agent Extension in the following case. -- Installation on guest OS virtual of machine. The following packages are necessary to use NEC ESMPRO Agent Extension on Red Hat Enterprise Linux Server 6(x64) or Oracle Linux 6(x64). -- glibc i686 -- nss-softokn-freebl i686 -- libgcc i686 CHECK: Oracle Linux 6 is supported by the upper version from NEC ESMPRO Agent Extension for Linux Ver2.04.
NEC ESMPRO Agent Extension Installation Guide 2.2 Notes on Managed Servers This section explains particular notes on managed servers. 2.2.1 Teaming Setting If you set Teaming (providing redundancy or multiplexing with multiple network adapters) for LAN port that NEC ESMPRO Agent Extension uses on the managed server, please setup the NEC ESMPRO Agent Extension with the procedure below. This procedure does not depend on OS of the managed server. Set IP address that NEC ESMPRO Agent Extension uses.
NEC ESMPRO Agent Extension Installation Guide Chapter3 3.1 Installation NEC ESMPRO Agent Extension Installation for Windows Install NEC ESMPRO Agent Extension in the managed server in following order: (1) Install JRE It is necessary to install JRE before the installation of NEC ESMPRO Agent Extension. (2) Install NEC ESMPRO Agent Extension Install NEC ESMPRO Agent Extension on the managed server.
NEC ESMPRO Agent Extension Installation Guide 3.1.3 Install JRE Be sure to install JRE of the version specified in chapter 2.1. Click "Java Runtime Environment (JRE)" on the installation menu. . The "Download Files" dialog box will appear. Click [Open]. JRE installer will be started. TIPS: Depending on your environment, please substitute [Run] for [Open]. Install JRE according to the installer's instructions. 3.1.4 Install NEC ESMPRO Agent Extension Check before perform the installation.
NEC ESMPRO Agent Extension Installation Guide Enter a folder name to install. Click [Next]. Confirm the installation setting, and click [Next]. The installation will be started. When the installation is completed, NEC ESMPRO Agent Extension service is started and available. TIPS: You can confirm whether the installation of NEC ESMPRO Agent Extension is completed or not. Click "Administrative Tools" - "Services", if the Status of "ESM Agent Extension Service" is started, the installation is completed.
NEC ESMPRO Agent Extension Installation Guide 3.1.5 Set the IP Address that NEC ESMPRO Agent Extension uses Do the setting on the managed server. Click "NEC ESMPRO Agent Extension" - "NEC ESMPRO Agent Extension" from [start] on Windows to open the setting dialog box of NEC ESMPRO Agent Extension. Select IP address of Operating System that NEC ESMPRO Agent Extension uses. CHECK: Please execute [Set Agent IP address] again if you change the LAN ports or a new LAN card is inserted to the managed server.
NEC ESMPRO Agent Extension Installation Guide 3.2 NEC ESMPRO Agent Extension Uninstallation for Windows To uninstall the software, perform it in following order: Uninstall NEC ESMPRO Agent Extension Open "Add/Remove Programs" of control panel on Windows. Select NEC ESMPRO Agent Extension and click [Delete]. Uninstall it according to the on-screen instructions. CHECK: Close the dialog box of NEC ESMPRO Agent Extension if it has been opened, and then uninstall NEC ESMPRO Agent Extension.
NEC ESMPRO Agent Extension Installation Guide 3.4 NEC ESMPRO Agent Extension Installation for Linux To install the software, perform it in following order: (1) Install JRE It is necessary to install JRE before the installation of NEC ESMPRO Agent Extension. (2) Copy and extract NEC ESMPRO Agent Extension installer Copy the installer to the hard disk on the managed server and extract it. (3) Install NEC ESMPRO Agent Extension Install NEC ESMPRO Agent Extension on the managed server.
NEC ESMPRO Agent Extension Installation Guide Install JRE. JRE will be installed in the directory named JRE version under JRE/usr/java. The following is an example that the version of JRE is 7 Update7. chmod a+x jre-7u7-linux-i586.rpm rpm -ivh jre-7u7-linux-i586.rpm 3.4.3 Copy and extract NEC ESMPRO Agent Extension installer Copy NEC ESMPRO Agent Extension installer into any directory on the managed server. NEC ESMPRO Agent Extension installer files are in /esmpro_sa_ex/agt_x.
NEC ESMPRO Agent Extension Installation Guide 3.4.5 Set the IP Address of NEC ESMPRO Agent Extension uses Do the setting on the managed server. Open the setting of NEC ESMPRO Agent Extension. Do the following operation to open the setting function of NEC ESMPRO Agent Extension. /opt/nec/esmpro_sa_ex_sysman/agentconf Select IP address of Operating System that NEC ESMPRO Agent Extension uses.
NEC ESMPRO Agent Extension Installation Guide 3.5 NEC ESMPRO Agent Extension Uninstallation for Linux Login to Linux as root user. To uninstall the software, perform in following order: (1) Uninstall NEC ESMPRO Agent Extension (2) Uninstall JRE 3.5.1 Uninstall NEC ESMPRO Agent Extension Move to the directory in which all installation files are copied. cd /usr/local/bin/agt_x/EsmproSaEx-N.NN-x "N.NN" in the example directory name means the version. Execute the shell for uninstallation. .
NEC ESMPRO Agent Extension Installation Guide 3.6 JRE Update for Linux Perform in following order to update JRE software on the managed server which NEC ESMPRO Agent Extension has been installed on: This example is for updating JRE to ver.7 Update7 when you use NEC ESMPRO Agent Extension. Stop NEC ESMPRO Agent Extension service. /etc/rc.d/init.d/dianascopeagent stop Update JRE. chmod a+x jre-7u7-linux-i586.rpm rpm -ivh jre-7u7-linux-i586.rpm Start NEC ESMPRO Agent Extension service. /etc/rc.d/init.
NEC ESMPRO Agent Extension Installation Guide Chapter4 4.1 Precautions for Use NEC ESMPRO Agent Extension installation -- NEC ESMPRO Agent Extension Installer (Windows & Linux) cannot downgrade to the older version. If you want to use the older version, uninstall the current version and then install older version. Note: All the registered information will be deleted as the result of the uninstalling.
NEC ESMPRO Agent Extension Installation Guide 4.3.2 Linux Firewall in Red Hat Enterprise Linux Execute "setup" command. Select "Firewall configuration" and "Customize". Add the allowed ports as follows: Port / Port Range: 47120 - 47129 Protocol: tcp 4.3.3 Linux Firewall in SUSE Linux Enterprise Server Execute "yast" command. Select "Security and Users" and "Firewall". Select "Allowed Services" and "Advanced...". Add the allowed ports as follows: TCP Ports: 47120 - 47129 4.
NEC ESMPRO Agent Extension Installation Guide Revision History 2.00 2.01 2011/05/10 2011/06/24 2.02 2.03 2012/02/28 2012/05/25 2.04 2012/07/05 2.05 2012/08/22 2.06 2012/10/31 2.07 2013/03/12 2.08 2013/07/18 2.09 2013/09/11 2.10 2014/01/07 2.11 2014/08/19 Initial edition Adds required packages by Red Hat Enterprise Linux Server 6 (x64). Changes cover. Corrects writing errors. Corrects writing errors. Changes Installation. Corrects writing errors. Changes Installation for Linux.
NEC ESMPRO Agent Extension Installation Guide NEC ESMPRO Agent Extension Installation Guide © NEC Corporation 2011-2014 23
