Appendix B : raidcmd Command Reference This chapter describes commands of the raidcmd. cc [Overview] Starts or stops Consistency Check. [Format] raidcmd cc -c={all| -l={all|}} -op={start|stop} Command Parameter -c={all|} -l={all|} -op={start|stop} Description Specify the RAID Controller to be processed. all : all of RAID Controllers : RAID Controller Number Specify the Logical Drive to be processed.
ccs [Overview] Starts Consistency Check of Logical Drives in the RAID Controllers in which Patrol Read is disabled or not supported. [Format] raidcmd ccs [Description] Starts Consistency Check of Logical Drives in the RAID Controllers in which Patrol Read is disabled or not supported. [Condition] Allow to start Consistency Check to Logical Drive by ccs with the following situation. - RAID Controller does not have the function of Patrol Read. - Patrol Read is disabled.
delld [Overview] Deletes a Logical Drive. [Format] raidcmd delld -c= -l= [-y] Command Parameter -c= -l= [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Logical Drive to be processed. : Logical Drive Number Deletes the Logical Drive immediately without displaying the message of confirming that the Logical Drive may be deleted. [Description] Deletes the specified Logical Drive.
delscd [Overview] Deletes an SSD Cache Drive. [Format] raidcmd delscd -c= -l= [-y] Command Parameter -c= -l= [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the SSD Cache Drive to be processed. : Logical Drive Number Deletes the SSD Cache Drive immediately without displaying the message of confirming that the SSD Cache Drive may be deleted.
econfig [Overview] Configures a RAID System with a RAID Controller easily. [Format] raidcmd econfig [Description] Executes easy configuration which can automatically configure a RAID System with the specified RAID Controller. For details of the easy configuration, see "Configuring RAID System Easily" of "Universal RAID Utility User's Guide".
help [Overview] Displays the help of raidcmd. [Format] raidcmd help Command Parameter Description Specify the command name to see the help. If command name is omitted, displays the list of command. [Description] Displays the description of each command of raidcmd. If don't specify the command name as command parameter, displays the list of all of command.
hotspare [Overview] Makes or removes a Hot Spare. [Format] raidcmd hotspare -c= -p= -mr={make [-a= [,] ] | remove } [-y] Command Parameter -c= -p= -mr={make [-a=[,]] | remove} [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Physical Device to be processed.
init [Overview] Starts or stops Initialize. [Format] raidcmd init -c= -l= -op={start|stop} [-im={full|quick}] [-y] Command Parameter -c= -l= -op={start|stop} [-im={full|quick}] [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Logical Drive to be processed. : Logical Drive Number Specify that Initialize is started or stopped. start: Starts Initialize. stop: Stops Initialize.
mkldc [Overview] Creates a Logical Drive with advanced parameter settings. [Format] Making a Logical Drive having RAID Level of RAID 0, RAID 1, RAID 5 or RAID 6: raidcmd mkldc -c= {-p=, [,, ...
Command Parameter [-y] Description Creates the Logical Drive immediately without displaying the message of confirming that the Logical Drive may be created. [Description] Creates a Logical Drive with advanced parameter settings. The raidcmd create a Logical Drive and terminates after Initialize is started. You can check the progress and result of the Initialize by using "oplist" and "property" commands.
mklds [Overview] Creates a Logical Drive with simple parameter settings. [Format] raidcmd mklds -c= -p=, [,, ... ,] –rl={1 | 5} [-y] Command Parameter -c= -p=, [,, ... ,] -rl={1 | 5} [-y] Description Specify the RAID Controller connecting with Physical Devices used for the Logical Drive.
mkscd [Overview] Creates an SSD Cache Drive. [Format] raidcmd mkscd -c= -p= [,, ... ,] [-y] Command Parameter -c= -p= [,, ... ,] [-y] Description Specify the RAID Controller connecting with Physical Devices used for the SSD Cache Drive. : RAID Controller Number Specify Physical Devices used to create the SSD Cache Drive.
oplist [Overview] Displays the list of operations performed in a RAID Controller and their progresses. [Format] raidcmd oplist [Description] Displays the list of operations performed in a RAID Controller and their progresses. Displayed operations Initialization, Rebuild and Consistency Check Display of terminated operation oplist indicates operations being executed but does not indicate terminated operations.
optctrl [Overview] Allows you to set optional parameters of a RAID Controller. [Format] raidcmd optctrl -c= {-ip={high | middle | low} | -rp={high | middle | low} | -ccp={high | middle | low} | -pr={enable | disable} | -prp={high | middle | low} | -be={enable | disable} | -psd={none | hotspare} | -dst={0.
optld [Overview] Allows you to set optional parameters of a Logical Drive. [Format] raidcmd optld -c= -l= -cm={auto | writeback | writethru} Command Parameter -c= -l= -cm={auto | writeback | writethru} Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Logical Drive to be processed.
property [Overview] Displays the properties of RAID Controllers, Disk Arrays, Logical Drives and/or Physical Devices.
rebuild [Overview] Starts or stops Rebuild. [Format] raidcmd rebuild -c= -p= -op={start|stop} Command Parameter -c= -p= -op={start|stop} Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Physical Device to be processed. : Physical Device Number Specify that Rebuild is started or stopped. start: Starts Rebuild. stop: Stops Rebuild.
refresh [Overview] Refreshes the battery connected to the RAID Controller [Format] raidcmd refresh -c= [-y] Command Parameter -c= [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Refreshing battery immediately without displaying the message of confirming that the Battery Refresh. [Description] Refreshes the battery on the RAID Controller specified.
refreshs [Overview] Refreshes the batteries connected to the RAID Controllers which support the Battery Refresh function. [Format] raidcmd refreshs [Description] Refreshes the batteries connected to the RAID Controllers which support the Battery Refresh function. [Condition] This command can be executed only when the RAID Controller to which the battery is connected supports the Battery Refresh function.
rescan [Overview] Update the RAID System management information of the Universal RAID Utility. [Format] raidcmd rescan [Description] This command collects the configuration information and state information of all of RAID systems managed by the Universal RAID Utility. The management information of RAID System in the Universal RAID Utility is the newest state by this command.
runmode [Overview] Changes the RAID System Management Mode of the raidcmd. [Format] raidcmd runmode [-md={a|s}] Command Parameter [-md={a|s}] Description Specify the altered RAID System Management Mode. If -md option is not specified, shows the current RAID System Management Mode. a: Advanced mode s: Standard mode [Description] Changes the RAID System Management Mode of the raidcmd or indicates the current RAID System Management Mode.
sbuzzer [Overview] Stops the Buzzer on a RAID Controller. [Format] raidcmd sbuzzer -c= Command Parameter -c= Description Specify the RAID Controller to be processed. : RAID Controller Number [Description] Stops the Buzzer sounding in the specified RAID Controller. The command terminates normally if it is executed without Buzzer sounding.
slotlamp [Overview] Turns on or off the DISK lamp of the computer or enclosure in which Physical Devices are installed. [Format] raidcmd slotlamp -c= -p= -sw={on|off} Command Parameter -c= -p= -sw={on|off} Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Physical Device to be processed. : Physical Device Number Specify that the lamp is turned on or off. on: Turns on the lamp.
stspd [Overview] Changes the status of a Physical Device to online or failed forcibly. [Format] raidcmd stspd -c= -p= -st={online|offline} [-y] Command Parameter -c= -p= -st={online|offline} [-y] Description Specify the RAID Controller to be processed. : RAID Controller Number Specify the Physical Device to be processed. : Physical Device Number Specify the altered status.
(no command) [Overview] Displays the version of Universal RAID Utility and the RAID System Configuration as a Tree View. [Format] raidcmd [Description] Displays the version of Universal RAID Utility installed and the RAID System Configuration as a Tree View.
