Desktop Monitor MultiSync EX341R User’s Manual Please find your model name in the label on the backside of monitor.
Index Warning, Caution ..........................................................................................................................English-1 Registration Information ...............................................................................................................English-2 Recommended use ......................................................................................................................English-3 Safety Precautions and Maintenance ................................
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Registration Information FCC Information 1. Use the attached specified cables with this monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. Power supply cord Non shield type, 3-conductor Plug shape U.S.A (2) 2. Please use the supplied shielded video signal cable.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm (15.75 inches) and no further away than 70 cm (27.56 inches) from your eyes.
English Contents For contents, please refer to the contents sheet. Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” (page 3) before installation. The accessories included will depend on the where the LCD monitor is to be shipped. Do not hold Tilt cover. It can damage tilt cover. 1. Turn off the power of your computer. 2.
4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a). If using the cord from a USB device, plug into the downstream port of the monitor. NOTE: Incorrect cable connections may cause abnormal operation, damage display quality/components of LCD module and/ or shorten the module’s life.
NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. Power key Figure E.1 Raise and Lower Monitor Screen The monitor may be raised or lowered in landscape mode. To raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen. Figure RL.
Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount. • To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certified. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2.
This LCD monitor is designed for use with a flexible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand or the specified screws to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand or the specified screws (Figure F.1) to avoid damage to the monitor or stand.
ControlSync ControlSync works controlling all connected sub monitors from master monitor simultaneously but also controlling a target monitor from master monitor by setting INDIVIDUAL ADJUST function (see page 19). Controlling all connected sub monitor (Synchronized control): 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. Follow the steps of DATA COPY.
ECO TOOLS SCREEN COLOR TOOLS MENU TOOLS MULTI DISPLAY ECO INFORMATION BRIGHTNESS* CONTRAST ECO MODE AUTO BRIGHTNESS BLACK LEVEL OFF MODE SETTING OFF MODE SENSOR SETTING OFF MODE START TIME HUMAN SENSING HUMAN SENSOR SETTING HUMAN SENSOR START TIME DV MODE LEFT/RIGHT DOWN/UP H.RESOLUTION V.
Multiple monitors connection using DisplayPort You can connect multiple monitors by using DisplayPort daisy-chain connection. For using as multiple monitors in MST (multi-stream transport) mode, setting should be DP OUT MULTISTREAM “AUTO” at each connected monitor. Please change the monitor setting which is connected to a computer last in the connected monitors. If monitors have no image, turn off the monitor who is connected to a computer then turn it on. Some DisplayPort configuration may be required.
OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the INPUT/SELECT key. NOTE: Exit OSD in order to change signal input. 1 Ambient Light Sensor Human Sensor Detects the level of ambient lighting and the presence of a user, allowing the monitor to make adjustments to various settings resulting in a more comfortable viewing experience. Do not cover this sensor.
ECO TOOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear. CONTRAST Adjusts the overall image and background screen brightness by input signal level. NOTE: When L/B is selected in COLOR control, CONTRAST is disabled. ECO MODE Decreases the amount of power consumption by reducing the brightness level. OFF: No function. 1: Sets brightness variable range from 0% to 70%.
The sensor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has three settings: OFF: No human sensing. 1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode automatically to reduce the power consumption. When a person comes near the monitor again, the monitor will automatically return to normal mode. START TIME adjusts the wait time to react.
OVER SCAN (HDMI input only) Some video formats may require different scanning modes in order to best display the image. 1: Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will be shown on the screen. 2: Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 75% of the image will be shown on the screen. OFF: Image size stays within the display area. The whole image is displayed on the screen.
Selects the method of video detection when more than one video inputs are connected. FIRST: When current video input signal is not present, then the monitor searches for a video signal from the other video input ports. If the video signal is present in another port, then the monitor switches the video source input port to the new found video source automatically. The monitor will not look for other video signals while the current video source is present.
LED BRIGHTNESS You can adjust the blue LED brightness. DDC/CI This function allows the DDC/CI function ON or OFF. USB POWER Selects a power relation of USB. AUTO: Power is supplied to USB downstream port depending on related power condition. ON: Power is always supplied to USB downstream port even when in power save mode or power OFF. NOTE: Power consumption depends on connected USB even when a monitor’s power is off.
If you select “ON”, the Key Guide appears on screen when the OSD menu is accessed. DATA COPY To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch the “INPUT/SELECT” key. A “PROCEEDING...” indicator will appear on the screen. NOTE: This function is only intended for the master monitor in ControlSync. All of the settings specified in the ControlSync chart (see page 11) will be copied from the master monitor to the sub monitor(s).
ECO Information CARBON SAVINGS: Displays the estimated carbon savings information in kg. CARBON USAGE: Displays the estimated carbon usages information in kg. This is the arithmetic estimation, not actual measurement value. COST SAVINGS: Displays the electricity cost savings in balance. CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting is based on the OECD (2008 Edition). CURRENCY SETTING: Displays electricity pricing in 6 currency units.
Monitor Specifications MultiSync EX341R Notes LCD Module 86.43 cm/34.0 inches 86.43 cm/34.0 inches 3440 x 1440 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.2318 mm dot pitch; 290 cd/m2 white luminance; 3000:1 contrast ratio (typical), (20000:1 Contrast ratio, Dynamic). DisplayPort Connector: Digital RGB DisplayPort Complies with Standard V1.2, applicable to HDCP HDMI Connector: Digital YUV Digital RGB HDMI 1 (HDCP2.2), HDMI 2 (HDCP1.
Features Ultra Wide 1800R Curve: Ultra Wide 21:9 aspect 3440 x 1440 resolution provides large and flexible working space without bezels, which can replace 3 units of 19" SXGA or 2 units of 23" FHD/24" WUXGA. In addition, 1800 mm radius curve provides ergonomic benefits like less neck movement and less color shift by less angled and nearer of edge image with less color shift. DisplayPort OUT: This monitor has a DisplayPort out connector for daisy-chain connection.
No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter adapter. • When you use DisplayPort signal, check to make sure not to plug the input signal cable in DisplayPort out connector. • Power Switch and computer power switch should be in the ON position.
Display image is not sized properly • Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • When using an HDMI input, please change “OVER SCAN”. • Check to make sure that the appropriate resolution has been selected in H.RESOLUTION and V.RESOLUTION.
English Using the Zoom Function Allows you to use the entire screen area, significantly expanding the size. Allows the picture displayed in the center to expand. SETUP 1. Select FULL or ASPECT in EXPANSION to activate the Zoom function (see page 16). EXPANSION OFF 2. Set a resolution via H.RESOLUTION or V.RESOLUTION (see page 15). Vertical expansion Horizontal expansion 3.
Human sensing function Human sensing function reduces power consumption by detecting the movement of a person. The HUMAN SENSING has following two settings: MODE HUMAN SENSING SETTING No person in front of the monitor LIGHT 1 BRIGHTNESS 0% DEEP 2 Power saving mode Image of human sensing operation A. When sensor detects no person in front of the monitor, the monitor stays for a period of time which is set at HUMAN SENSING > START TIME (see page 15). B.
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
