MultiSync EA193Mi User’s Manual
Index Warning, Caution ..........................................................................................................................English-1 Registration Information ...............................................................................................................English-2 Recommended use ......................................................................................................................English-3 Contents ..........................................................
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Registration Information Canadian Department of Communications Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm (15.75 inches) and no further away than 70 cm (27.56 inches) from your eyes.
English Contents Your new NEC monitor box* should contain the following: • MultiSync monitor • Power Cord*1 • Base • Video Signal Cable (DVI-D to DVI-D cable) • Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) • Audio Cable (ø 3.5 stereo mini plug) • Setup Manual Mini D-SUB 15 pin to Mini D-SUB 15 pin Power Cord*1 Audio Cable Setup M anual Setup Manual * DVI-D to DVI-D cable Base Remember to save your original box and packing material to transport or ship the monitor.
Quick Start To attach the Base to the LCD stand: 1. Place the monitor face down on a non-abrasive surface (Figure 1). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 2. Please rotate the stand 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand. 3. Attach the base to the stand and properly lock screw of base’s bottom (Figure 2). NOTE: Figure 1 Control buttons Reverse this procedure if you need to re-pack the monitor.
English 5. Position the Video Signal Cable and power cord between the holes on the Stand, as indicated in Figure B.2/Figure B.3. Figure B.2 Figure B.3 6. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NOTE: Please refer to Caution section of this manual for proper selection of AC power cord. 7. Turn on the computer, then turn on the monitor by pressing the power button on the front bezel (Figure C.1). 8.
Screen Rotation Before rotating, disconnect power cord and all cables, then the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your fingers. To raise the screen, place a hand on each side of the monitor and lift up to the highest position (Figure RL.1). To rotate screen, place a hand on each side of the monitor screen and turn clockwise from landscape to portrait or counterclockwise from portrait to landscape (Figure R.1).
This LCD monitor is designed for use with a flexible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount. • To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certified. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2.
Mount Flexible Arm This LCD monitor is designed for use with a flexible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
OSD (On-Screen Display) control buttons on the front of the monitor function are as follows: To access OSD menu, press any of the control buttons (MENU, Left, Right, Down, Up). To change signal input, press the SELECT button. To change ECO MODE, press the RESET/ECO MODE button. NOTE: Exit OSD in order to change signal input.
AUTO BRIGHTNESS OFF: No function. 1 (AMBIENT LIGHT): Automatically adjusts the brightness to the optimal setting by detecting the brightness level of the environment*1. *1: Please refer to page 20 for full “Auto Brightness” information. 2 (WHITE CONTENT): Automatically adjusts the brightness to the optimal brightness setting based on the white display area. The environmental brightness sensor (Ambibright sensor) has no function.
Adjusts the horizontal size by increasing or decreasing this setting. If the “AUTO ADJUST” function does not give you a satisfactory picture setting, a further tuning can be performed by using the “H.SIZE” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width of the picture. Use LEFT/RIGHT key to center the image on the screen. If the H.SIZE is wrongly calibrated, the result would look like the left drawing. The image should be homogeneous. When H.
RESPONSE IMPROVE Turns the Response Improve function ON or OFF. Response Improve may reduce blurring that occurs in some moving images. OFF TIMER Monitor will automatically power down when you have selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes. Touch any OSD key to delay the power-down time.
CARBON SAVINGS: Displays the estimated carbon savings information in kg. CARBON USAGE: Displays the estimated carbon usages information in kg. This is the arithmetic estimation, not actual measurement value. COST SAVINGS: Displays the electricity cost savings in balance. CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting is based on the OECD (2008 Edition). CURRENCY SETTING: Displays electricity pricing in 6 currency units.
Specifications Monitor Specifications MultiSync EA193Mi Notes LCD Module 47.99 cm/19 inches 47.99 cm/19 inches 1280 x 1024 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.293 mm dot pitch; 250 cd/m2 white luminance; 1000:1 contrast ratio (typical), (25000:1 Contrast ratio, Dynamic). DisplayPort Connector: Digital RGB DisplayPort Complies with Standard V1.2, applicable to HDCP DVI-D 24pin: Digital RGB DVI (HDCP) Analog RGB Sync 0.7 Vp-p/75 ohm Separate sync.
DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity. It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables. OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus.
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Front Power Switch and computer power switch should be in the ON position. • The monitor will automatically turn off by “POWER SAVE TIMER” function when continuing power save mode for 2 hours. Please touch the power button.
English No Sound • Make sure the speaker cable is proper connected. • Check to see if mute is activated. • Check the VOLUME in the OSD menu. • Check selected OSD’s Tools to “SOUND INPUT”, when DisplayPort is in use. Brightness variations over time • Change AUTO BRIGHTNESS to OFF and adjust brightness. NOTE: When AUTO BRIGHTNESS is set to ON, the monitor automatically adjusts brightness based on the environment. When the brightness of surrounding environment changes, the monitor will also change.
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions. The Auto Brightness function is set to 1 by default.
Congratulations! This product is TCO Certified – for Sustainable IT TCO CertiÞed is an international third party sustainability certiÞcation for IT products. TCO CertiÞed ensures that the manufacture, use and recycling of IT products reßect environmental, social and economic responsibility. Every TCO CertiÞed product model is veriÞed by an accredited independent test laboratory.
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
