*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page I NEAX 2400IPX ® Internet Protocol eXchange DTERM ® SERIES i DTERM ® IP USER GUIDE
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page II LIABILITY DISCLAIMER NEC AMERICA, INC. RESERVES THE RIGHT TO CHANGE THE SPECIFICATIONS, FUNCTIONS, OR FEATURES, AT ANY TIME, WITHOUT NOTICE. NEC AMERICA, INC. HAS PREPARED THIS DOCUMENT FOR USE BY ITS EMPLOYEES AND CUSTOMERS. THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF NEC AMERICA, INC. AND SHALL NOT BE REPRODUCED WITHOUT PRIOR WRITTEN APPROVAL FROM NEC AMERICA, INC. COPYRIGHT 2003 NEC AMERICA, INC.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 1 TABLE OF CONTENTS KEYS AND LAMPS SOFT KEYS TERMINAL SETUP WITH THE UP/DOWN KEY TERMINAL SETUP WITH THE FEATURE KEY LOGIN/LOGOUT (IP ENABLED DTERM/DTERM IP ONLY) TO ORIGINATE AN OUTSIDE CALL TO ORIGINATE AN INTERNAL CALL MULTILINE APPEARANCE TO ORIGINATE A CALL USING SPEED CALLING ( ONE-TOUCH BUTTONS) TO ORIGINATE A CALL USING SPEED CALLING ( INDIVIDUAL /GROUP ) TO ORIGINATE A CALL USING SPEED CALLING – SYSTEM ACCOUNT CODE FORCED ACCOUNT CODE AUTHORIZATION C
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 2 KEYS AND LAMPS PROGRAMMABLE KEYS FWD-A Press key to activate, verify or cancel “Call Forwarding – Don’t Answer” feature. These are examples of Dterm® features available by pressing the programmable keys. Some features may be programmed by the user. Keys must be programmed by the telephone system administrator. MICM Press key to activate “Manual Intercom.” AICM Press key to activate “Automatic Intercom.” DICM Press key to activate “Dial Intercom.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 3 LCD Liquid Crystal Diode (LCD) display provides Dterm activity information plus date, time and Soft Key operation. LED Some Feature keys have a built-in Light Emitting Diode (LED) that lights or flashes according to the activity of that Feature key. LAMPS Call Indicator Lamp Lamp at top of Dterm Display flashes when a call terminates to the terminal. Lamp lights steadily when a message has been left.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 4 SOFT KEYS FUNCTION KEY ACTIVITIES Feature + 1 = Turns microphone on or off. Feature + 2 = Adjusts handset receiver volume. The Soft Keys on the Dterm® Series i/Dterm IP provide a set of functions on the LCD that adapts to the changing state of the telephone. While default Soft Key settings are provided, desired functions can be assigned to individual stations as required.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 5 DEFAULT FUNCTION DISPLAYS FOR EACH STATUS 4051 7:35 AM MON 18 JUL 2002 >>> MIC DND Exit Default Soft Key settings are provided corresponding to particular functions. Different Soft Key settings are displayed at the bottom of the LCD depending on the state of the call, as shown below. Help Exit Key Press the Exit key to exit the Help program.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 6 SOFT KEY FEATURES RINGING When the Soft Key corresponding to a desired function name is operated, the selected function name starts to blink on the LCD. The blinking display of available functions takes precedence over the display of functions specified by the Soft Key pattern.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 7 HOLD (Call Hold) Permits a station user to hold a call in progress and to return to the previously held call. CW (Call Waiting) Enables a busy station to receive a second incoming call. A camp-on indication tone is sent to the busy station, and the user can use a switchhook flash to answer the second call. PICK (Call Pickup – Group) Permits a station user to answer any call directed to other lines in the user’s preset Call Pickup Group.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 8 S-SPD (Speed Calling – System) Allows a station user to call certain frequently dialed numbers using fewer digits (abbreviated call codes) than would normally be required. CAS (CAS – Switch Hook Flash) Allows the user to send a switchhook flash while on an outside trunk. FLASH (Flash) Provides the station with a switchhook flash.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 9 HSET (Headset) Allows the user to go off- and on-hook when using the headset. RLS (Release Key) Allows the user to release the current call when using the headset, without waiting for the party to hang up. GPICK (Call Pickup – Group Enhancement) Allows the user to answer any ringing station within the user’s expanded call pickup group.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 10 TERMINAL SETUP WITH THE UP/DOWN KEY CHCNF (Call Hold – Conference) Allows a station user to establish a conference connection by adding a third party, who is held on another line, to the existing two-party connection. Note: Not Displayed for Dterm 65/Dterm Series III and Dterm 75/Dterm Series E mode.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 11 TERMINAL SETUP WITH THE FEATURE KEY TO ADJUST THE SPEAKER VOLUME the ▲ or▼ key during SPEAKER speakerphone operation or engaged in a call. ◆ Press --- MICROPHONE ON/OFF TO ADJUST RINGER TONE the ▲ or▼ key during ringing. LED on Mic key shows the status of the built-in microphone. ◆ Press RING To change microphone status: ---------- TO ADJUST LCD ◆ Press Soft Key associated with the MIC Display or press Feature and 1.
*NEC-405 NEAX2400 UG #2 1/22/03 ◆ Press Feature and 2 to alternate between Large and Small volume. 2:42 PM Page 12 RCV VOL. TONE NO. LARGE (Time Display) TO SELECT RINGER TONE FREQUENCY (HZ) MODULATION (HZ) 1 520/660HZ 16HZ 2 520/660HZ 8HZ 3 1100/1400HZ 16HZ 4 660/760HZ 16HZ The Dterm Series i/Dterm IP has nine kinds of ringer tones that you can select. 5 MELODY 1 6 MELODY 2 ◆ Press Feature and 3.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 13 TO ADJUST TRANSMISSION/ CALL INDICATOR LAMP ON/OFF RECEIVING VOLUME The user can choose to turn the call indicator lamp either on or off during ringing. Handset volume can be changed. ◆ Press Feature and 4. T/R VOL. The LCD displays the current volume. ◆ Press Feature and 4 ◆ Press Feature and 7. The LCD displays: SMALL (Time Display) T/R VOL. again to alternate between Small and Large volume.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 16 TO ORIGINATE AN INTERNAL CALL TO ORIGINATE AN OUTSIDE CALL ◆ Lift handset or press Speaker key, receive dial tone. ◆ Lift ◆ Dial the Central Office access code, e.g. 9. ◆ Dial desired telephone number. ◆ Use handset or MIC to converse. ◆ Display indicates: Elapsed time 15:39 handset or press Speaker key. ◆ Receive dial tone. ◆ Dial desired station number. Display indicates digits dialed.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 17 MULTILINE APPEARANCE TO ORIGINATE A CALL USING SPEED CALLING (ONE-TOUCH BUTTONS) TO ORIGINATE ◆ Press the MULTILINE APPEARANCE feature key. the desired Speed Call button, or press Speaker and Speed Call. ◆ Press handset or press Speaker, receive Central Office or distant PBX dial tone. ◆ Lift ◆ Dial TO PROGRAM the destination. Note: Available only on Dterm stations with speed calling keys.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 18 TO VERIFY (WITH DTERM 8D/16D/32D) TO ORIGINATE A CALL USING SPEED CALLING (INDIVIDUAL/GROUP) ◆ Press Feature button. ◆ Press desired Speed Dial button. ◆ Display indicates digits programmed. Note 1: To program a hook switch for transfer or feature activation, press Recall key as first digit. (! displays on LCD.) ◆ Press ◆ Press the Redial button. the desired speed calling number.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 19 TO ORIGINATE A CALL USING SPEED CALLING – SYSTEM TO OPERATE FROM THE SPEED CALLING – SYSTEM KEY the “Speed Calling – System” ◆ Press XXXX (Time Display) key. ◆ If the Dterm does not have the “Speed Calling – System” key, dial the “Speed Calling – System” access code, then the abbreviated call code. TO PROGRAM SPEED CALLING – SYSTEM KEY (ON ONE-TOUCH SPEED CALLING KEY) ◆ Press Feature key.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 22 VOICE CALL ◆ Lift Note 1: A Voice Call may be programmed on a one-touch speed key by pressing Speed Dial button, dialing the extension and pressing the Transfer key. (V displays if programming on an LCD Display Dterm. Save by pressing Speed Dial again.) handset. ◆ Dial Note 2: If called party is on their line when a Voice Call is attempted, calling station’s display indicates: VOICE BUSY desired station number. ◆ Press Voice.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 23 TO ANSWER A VOICE CALL HANDS-FREE AUTOMATIC INTERCOM TO INITIATE ◆ Receive incoming Voice Call. ◆ Lift Called party the MIC Soft Key or Mic. LED lights. ◆ Press ◆ Respond hands-free. handset or press Speaker key. ◆ Press VOICE the AICM key. ICM 2 (Time Display) Calling station ◆ Hear 2001 tone. (Time Display) NOTE: If privacy is required, lift handset. ringback TO ANSWER ◆ AICM key flashes red indicating an incoming intercom call.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 24 MANUAL INTERCOM original caller on hold (with HOLD key). TO INITIATE ◆ Press MICM, lift handset or press Speaker, ringback tone is heard. Called party ICM 2 (Time Display) the SIG key if it is desired for the called station to hear ringing. ◆ Press TO ANSWER ◆ MICM key flashes, indicating an incoming call. Ring tone may also be heard. ◆ Press MICM.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 25 DIAL INTERCOM handset or press Speaker, LED lights solid green. ◆ Lift ◆ If called station is engaged in a non-intercom call, the station may press MICM after placing original caller on hold (with Hold key). TO INITIATE ◆ Lift handset or press the Speaker key. Called party ◆ Press DICM key. ICM 2 (Time Display) ◆ Dial desired intercom station number. Receive ringback tone. TO ANSWER ◆ DICM LED flashes, indicating an incoming intercom call.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 26 TO PLACE A CALL ON HOLD ◆ If called station is engaged in a non-intercom call, the station may press DICM after placing the original call on hold (with the Hold key.) ◆ Press Hold. Held line wink flashes. Held station number HOLD 2001 (Time Display) Note: If held line appears on other Dterm stations, the associated LED flashes red slowly. TO RETRIEVE ◆ Lift handset or press Speaker. ◆ Press held line. Use handset to converse.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 27 TO PLACE A CALL ON EXCLUSIVE HOLD IF UNANSWERED ◆ After preprogrammed time, Automatic Recall is initiated. Held station number ◆ Visual and audible signal (rapid flash and ring burst) is sent to station that placed call on hold. ◆ Press Hold twice. Line appearance indicates interrupted wink. Note 1: A transfer or conference call may be placed on hold depending on software level of the NEAX2400 IPX.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 28 TO TRANSFER A CALL IF UNANSWERED ◆ After preprogrammed time, Automatic Recall is initiated. ◆ After ◆ Visual and audible signal (rapid flash and ring burst) is sent to station which placed call on Exclusive Hold. Recall shows as a flashing green LED on your phone, and solid red on other phones with same line. conversing, ask party to hold. ◆ Press Transfer. Receive interrupted dial tone.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 29 CONFERENCE USING THE SOFT KEY a call in progress, press Transfer and dial desired number. ◆ With ◆ With call in progress, ask party to hold. ◆ Press Transfer, ◆ Dial ◆ After call is answered, press CONF Soft Key. receive interrupted dial tone. CONF (Time Display) MIC desired number. ◆ Three-way ◆ After call is answered, press Conf. Conf LED lights. ◆ Three-way conference is established.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 30 TO ESTABLISH A BROKER CALL ◆ While engaged in a call and wishing to consult a third party, press Transfer. Caller is automatically placed on hold. ◆ Dial desired party to consult. ◆ Press Transfer to return to original caller. Third party is automatically placed on hold. ◆ By repeating these steps, it is possible to alternate between calls. Note: The display indicates connected station or trunk at any given time.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 34 CALL PICK-UP (GROUP) USING THE SOFT KEY ◆ Lift to calling party is established. Called station ◆ Connection WHEN A STATION WITHIN PICK-UP GROUP RINGS ◆ Lift handset and press PICK Soft Key. handset. PICK UP 2000 Calling party 2001 (Time Display) MIC >>> ◆ Press CALL PICK-UP or dial “Call Pick-up” access code (may be stored on one-touch speed calling key). ◆ Connection ◆ If CALL PICK-UP (DIRECT) to calling party is established.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 35 WHEN A STATION WITHIN THE SYSTEM RINGS ◆ Lift handset, receive dial tone. ◆ Press PICK-DIRECT and dial the station number to be picked up. – OR – ◆ Dial “Direct Call Pick-up” access code and the station number to be picked up. to calling party is established. Called station ◆ Connection PICK UP Calling party 2000 DDD 3 (Time Display) ◆ If busy, original call must be placed on hold before new call can be picked up.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 36 OFF-HOOK TRUNK QUEUING ◆ Press Speaker, ◆ Dial receive dial tone. “Off-hook Queuing” access code. ◆ Dial desired telephone number. Encounter a trunk busy condition. ◆ Station user receives service set tone and leaves speaker on. ◆ The desired number is automatically dialed when a trunk becomes available.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 37 LAST NUMBER REDIAL TO RECALL THE LAST NUMBER DIALED ◆ Press Redial. Last number dialed is displayed. ◆ Press Redial key until desired number is displayed. Up to 5 previously dialed numbers. ◆ Pres ✽ (Note) LNR[# or *]/SPD[_ _] The number on the display is automatically redialed. ◆ When -X XXXXXX party has answered, lift handset or speak hands-free.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 38 CALL FORWARDING – ALL CALLS USING THE SOFT KEY ◆ Press FDA Soft ◆ Dial ◆ If destination; wait for service set tone. ◆ “FORWARD SET” is displayed, Call Forwarding for all calls is set. TO SET ◆ Press Speaker. Key. Receive special tone. Receive dial tone. FORWARD SET (Time Display) >>> MIC setting for another station, press TO VERIFY (WITH DTERM 8D/16D/32D) MULTILINE APPEARANCE. ◆ Press FWD or dial “Call Forwarding – All Calls” access code.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 39 CALL FORWARDING – BUSY LINE TO CANCEL ◆ Press Speaker. Receive dial tone. If cancelling for another station, press MULTILINE APPEARANCE. ◆ Press FWD or dial FORWARD CANCEL (Time Display) “Call Forwarding – All Calls” cancel code. Receive service set tone. LED goes out at your station (or the Dterm of the multiline station). ◆ Press Speaker. TO SET ◆ Press Speaker. ◆ If ◆ Press FWD-BY or dial “Call Forwarding – Busy Line” access code.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 40 USING THE SOFT KEY TO CANCEL ◆ Press FDB Soft ◆ Press Speaker. ◆ Dial Key. Receive special dial tone. Receive dial tone. If canceling for another station, press MULTILINE APPEARANCE. destination; wait for service set tone. ◆ “FORWARD SET” is displayed; Call Forwarding – Busy Line is set. FORWARD SET ◆ Press FWD-BY or (Time Display) MIC TO VERIFY (WITH DTERM 8D/16D/32D) ◆ Press FWD-BY. ◆ Press Speaker.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 41 CALL FORWARDING – DON’T ANSWER ◆ Press Speaker. Call Forwarding – SET Don’t Answer is set. FORWARD(Time Display) TO SET ◆ Press Speaker. Forwarding station 2000 USING THE SOFT KEY Receive dial tone. ◆ Press FDN Soft setting for another station, press MULTILINE APPEARANCE. ◆ If ◆ Dial Key. Receive special dial tone. destination; wait for service set tone.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 42 ◆ Display indicates the station number calls are forwarded to. Note 1: If recipient station is a Dterm 8D/16D/32D, LCD displays: TO CANCEL Forwarding station FORWARD ◆ Press Speaker. Receive dial tone. If cancelling for another station, press MULTILINE APPEARANCE. 2000 (Time Display) ◆ Press FWD-NA or FORWARD CANCEL (Time Display) dial “Call Forwarding – Don’t Answer” cancel code. Receive service set tone.
*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page 44 USING THE SOFT KEY TO CANCEL handset or press Speaker key; receive Dial Tone. ◆ Lift ◆ Lift ◆ Dial ◆ Press FDL Soft handset or press Speaker key; receive Dial Tone. “Logged Out IP Station – Call Destination” cancel code; receive service set tone. Key; receive service set tone. ◆ Dial destination station number; receive service set tone. handset or FORWARD CANCEL (Time Display) press Speaker key.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 56 DO NOT DISTURB Option 4 presses Answer and converses with Secretary. Trunk A is placed on hold. ◆ Boss denies call, presses Transfer to return to Trunk A. ◆ Boss ◆ Secretary WHILE IDLE (ON-HOOK) ◆ Press DND. is returned to Trunk B. LED DND SET lights. Note: If boss has 8/16/32 button display terminal, display always indicates the connected station or trunk at any given time. (Time Display) Note: With Soft Key operation, “DND” flashes when set.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 59 Note 1: Station A can be a single-line station if it appears on the Station B Dterm. Note 2: Up to six parties can break into a two-party conversation (additional hardware required).
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 60 INDEX C Call Back Call Forwarding – All Calls Call Forwarding – Busy Line Call Forwarding – Don’t Answer Call Park Call Pick-up (Direct) Call Pick-up (Group) Call Transfer Call Waiting – Originating Camped-on Call, Answering Conference A Account Code Answering a Camped-on Call Answering a Message Answering a Voice Call Hands-free Authorization Code Automatic Intercom 20 30 48 23 21 23 B Boss/Secretary – MW Lamp Control Boss/Secretary Override Boss/Secr
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 61 Message, Answering Message, Leaving Microphone Key Multiline Appearance F Forced Account Code Function Keys and Lamps 20 2 H Headset Key Help Hold N 9 5 26 Number Save and Repeat Off-hook Trunk Queuing Originating a Call Using Speed Calling (Individual/Group) Originating a Call Using Speed Calling (One-touch Buttons) Originating a Call Using Speed Calling – System Originating an Internal Call Originating an Outside Call Outgoing Trunk Queuing Outside
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 62 P Paging Transfer Placing a Call on Exclusive Hold Placing a Call on Hold Privacy Privacy Release V 50 27 26 57 58 Voice Call Voice Call Hands-free, Answering Voice Mail System S Saving and Repeating a Number Speed Calling – System Speed Calling Call Origination (Individual/Group) Speed Calling Call Origination (One-touch Buttons) 46 19 18 17 T Terminal Setup with the Feature Key Terminal Setup with the Up/Down Key Transfer a Call 11 10 28 62 22 23
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 63 LCD DISPLAYS CALLBACK SET XXXX Call Back set for busy called station. 15:39 DDD CALLPARK SET X Incoming call is parked. Time elapsed, trunk type and number for outside call. Time elapsed for parked call. XXX DDD X CAMP ON DDD X X Camped on call placed on hold. Parked call retrieved from a remote station, showing the number of the station that parked the call. CONF Three-party conference established.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM C WAIT Page 64 XXXX E E-HOLD OR C WAIT SET XXXX Station placed on Exclusive Hold. XXXX Call Waiting tone sent to or received at busy station show in called or calling number. F FORWARD Call received on boss’ station from secretary’s station. XXXX Station displays forwarding destination. Call Forwarding – All Calls. D Call Forwarding – Busy Line. DND SET/CANCEL Call Forwarding – Don’t Answer. Do Not Disturb set or canceled.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 65 Call Forwarding – All Calls. Automatic Intercom. Call Forwarding – Busy Line. Manual Intercom. Call Forwarding – Don’t Answer. Dial Intercom. Logged Out IP Station – Call Destination. Boss Secretary Transfer. H INDICATOR O/OFF HANDS-FREE Indicator Lamp status. ON/OFF L Hands-free status. HOLD XXXX LNR[*]/SPD[_]-N Station placed on hold. Prompt for last number called or Speed Calling number. I ICM Stack Dial.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 66 LOGIN MESSAGE CANCEL The IP Enabled Dterm becomes operational when the user enters “Login Code” and “Password.” Message erased. LOGOUT Called Station message receipt restricted – not equipped to receive messages. MESSAGE REST Press preassigned Logout button to logout. MESSAGE SET M XXXX Message indication left and busy called station. MSG XXXX HH:MMPM MW SET/CANCEL Message waiting (calling station and time of message).
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM OVERRIDE Page 67 X PAGING X Overriding intercom call through bridging. OR Automatic Intercom. PAGING Dial Intercom. Ready to page station, page waiting or page call connection. Manual Intercom. OVERRIDE X P-RLS SET XXXX Privacy Release set. Executive Override. P-RLS ? P PICK UP DDD XXXX Prompt requesting privacy release for incoming call. X Call Pickup of station within group showing called and calling stations.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 68 R TRANSFER RCV VOL. SMALL/LARGE Transferred station or trunk number. Receiver Volume status. Page Call Transfer. RINGER TONE TRANSFER XXXX X XXXX X Transferring station number. Ready for Ringer tone selection. TRANSFER S 3 Transferring page call to another station. SPEED SET T/R VOL. SMALL/LARGE Speed Calling number saved in memory. Transmission Receiving Volume status. T V TRANSFER VOICE Ready to transfer a call.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 69 VOICE BUSY/REST Voice Call station called is busy or restricted. W WAIT P-RLS? Prompt when requesting privacy release at another station.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 70 FACE LAYOUT 1 CALL INDICATOR LAMP • Trunk line access • Feature access (Note 2) • Any feature can be assigned. • Direct station selection • Station speed dial Lamp at top corner of Dterm Display flashes when a call terminates to the terminal. Lamp lights steadily when a message has been left. 2 LCD(NOTE1) Liquid Crystal Diode (LCD) display provides Dterm activity information plus date, time and Soft Key Operation.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 71 14 MICROPHONE Built-in microphone is used for hands free operation with speakerphone. 15 UP/DOWN ( ▼ DOWN ▲ UP) Used to adjust LCD contrast, speaker/receiver volume, and ringer volume. • LCD Contrast: Press (▼) or (▲) key while idle. • Speaker/Receiver Volume: Press (▼) or (▲) key during conversation. • Ringer Volume: Press (▼) or (▲) key during ringing. 16 ANSWER When LED on this key is lighted, press key to answer a waiting call.
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 72 DTERM 32D (32-LINE WITH DISPLAY) 1 2 3 Help Exit 4 5 6 7 8 1 2 ABC 3 DEF Recall 9 Feature Directory 4 GHI 5 JKL 6 Conf 10 Mic MNO Message 7 PQRS 8 TUV 0 OPER 9 Redial WXYZ # Answer Hold Transfer Speaker 19 18 17 11 12 13 14 15 16 20
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 73 DTERM8 (8-LINE NON DISPLAY) DTERM8D (8-LINE WITH DISPLAY) 1 Call Indicator Lamp Help Exit 6 1 2 3 DEF Recall Feature ABC 5 JKL 6 Conf Mic 9 Redial Programmable Keys 1 2 3 DEF Recall Feature ABC 5 JKL 6 Conf Mic GHI 4 GHI MNO 8 TUV 9 Redial 0 Hold # 7 PQRS 8 TUV 0 Answer OPER Speaker LCD Display 4 Soft Keys 6 Programmable Keys Message Dedicated Function Dedicated Keys Keys WXYZ Transfer 2 MNO Message
*NEC-405 NEAX2400 UG #2 1/22/03 2:43 PM Page 74 For more information contact: ©NEC America, Inc. 2003 NEAX and Dterm are registered trademarks of NEC Corporation. FPO BAR CODE 188301 NEC America, Inc. Corporate Networks Group 6555 N. State Highway 161 Irving Texas 75039 Visit our Web site at www.cng.nec.