WALL Family Wall mounted I/O unit User manual NE41 12005-02 v2.
Information in this User manual is subject to change without notice. US Notes NEAT Electronics AB reserves the right to change or improve their products and to make changes to the content without obligation to notify any person or organization of such changes or improvements. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Contents About WALL Family products About WALL Family products 3 Product variants 4 Hardware overview 4 Front overview 4 Back overview 4 The screw connector 5 Power 5 Inputs IN1 and IN2 5 Outputs OUT1 and OUT2 5 Jumpers J1 and J2 6 Buttons and LEDs 6 Ports 1 and 2 6 Manual configuration 7 Remove a transmitter 9 WALL family Programmer 9 More information 9 Important! 9 Care and maintenance 9 Safety Notes 9 Disposal 10 Technical data 11 The WALL Family consist of 11 products divided into
Product variants Product Button WIOR Category products WIOR KEY PULL PEAR PUSH x1 PUSH+PEAR x1 PUSH+PULL x1 3PUSH x3 3PUSH+PEAR x 3 The unit is designed to fit in an inset coupling box with cc 60 mm. To mount directly on a wall, an optional mounting frame must be fitted. Connector Key cylinder Pull cord 6.35 mm tele jack 6.35 mm tele jack Pull cord PUSH+PEAR Back overview 6.35 mm tele jack On the back are the connectors and contacts. ROOM Category products ROOM ROOM+PEAR x3 x3 6.
Item ① ② ③ ④ ⑤ ⑥ Power Denomination Place for 6.35 mm tele jack connector/Pull cord/Key cylinder Jumper J2 Jumper J1 AAA-battery connectors Screw connector Product (data) label The screw connector The screw connector allows for connecting external power, inputs and outputs by cable to the WALL unit. 10-28 VDC The unit can be powered either by 10-28VDC or 2 x AAA batteries. Inputs IN1 and IN2 In the screw connector there are two wired inputs, IN1 (pin 6) and IN2 (pin 5).
The builtin actionplan activates the outputs as below. Mode OUT1 OUT2 Standby Alarm Presence Assistance Active Active Active Active All other products The relay outputs acts according to settings made by manual configuration or by a superior system (by radio). Jumpers J1 and J2 As default the jumpers J1 and J2 has the functions as described below.
Both ports have a common ground and must be connected to potential free contacts (see below). Port 1 Manual configuration (not valid for ROOM and ROOM+PEAR) Any unit can be manually configured regarding adding transmitters and how the two relay outputs should act when the added transitter is activated. The procedure is in short: Port 2 Port 1 If an inserted tele plug is removed, the unit sends a Tamper alarm. If the plug is inserted again the unit sends a Tamper OK alarm.
5. After the initial “three green blink”, the unit now starts to blink red. The number of blinks indicates the current radio position, i.e. 3 red blinks equals radio position 3. 1 2 3 4 5 6 7 8 1 2 6. To select radio position, press any button, port or input. 7. The unit will confirm the selection by lighting green for 2 second. 8. Now activate the radio transmitter (e.g. press the red button on an ATOM). 9.
In the event of inactivity during manual configuration (e.g. a transmitter is not activated after #8 or a port/ button is not pressed after #11) the unit waits for 60 seconds and then returns to normal mode. The manual configuraton must then be restarted. Remove a transmitter To remove a transmitter, follow steps #1 trough #7 above. After step #7, remove jumper J2. The device will confirm the deletion by rapidly blink green for 2 seconds.
• This product should not be a substitute for the routine visual monitoring protocol by caregiver. • Must not be used in situations where a delay in the arrival of appropriate medical care, could lead to a potentially lifethreatening situation. • Check device regularly and replace when necessary. • Do not integrate to other systems other than those specified in this document. • Always keep the device dry. Exposure to excessive moist can cause malfunction.
Technical data Data Value Dimension (incl. wallframe)(mm) Weight (incl. batteries) Frequencytransmit 86 x 86 x 26 mm 125 g EU US 868.7, 869.2 MHz 916.2, 916.4 MHz EU US 868.7, 869.2, 869.4 MHz 916.2, 916.
www.neatelectronics.