Manualshelf

Product Manual

ManualsBrandsNCE ManualsCaravan Appliances12VDC Stainless Steel Rangehood
12345678
3
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
,
noting required height and clearance regulations
Th
e NC
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
)
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
the 12volt power
connect
ion completed correctly
)
and locate pre-marked holes
5.
hown above)
6.
Install
7.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
source
(Wires
are
labelled
+/-
take care to ensure
4.
Lift
Rangehood
into designated position
filter
s
Use
4
x
SS
screws
only
into
locating
holes
(
s
NCE recommends that after mount, power on and test all functions
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
,
noting required height and clearance regulations
Th
e NC
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of the Rangehood
)
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
the 12volt power
connect
ion completed correctly
)
and locate pre-marked holes
5.
hown above)
6.
Install
7.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
source
(Wires
are
labelled
+/-
take care to ensure
4.
Lift
Rangehood
into designated position
filter
s
Use
4
x
SS
screws
only
into locating
holes
(
s
NCE recommends that after mount, power on and test all functions
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
,
noting required height and clearance regulations
Th
e NC
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
)
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
the 12volt power
connect
ion completed correctly
)
4.
and locate pre-marked holes
5. Use
hown above)
6.
Install filter
7.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
source
(Wires
are
labelled
+/-
take care to ensure
Lift
Rangehood
into designated position
4
x
SS
screws
only
into
locating
holes
(
s
s
NCE recommends that after mount, power on and test all functions
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a
Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
Th
e NC
,
noting required height and clearance regulations
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
)
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
power
)
5.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
Use
4
x
SS
screws
only
into
locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a
Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
Th
e NC
,
noting required height and clearance regulations
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
)
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
power
)
5.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
November 201
6
INSTALLATION:
Note:
The NCE530LEDG is designed to operate on 12Volt DC power only. Installation
into a
Recreational
Vehicle
must be compliant with Australian Standard
AS5601-2004
Th
e NC
,
noting required height and clearance regulations
E530LEDG
Rangehood
can
be
installed
via
overhead
or side mounting
.
Option 1.
Overhead
Mounting
Holes required MUST be measured and marked prior to any alteration to cabinet
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
power
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
)
4.
Lift
Rangehood
into designated position
and locate pre-marked holes
5.
Use
4
x
SS
screws
only
into locating
holes
(
s
hown
above)
6.
Install
filter
s
7.
NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
NCE
Rangehood
- NCE530LEDG
power
)
4.
5. Use
6.
Install filter
7.
1.
Remove
filter
s
2.
Locate
holes in
the top of
the Rangehood
3.
Connect
rangehood power wires to pre-installed RV wiring using
the 12volt
source
(Wires
are
labelled
+/-
take care to ensure
connect
ion completed correctly
Lift
Rangehood
into designated position
and locate pre-marked holes
4
x
SS
screws
only
into
locating
holes
(
s
hown
above)
s
NCE recommends that after mount, power on and test all functions
Where the required clearance to a range hood cannot be met, a range hood constructed of non-
combustible materials may be installed at not less than 450 mm, provided that
(i) the range hood is suitable at the installed clearance; and
(ii) the gas appliance is certified as a caravan/marine cooker at the installed clearance.
Note: This requirement does not apply to the installation of commercial catering equipment.
INSTALLATION
Note: The RH530LEDG is designed to operate on 12 Volt DC power only. Installation into a Recreational
Vehicle must be compliant with Australian Standard AS5601-2004, noting required height and clearance
regulations.
The RH530LEDG Rangehood can be installed via overhead or side mounting. Holes required MUST be
measured and marked prior to any alteration to cabinet
Option 1. Overhead Mounting
1. Remove filters
2. Locate holes in the top of the Rangehood
3. Connect rangehood power wires to pre-installed RV wiring using the 12 volt DC power source
(Wires are labelled +/- take care to ensure connection is completed correctly)
4. Lift Rangehood into designated position and locate pre-marked holes
5. Use 4 x Stainless Steel screws only into locating holes (shown above)
6. Install filters
7. NCE recommends that after mount, power on and test all functions
Option 2. Side Mounting
1. Remove filters
2. Locate holes in the top of the Rangehood
3. Connect rangehood power wires to pre-installed RV wiring using the 12 volt DC power source
(Wires are labelled +/- take care to ensure connection is completed correctly)
4. Lift Rangehood into designated position and locate pre-marked holes
5. Use 4 x Stainless Steel screws only into locating holes (shown above)
6. Install filters
7. NCE recommends that after mount, power on and test all functions
Edited with the trial version of
Foxit Advanced PDF Editor
To remove this notice, visit:
www.foxitsoftware.com/shopping