User Manual

Page 3
Safety equipment in the NBB-radio remote control:
In thetransmitter
In thereceiver:
Ifthe NBBradio remotecontrol is not used for a long period,it is urgently recom-
mended that the batteries be charged now and again (about every 4 weeks).
This prevents deep discharges of the batteries and prolongs their useful life. If
you shut down the NBB radio remote control for a long period, we recommend
you take the battery out of the transmitter.
Frequency change:
ACCIDENT RISK!
EMERGENCY STOP check
Checking theLED'sat the receiver PNN-BUS-3:
LED1:
LED2:
LED3:
LED4:
LED5:
,thiscomprisesmainly:
EMERGENCY STOP with automatic disconnection of the power supply.
Automatic zeropositioning.
Two diversity units for evaluation of the EMERGENCY STOP signal.
Automatic zerosetting when switching back on after radio interruption.
Locking of the radio commands at relay level in the event of a defective EMERGENCY
STOP circuit.
To ens ure fault-fre e o peration , please follow precise ly the f oll owing rule s f or ope rati on :
The unit to be controlled can only be switched on - it is assumed that the transmitter is
ready to operate - when no command unit is actuated. The command necessary to do so
is triggered by the key "ON/HORN". This triggers a horn signal in the unit to be controlled.
After switch-on of the facility to be controlled, this key is used for repeated emission of the
hornsignal inaccordancewithworkingregulations.
To change the freque nc y, keep the "ON/HO RN " key pressed down. Th en o perate the "FRE-
QUENCY CHANGE"key. Ifthereceiverlocks into the new frequency, a horn signal is given
(if present) and the unit to be controlled is ready for operation.
(Please observe the particular postal approval regulations of the concerned country.)
To m aintain operational safety, a regular function check of the NBB radio remote control is
necessary. In single-shift day-to-day operation, we recommend performing this check at
least once a week. Checking is possible using the display lights provided on the receiver.
To do s o, the tran sm itter mus t be s et to the ready- to-oper ate state.
First connect just the receiver - the transmitter remains switched off.
Activate the transmitter by unlocking the EMERGENCY STOP switch.
Now check the commands (always start with the lowest stage) and check for
correct reaction of the unit to be controlled.
Ensureinparticularthatthereisnobodyinthedangerarea.
.PresstheEMERGENCYSTOPswitchatthetransmit-
ter until the switch engages. Then observe if the unit to be controlled is switched
off (time to switch off according to the application).
POWER ON. If LED fails to come on, check the power supply.
If the power lead is OK, call in the after-sales service.
HF PRESENT. Steady light when transmitter is switched on
(insignificant for scanner operation).
Flashes evenly during fault-free operation.
Irregular flashing means that the HF channel is probably at fault -
please set another channel.
IfthisLEDcomeson,theHFchannelisatfault.
Charge condition display of battery (only present when charger is
integrated). Steady light when charging a battery.
LED flashes: The battery is charged, the charging process is finished.
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
FREQUENCY CHANGE
6. OPERATING THE UNIT
7. FUNCTION CHECK
®
MADE IN GERMANY
®
ZULASSUNG - TYPE APPROVAL - AGREMENT - HOMOLOGATION
I
SYSTEM
NON EU COUNTRIES:
AUS
CDN
CH
CZ
H
IS
KO
N
no approval necessary
2634231 116A /
2634231 116
BAKOM 95.0720.K.P
45251983
MÜ-40.039-083/96
IS-3236-00
93335
NO96000433-R/
NO95000545-R
1027 /96
YK33-9806
K9VPO C90 T001 /
K9VPNN3-5R00 1 /
O5RS-DE96AO
3K43 D/3R1B9/
SPLS/RX- 439/98
PL
TJY
USA
ZA
1
2
3
4
5
TYPE:
SERIAL NO.:
HF MODULE:
FREQUENCY:
PNN -BU S-3
999 899 4990
S-EM01A0
BAND F
EU COUNTRIES:
X0560