® OPERATING INSTRUCTIONS HyPro-6 USA HyPro-8 USA R-16, R-CAN Compact-M, Compact-V Receiver Type / Version Transmitter Type / Version Factory No. Factory No.
1. STANDARD SPECIFICATION % % % Portable transmitter. Receiver with integrated mounting holes. Optional: Multi-pin connecting cable for the receiver according to your specifications. The actual delivery specification is as detailed on the confirmation of order or the delivery note accompanying the goods! 2. SAFETY PRECAUTIONS Even if you are accustomed to working with radio control systems, read these operating instructions carefully before using this equipment.
DISPLAY AKKU DISPLAY FUNK ON STOP 3. TRANSMITTER HyPro START When the red "Battery" indicator lamp lights up, the batteries (rechargeable or not rechargeable) are nearly empty. The transmitter can be operated for approximately 30 minutes more in this condition. During this time, bring the unit to a safe position, switch off the transmitter and install 2 charged AA Mignon batteries 1,2V NiMH (or batteries 1,5V - not rechargeable).
. RECEIVER R-16, R-CAN Compact-M, Compact-V R-16 Mounting possibility of the receiver R-16, R-CAN or the Compact-M. R-CAN Compact-M Compact-V The receiver is connected to the unit to be controlled with the multi-pin connecting cable supplied.
Safety equipment in the NBB-radio remote control: 5. OPERATING THE UNIT In the transmitter, this comprises mainly: % STOP, resp. EMERGENCY STOP with automatic disconnection of the power supply. % Automatic zero positioning. In the receiver: % Two diversity units for evaluation of the STOP, resp. EMERGENCY STOP signal. % Automatic zero setting when switching back on after radio interruption. % Locking of the radio commands at relay level in the event of a defective STOP, resp.
To maintain operational safety, a regular function check of the NBB radio remote control is necessary. In single-shift day-to-day operation, we recommend performing this check at least once a week. Checking is possible using the display lights provided on the receiver. To do so, the transmitter must be set to the ready-to-operate state. 6. FUNCTION CHECK % % % % % Checking the LED display at the receiver R-16 and R-CAN: (Optional with integrated charger) RADIO PRESENT.
. RATING PLATES The rating plates state the type of transmitter or receiver, the factory number, the frequency range and the approval number for non EU countries. Always state the factory number in all your queries. Example: 8. MAINTENANCE Your NBB radio remote control is largely maintenance-free. Nevertheless, please bear in mind the following points: % The STOP key, resp.the EMERGENCY STOP switch must be easy to move.
11. FCC NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
TECHNICAL DATA ® Operating ambient temperature -20 to +70 °C Insulation class - Protection IP 65 TRANSMITTER HyPro-6, HyPro-8 Transmission frequency range 433.1 - 434.75 MHz (The actual frequency range depends on the regulations of the concerning country !) The use of synthesizer technology permits frequencies to be selected in accordance with the appropriate waveband for the country of use.
Page 9
APPROVALS AND CERTIFICATES ® Obtainable at demand: M-Zert mbH Certificate DIN EN ISO 9001:2000-12 No. 03022 © NBB Controls + Components AG Otto-Hahn-Straße 3-5 DE-75248 Ölbronn-Dürrn Tel.: 0 72 37 / 9 99 - 0 Fax: 0 72 37 / 9 99 - 1 99 eMail: sales @ nbb.de http://www.nbb.de We reserve the right to alter specifications without notice. Bedienungsanleitung HyPro-6, HyPro-8, R-16, R-CAN, Compact-M, Compact-V, Englisch, Teile-Nr. 3.150.1251, Stand 11.
