NAVIGON 92 Plus NAVIGON 92 Premium User’s manual English (United Kingdom) August 2011
The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-oflife. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal waste. Imprint NAVIGON AG Schottmüllerstraße 20A D-20251 Hamburg The information contained herein may be changed at any time without prior notification.
User’s manual NAVIGON 92 Plus | 92 Premium Table of contents 1 Introduction .......................................................................................7 1.1 1.2 1.3 2 About this manual ................................................................................ 7 1.1.1 Conventions.......................................................................... 7 1.1.2 Symbols................................................................................ 7 Legal notice .........................
User’s manual NAVIGON 92 Plus | 92 Premium 7.2 7.3 7.4 8 Specifying a destination ..................................................................... 27 7.2.1 Specifying the country in which the destination is situated ............................................................................... 28 7.2.2 Enter an Address ................................................................ 28 7.2.3 Announcing the address ..................................................... 30 7.2.4 Points of interest .
User’s manual NAVIGON 92 Plus | 92 Premium 9 Useful functions ..............................................................................65 9.1 9.2 9.3 9.4 9.5 9.6 9.7 10 Route Profiles .................................................................................... 65 9.1.1 Route profile settings .......................................................... 65 9.1.2 NAVIGON basic profiles ..................................................... 65 9.1.3 Creating a new route profile .................
User’s manual NAVIGON 92 Plus | 92 Premium 10.5 10.6 10.7 During a call ...................................................................................... 96 10.5.1 Go back to entering a destination........................................ 96 10.5.2 Moving the map to the foreground ...................................... 96 10.5.3 Entering numbers ............................................................... 96 10.5.4 Muting the microphone .......................................................
User’s manual NAVIGON 92 Plus | 92 Premium 1 Introduction 1.1 About this manual 1.1.1 Conventions For better legibility and clarification, the following styles are used in this manual: Bold and italics: Names of products SMALL CAPITALS: Names of windows and dialogue boxes Bold: Highlighting of important parts in the text Underlined: Descriptions of buttons, input boxes and other elements on the user interface Underlined and italics: Names of control elements on the navigation device 1.1.
User’s manual NAVIGON 92 Plus | 92 Premium 1.2.2 Trade marks All brand and trade marks mentioned in this document and registered by third parties are subject without reservation to copyright law and the proprietary rights of their respective owners. All trade marks, trade names and company names used in this document are or may be trade marks or registered trademarks of their respective owners. All rights reserved except those explicitly granted.
User’s manual NAVIGON 92 Plus | 92 Premium 2.2 Description of the navigation device 1 On/Off 2 Touch-screen 3 Microphone (only NAVIGON 92 Premium) 4 Mini USB socket for USB cable / mains adapter 5 Slot for microSD memory card 6 Reset 7 LED 2.3 Important safety information In your own interest, please read the following safety information and warnings carefully before starting up your navigation system. 2.3.1 Navigation safety information Use the navigation system at your own risk.
User’s manual NAVIGON 92 Plus | 92 Premium Caution! Traffic regulations have priority over any instructions from the navigation system. Caution! Follow the instructions of the navigation system only when the circumstances and the road traffic regulations allow you to do so! The navigation system will still guide you to your destination even if you deviate from the calculated route. Caution! Check that the cradle is secured and adjusted properly before each journey. 2.3.
User’s manual NAVIGON 92 Plus | 92 Premium Caution! Do not attach the cradle within the working zone of any airbags. Caution! Do not fasten the cradle too close to the steering wheel or other controls. The driver must not be obstructed in operating any car functions. Caution! When installing the cradle, make sure that it will not pose a risk in the event of an accident.
User’s manual NAVIGON 92 Plus | 92 Premium 1. Clean the suction cup and that part of the windscreen to which you want to secure the cradle. Both must be dry and free of dirt and grease. 2. Open the lever on the suction cup as far as possible. 3. Place the cradle suction cup against the windscreen. 4. Press the lever towards the windscreen. Inserting the navigation device into the cradle On the back of the navigation device you will see a circle with two recesses. 1.
User’s manual NAVIGON 92 Plus | 92 Premium Caution! Be sure to refer to all the safety information in chapter "Important safety information" on page 9. Note: Insert the USB connector securely in the corresponding USB sockets! Note: It takes approx. 3 hours to charge the device when the battery is flat. A fully charged battery enables up to 2 hours of use depending on the device configuration. TMC antenna The navigation device has an integrated TMC receiver.
User’s manual NAVIGON 92 Plus | 92 Premium Once the navigation device has determined your position, this position can be used as a starting point for calculating a route. The map data on your navigation device includes the geographical coordinates of all digitally recorded points of interest, streets and places. This enables the device to calculate a route between a starting point and a destination.
User’s manual NAVIGON 92 Plus | 92 Premium ► ► ► 3.3 In the NAVIGATION window tap on (More) > System Settings > Power and Screen > Automatic Standby. Select after how much time you want the navigation device to be switched to standby mode (Never, After 10 mins., After 20 mins., After 30 mins.). Select Power Loss in order to switch the device to standby mode when the external power supply is interrupted.
User’s manual NAVIGON 92 Plus | 92 Premium ► DD: the day in 2 digits 8. Tap on OK. If you purchased your navigation system together with the add-on NAVIGON Safety Camera, the WARN OF SAFETY CAMERAS window will open. 9. Read the text in this window very carefully. It describes the settings which you can make for the add-on. 10. Tap on OK. The WARN OF SAFETY CAMERAS window opens. 11. Select the setting you want. 12. Tap on OK.
User’s manual NAVIGON 92 Plus | 92 Premium Note: In the NAVIGATION windw tap on (More) > Show Introduction if you want to see the introduction again later. A window with the following message opens: "Please note that the road traffic regulations are prior to the instructions of the navigation system. Please do not operate the device while driving." 16. After you have read and fully understood the message, tap on OK.
User’s manual NAVIGON 92 Plus | 92 Premium (Navigation Options): Opens the NAVIGATION OPTIONS window; in it you will find useful functions for navigation and for adjusting the map. 5.1 Switching to a different application Switching between applications is possible in various ways. 5.1.1 Scrolling Drag your finger horizontally over the screen in order to scroll between the applications. ► ► 5.1.
User’s manual NAVIGON 92 Plus | 92 Premium No Signal: Data is being received from less than three satellites. Position cannot be calculated. GPS Ready: Data is being received from at least 3 satellites. Position can be calculated. Simulation: If a simulation is in progress, the Demo symbol will appear instead of the GPS symbol. For details of the GPS status refer to chapter "GPS Status, saving the current location" on page 74.
User’s manual NAVIGON 92 Plus | 92 Premium The TMC symbol can display the following TMC reception status: Tuning (in red): The TMC receiver is operational but cannot find a transmitter that is sending TCM signals. There are no active traffic messages. Tuning: The TMC receiver is operational but cannot find a station that is transmitting TMC signals. Traffic messages are active however. This can be the case, for example, when travelling through a tunnel.
User’s manual NAVIGON 92 Plus | 92 Premium Muting The Muting symbol can indicate the following states: No symbol: The navigation application is not muted. Muting: The navigation application is muted. If the device is navigating at the moment, you will not hear any driving instructions. Note: This symbol indicates only the muted state of the navigation instructions. It says nothing about the volume of the hands-free module. 5.
User’s manual NAVIGON 92 Plus | 92 Premium Right key: / : Switches between the keyboard for special characters and the keyboard for numbers. Note: The layout for the keyboard with the Latin alphabet can be configured. ► ► 5.3.3 In the NAVIGATION window tap on (More) > System Settings > Language and Keyboard > Keypad layout (Latin). Select the layout you want to use: Alphabetical (ABCDEF), English (QWERTY), German (QWERTZ), French (AZERTY).
User’s manual NAVIGON 92 Plus | 92 Premium Greek keyboard layout Left key: / : Switches between the Latin and Greek keyboard layout. Right key: Switches between the keyboard for special characters, the keyboard for numbers and the keyboard for letters of the current keyboard layout. 5.3.4 Entering data Often you can select an entry from a list. This is the case, for example, when you enter a location.
User’s manual NAVIGON 92 Plus | 92 Premium Note: The Voice Command function is not available in every language. For languages in which this function is not available, the Voice Command button is not shown in the NAVIGATION window. Many functions of your navigation device can be called up conveniently by voice command. 6.1 Activating the voice commands function The voice commands function is automatically active in many windows.
User’s manual NAVIGON 92 Plus | 92 Premium 6.3 Help Say only "Help" if you want to know which voice commands are currently possible. In nearly all windows in which voice commands are supported the navigation system will then tell you which commands you can say in the current window. 6.4 Deactivation of the voice commands function The voice commands function will be deactivated under the following conditions: ► ► 6.
User’s manual NAVIGON 92 Plus | 92 Premium 7 Navigation Use the navigation system at your own risk. Caution! Be sure to refer to all the safety information in chapter "Important safety information" on page 9. Impaired GPS reception If GPS reception is impaired (e.g. because you are in a tunnel), navigation will be continued. The navigation system will then calculate your likely position from the route data and your previous driving profile.
User’s manual NAVIGON 92 Plus | 92 Premium The integrated GPS receiver is not initialised for the first time until the navigation application is started for the first time. It can take up to 20 minutes to initialise the GPS receiver for the first time. Each time you switch on the navigation device after this, GPS reception will start within a short time. If the navigation device has not been switched on for more than a week, it can take up to 10 minutes to re-initialise the receiver.
User’s manual NAVIGON 92 Plus | 92 Premium ► select a point of interest (see "Points of interest" on page 31). Note: If you are entering a new destination for the first time, the COUNTRY window opens. Tap on the country in which your destination lies. To select a saved destination you can select from the following lists of destinations and addresses: ► FAVOURITES: All destinations that you have entered and then saved (see "Favourites" on page 35).
User’s manual NAVIGON 92 Plus | 92 Premium ► Select the order of entry you want (Street First or City First). If you would like to save this setting permanently and without being asked again, first activate the checkbox alongside 'Use these settings in future for address information'. Note: You can define and change the order in the NAVIGATION window under (More) > Navigation Settings > General > Input Mode for Address Data.
User’s manual NAVIGON 92 Plus | 92 Premium If the entered house number is not included on the map, the window will show an address with the house number closest to the one entered. The system calculates the route. When the route calculation is finished, the map opens in Route preview mode. The destination is indicated on the map. A description of all the options available in the DESTINATION window can be found in the chapter "Options in the Destination window" on page 38.
User’s manual NAVIGON 92 Plus | 92 Premium A single signal tone and the symbol (Speak) indicate that the navigation system is waiting for your voice command. 2. Follow the instructions given by the navigation system. When you have finished entering the address, the map will open in Route preview mode. The destination is indicated on the map. Note: The Voice Command function is not available for every language.
User’s manual NAVIGON 92 Plus | 92 Premium The DESTINATION list opens. It contains the nearest POIs in the specified category, sorted by distance. 4. If the list is very long: ► Tap on (Close List). The keyboard appears. ► Enter a number of letters from the destination. ► Tap on (Open List). The list now contains only those destinations which begin with the letters entered. 5. Tap on the name of the destination. The DESTINATION window opens. 6.
User’s manual NAVIGON 92 Plus | 92 Premium The DESTINATION list opens. It contains POI from the specified category, sorted alphabetically. 5. If the list is very long: ► Tap on (Close List). The keyboard appears. ► Enter a number of letters from the destination. ► Tap on (Open List). The list now contains only those destinations which begin with or contain the letters entered. 6. Tap on the name of the destination. The DESTINATION window opens.
User’s manual NAVIGON 92 Plus | 92 Premium The CATEGORY window opens. 2. Select a category from which you would like to find a POI. If sub-categories exist for the category you have selected, the Sub Category list opens. 3. Select the sub-category from which you would like to select a POI. The DESTINATION list opens. It contains the POI from the selected category, sorted alphabetically. 4. If the list is very long: ► Tap on (Close List). The keyboard appears.
User’s manual NAVIGON 92 Plus | 92 Premium ► Tap on (Information). The INFORMATION window opens. It contains all the information about the specified destination that is stored in the navigation system's database. ► ► ► ► Tap on Close in order to close the INFORMATION window again. Tap on map. (Show on Map) in order to see the destination on the Tap on (Save) in order to save the destination in the FAVOURITES list.
User’s manual NAVIGON 92 Plus | 92 Premium Note: Favourites are indicated on the map by a small flag with their name. In the NAVIGATION window tap on (More) > Navigation Settings > Map Display. Under Show Favourites select whether you want them to be indicated on the map or not (Yes or No). 7.2.7 Last Destinations The last 12 destinations to which you have navigated are saved by the navigation system in the LAST DESTINATIONS list. 1. In the NAVIGATION window, tap on Enter Destination > Last Destinations.
User’s manual NAVIGON 92 Plus | 92 Premium 4. Tap on Start Navigation in order to navigate to the stipulated address. - or Tap on (Parking) in order to search for and navigate to a car park near your destination. The system calculates the route. When the route calculation is finished, the map opens in Route preview mode. The destination is indicated on the map. For detailed information on how to start navigation, please refer to chapter "Route preview" on page 39. Please read on there. 7.2.
User’s manual NAVIGON 92 Plus | 92 Premium The destination point is represented on the map by a pin needle ( ). The corresponding address or the geographical coordinates of the destination point are shown in the Destination Info box. 5. Tap on the Destination Info box. The DESTINATION window opens. 6. Tap on Start Navigation in order to navigate to the stipulated address. - or Tap on (Parking) in order to search for and navigate to a car park near your destination. The system calculates the route.
User’s manual NAVIGON 92 Plus | 92 Premium Home Address: Saves the selected point as your home address. 7.2.12 Route preview The map is open in Route preview mode. The navigation destination is depicted by a small flag. For detailed information refer to the chapter "Map in Route preview mode" on page 53. Route Profile The route is calculated on the basis of a route profile. The current route profile is indicated at the top right edge of the map on the Profile) button.
User’s manual NAVIGON 92 Plus | 92 Premium Note: Even when the MyRoutes function is activated, sometimes only one additional route or no additional routes at all can be calculated for the selected destination. No further suggestion is then shown on the button in question. Activate MyRoutes You can specify whether you want several routes to be available for selection before the navigation starts. In the NAVIGATION window tap on (More) > Navigation Settings > General.
User’s manual NAVIGON 92 Plus | 92 Premium 2. In the button bar tap on (Navigation Options) or (Navigation). 3. Tap on Stop Simulation. No GPS reception If GPS signal reception is not good enough, the following message will appear: "GPS reception is currently not sufficient. Navigation starts automatically as soon as GPS reception is OK again." You have the following options: ► ► ► Wait.
User’s manual NAVIGON 92 Plus | 92 Premium You have selected a destination from the LAST DESTINATIONS list or from the FROM THE PHONE BOOK list (see "Last Destinations" on page 36 or "From the phone book" on page 36). The DESTINATION window is open. 1. In the DESTINATION window tap on (Save). The NAME OF THE DESTINATION window opens. 2. Enter a name for the destination. 3. Tap on Save. 7.3.
User’s manual NAVIGON 92 Plus | 92 Premium 2. Tap on Favourites. 3. in the FAVOURITES window tap on (More) > Edit. The EDIT FAVOURITES window. 4. Tap on the (Rename) button to the right of the destination you want to rename. 5. Enter a new name. 6. Tap on Save. 7.3.4 Defining the home address You can always start navigation to your home address very quickly by tapping in the NAVIGATION window on Take Me Home. You can define exactly one destination as your home address.
User’s manual NAVIGON 92 Plus | 92 Premium Note: Any destination which you have entered or selected while specifying a destination can easily be defined as the home address. In the DESTINATION window tap on (More) > Home Address to save the selected destination as the new home address. 7.4 Multi-leg routes It is possible to plan routes without GPS reception, for example in the comfort of your home. Planned routes can be saved for later use.
User’s manual NAVIGON 92 Plus | 92 Premium If you want to enter your current location as the starting point: 2. Tap on Current Position. 3. In the DESTINATION window tap on Add. If you want to enter a different starting point: 2. Tap on the button for how you want to enter the destination. 3. Enter the starting point according to the relevant section in chapter "Specifying a destination" on page 27. 4. In the DESTINATION window tap on Add. The ROUTE PLANNING window opens again.
User’s manual NAVIGON 92 Plus | 92 Premium Changing the order of the route points 1. in the ROUTE PLANNING window tap on Route. (More) > Edit The EDIT ROUTE window opens. 2. Tap on the (Route Point Down) button to shift the selected route point further to the back (example: route point 2 becomes route point 3). - or Tap on the (Route Point Up) button to shift the selected route point further to the front (example: route point 3 becomes route point 2).
User’s manual NAVIGON 92 Plus | 92 Premium The destination is now saved to the SAVED ROUTES list. The ROUTE PLANNING window is opened. Loading routes 1. Open the ROUTES window (see "Opening the route planning" on page 44). 2. Tap on Load Route. The LOAD ROUTE window opens. It shows all the saved routes in alphabetical order. 3. Tap on the route that you want to load. The ROUTE PLANNING window opens. The starting point and the route points of the loaded route have been entered.
User’s manual NAVIGON 92 Plus | 92 Premium 5. Confirm with Yes the question whether you really want to delete the route. Deleting the complete Saved Routes list 1. Open the ROUTES window (see "Opening the route planning" on page 44). 2. Tap on Load Route. The LOAD ROUTE window opens. 3. in the LOAD ROUTE window tap on Routes. (More) > Delete All 4. Confirm with Yes the question whether you really want to delete all the saved routes.
User’s manual NAVIGON 92 Plus | 92 Premium The starting point and the route points are marked by flags. The distance and the estimated trip time is given for each leg of the route. 7.4.7 Simulating routes It is also possible simply to simulate navigation on a planned route. Note: GPS reception is not necessary for simulation. If you have planned a multi-leg route, only the first leg will be simulated.
User’s manual NAVIGON 92 Plus | 92 Premium Route Profile The route is calculated on the basis of a route profile. The current route profile is indicated at the top right edge of the map on the Profile) button. (Route Route profiles take account of the characteristics and special aspects of the different modes of transport. For example a route profile for bicycles will exclude motorways from the route calculation but will include roads which other vehicles are not allowed to use.
User’s manual NAVIGON 92 Plus | 92 Premium ► In the NAVIGATION window tap on (More) > Navigation Settings > General. Under Activate MyRoutes select whether you want the MyRoutes function to be available or not (Yes or No). Start Navigation ► Tap on the button of the route which you want to use for the navigation.
User’s manual NAVIGON 92 Plus | 92 Premium Under the following circumstances the map switches automatically to Standard mode: ► ► You begin a trip while the NAVIGATION window is open. The switch takes place after only a short while. You reach the destination of a navigation in Vehicle mode. To open the map: ► In the button bar tap on (Show Map). Note: If GPS reception is not good enough to determine your current position, your last position will be indicated.
User’s manual NAVIGON 92 Plus | 92 Premium A window opens with several buttons which you can use to access the most important functions for the map. Traffic: Opens the TRAFFIC window in which active traffic messages are listed (see "TMC (Traffic Information)" on page 75). Day/Night: Changes between "Day" and "Night" screen modes. MyReport: Opens the MYREPORT window. Here you can notify NAVIGON about any changes to traffic monitoring systems and routing. 2D/3D: Changes between 2D and 3D mode.
User’s manual NAVIGON 92 Plus | 92 Premium 1 When the MyRoutes function is activated, up to three numbered routes are indicated on the map in different colours (orange, green, blue). In the following cases only one route is shown: ► 2 The MyRoutes function is deactivated (see "MyRoutes" on page 39). ► You have planned a route with more than one route point. ► A route profile with the Pedestrian speed profile is active. The destination is marked with a little flag.
User’s manual NAVIGON 92 Plus | 92 Premium ► 8.4 Tap on map. (Show on Map) to show the calculated route(s) on the Map in Navigation mode How you are guided to your destination depends on various factors (the route profile selected, your current location, the type of route planning, traffic information along the route, etc.). Your navigation system automatically selects the optimum method. 8.4.1 Navigation in Vehicle mode After the route was shown in Route preview mode, navigation was started.
User’s manual NAVIGON 92 Plus | 92 Premium 6 The large arrow box shows a diagram of the next junction which you should turn on to. The distance remaining to this junction is indicated underneath. As you get closer to the junction you will see a progress bar in addition to the distance: The nearer you get to the junction, the more yellow spots are displayed. If you don't have to change direction for a long time, you will see only a straight arrow.
User’s manual NAVIGON 92 Plus | 92 Premium 9 When you get close to your destination, the Parking button will appear. When you tap on the Parking button, the OPTIONS window opens and you have two options: ► ► You can select a car park from where you can then continue on foot. When you have parked your vehicle, you can save the current position and continue the navigation on foot. For a description of the Parking function refer to chapter "Parking near the destination" on page 68.
User’s manual NAVIGON 92 Plus | 92 Premium ► Tap on (Destination search) to view the map in Destination search mode (see "Map in Destination search mode" on page 62). Button bar For easier and quicker orientation on the map, the button bar is hidden in Navigation map mode. ► Tap on any point of the map to show the bar with the buttons. The button bar is hidden again automatically after a short while. Volume The volume of the spoken driving instructions can be adjusted during navigation. 1.
User’s manual NAVIGON 92 Plus | 92 Premium The Reality View mode shows with greater clarity the signposting and lanes you must follow. This display does not change until you have passed the spot indicated. The map will then change back to Navigation mode. ► If you want to change to Navigation mode before then, just tap on any point on the map. Note: The Reality View mode is not available for all motorway junctions and three-leg motorway junctions. Availability depends on the map material used. 8.4.
User’s manual NAVIGON 92 Plus | 92 Premium ► ► If you are navigating on a route and more route points are still to follow, navigation to the next route point will be started immediately after the message. Traffic messages are not taken into account. Note: In pedestrian mode you must take care to hold the device without covering it at the top. The GPS receiver is located there and its reception could be impaired.. 1 The direction in which your destination lies is indicated (red triangle).
User’s manual NAVIGON 92 Plus | 92 Premium Zoom In: The map section becomes smaller, but you will see more details. Centre the position: During pedestrian navigation you can shift the visible map section in order to view the surrounding area on the map. This may mean that your current position can no longer be seen on the visible section of the map. ► Tap on the Centre the position button if your current position can no longer be seen on the visible section of the map.
User’s manual NAVIGON 92 Plus | 92 Premium MyRoutes: Opens the map in Route preview mode. You are provided with up to three different suggestions as to how you can continue your journey. Select one of the routes offered. 2D/3D: Changes between 2D and 3D mode. Country Info: Opens a window with important traffic regulations of the country in which you are currently travelling (e.g. speed restrictions, blood alcohol limits etc). Route Profile: Opens the ROUTE PROFILES window.
User’s manual NAVIGON 92 Plus | 92 Premium 8.5.1 Changing the map section The following options for searching for and displaying destinations and other information on the map are available: With your finger: You can shift the map in any direction you want with your finger. With the buttons at the bottom edge of the screen: Zoom Out: The map section shown becomes larger, but you will see fewer details. Zoom In: The map section shown becomes smaller, but you will see more details.
User’s manual NAVIGON 92 Plus | 92 Premium 8.5.2 Set destination 1. Tap on the point of the map which you want to set as the destination point. The point which you have selected will be indicated on the map in central position. 2. Tap on Set destination. The destination point is represented on the map by a pin needle ( ). The corresponding address or the geographical coordinates of the destination point are shown in the Destination Info box.
User’s manual NAVIGON 92 Plus | 92 Premium 9 Useful functions 9.1 Route Profiles Route profiles define the characteristics and special aspects of the different modes of transport which are to be taken into account when calculating routes. For example a route profile for bicycles will exclude motorways from the route calculation but will include roads which other vehicles are not allowed to use. And different arrival times will be calculated for a bicycle than for a motorcycle for example. 9.1.
User’s manual NAVIGON 92 Plus | 92 Premium Lorry Motorbike Car The speed profile of a basic profile cannot be changed. You can adapt the other settings to your requirements. Basic profiles cannot be renamed or deleted. To have a choice of different profiles for example for several cars, you can create your own route profiles. 9.1.3 Creating a new route profile You can create your own route profiles.
User’s manual NAVIGON 92 Plus | 92 Premium 9.1.5 Managing route profiles User-defined route profiles can be edited, renamed and deleted. Editing a route profile 1. In the button bar tap on (Navigation Options) > Route Profile. The ROUTE PROFILES window opens. 2. Tap on the to edit. (List) button alongside the route profile that you want 3. Make the required settings. 4. Tap on OK. The Use of Toll Roads setting is comprised of several individual settings.
User’s manual NAVIGON 92 Plus | 92 Premium The ROUTE PROFILES window opens. 2. Tap on (More) > Edit. 3. Tap on the (Delete) button alongside the route profile that you want to delete. 4. A dialog window prompts you to confirm deletion. 5. Tap on Yes. Note: Basic profiles cannot be deleted. 9.2 Screenshots You can create and save screenshots of the content currently shown on the screen at any moment. 9.2.1 Enabling screenshots 1.
User’s manual NAVIGON 92 Plus | 92 Premium The following scenarios are imaginable: Continuing on foot You see a car park, park your vehicle and want to continue to the destination on foot. 1. Tap on the (Parking) button. The OPTIONS window opens. 2. Tap on Pedestrian mode. The following message appears: "Your current position has been saved. You will find it in the 'Favourites' list as 'My Vehicle'. This enables you to easily find the way back to your vehicle." 3. Tap on OK.
User’s manual NAVIGON 92 Plus | 92 Premium The navigation continues to guide you to the destination in Pedestrian mode. Back to the destination You have reached your destination. Navigation has ended. For some reason, however, you carry on driving, perhaps because you were unable to find a place to stop. Now you want to be guided back to the destination. 1. Tap on the (Parking) button. 2. Tap on Last Destination.
User’s manual NAVIGON 92 Plus | 92 Premium The navigation system now guides you in Pedestrian mode to the place where you parked your vehicle. As soon as you get near to your vehicle, the (Vehicle reached) button appears at the left edge of the screen. 1. Get into your vehicle and place the navigation device into its cradle. 2. Tap on the (Vehicle reached) button. The navigation system will now guide you to the destination of the next stage in the mode corresponding to the selected route profile.
User’s manual NAVIGON 92 Plus | 92 Premium It shows symbols of the 3 stipulated categories of POI. The distance to the nearest POI in each category is indicated. The small orange triangle alongside the route indicates in addition whether the POI lies on the right ( ) or on the left ( ) in driving direction. Note: The POI on Your Route bar closes after a few seconds. If you want the bar to remain open, tap on the button changes to (Fix) button. The (Fixed). 2.
User’s manual NAVIGON 92 Plus | 92 Premium 5 Additional information about each POI in the list can be displayed. ► 9.4.2 Tap on the (Information) button on the right alongside the corresponding POI (refer also to "Information about the destination" on page 34). Navigating to one of the destinations ► Tap in the list on the destination to which you want to navigate. The selected destination will be inserted as an interim destination. The system recalculates the route.
User’s manual NAVIGON 92 Plus | 92 Premium 9.5 GPS Status, saving the current location In the GPS STATUS window you will find an overview of the data the navigation system calculates from the GPS signals it receives. ► In the button bar tap on Status. (Navigation Options) > GPS On the left side you will see a map section with your current position shown at the centre. When you move, the map section will change in accordance with your current position.
User’s manual NAVIGON 92 Plus | 92 Premium Unblocking a route section ► In the button bar tap on Unblock. (Navigation Options) > The block will be lifted and the route recalculated. 9.7 TMC (Traffic Information) The integrated TMC receiver enables the navigation system to make use of current traffic messaging. If necessary it can change your route dynamically, for example in order to avoid a traffic jam. Note: TMC is available free of charge in many European countries.
User’s manual NAVIGON 92 Plus | 92 Premium Note: You can configure whether to show only traffic obstructions with more than 20 minutes time loss or also obstructions with less time loss (see "Settings (Traffic Information)" under "Announce Traffic Events" on page 83). ► Tap on (Traffic Information). The TRAFFIC OBSTRUCTION window opens. The window shows a map section with the route section affected by the message and with the optimised route which avoids the reported traffic obstruction.
User’s manual NAVIGON 92 Plus | 92 Premium In this case the navigation system checks whether it is worth returning to the original route. If it is, the will appear. ► (Traffic incident cleared) button Tap on (Traffic incident cleared) to open the TRAFFIC OBSTRUCTION window (see above). You can then decide whether you want to return to the original route (Yes) or not (No). If you do not tap on (Traffic incident cleared, you will be returned automatically to the original route after about 15 seconds. 9.
User’s manual NAVIGON 92 Plus | 92 Premium The following message appears: ► ► 9.7.3 Tap on OK to close the message.. Tap on Details to open the TRAFFIC window (see "Displaying traffic information" on page 78). Displaying traffic information You can have the currently available traffic messages displayed at any time. ► In the button bar tap on (Navigation Options) > Traffic. The TRAFFIC window opens. You can use the of messages.
User’s manual NAVIGON 92 Plus | 92 Premium 1 The Filter filter shows how many traffic messages there are altogether, what type of traffic message is listed, and how many messages of this type there are. ► Tap on the Filter button to select the messages you want displayed (see "Filtering traffic messages" on page 80). 2 When a new traffic obstruction affecting your route is reported, it is marked with 'NEW'. 3 This mark indicates that the message in question comes from a PremiumTMC provider.
User’s manual NAVIGON 92 Plus | 92 Premium Note: Most radio stations report only traffic obstructions in their own country. 7 Here the reported obstruction is displayed as a traffic sign. 8 Here you can see on which section of the road the obstruction lies. 9 The navigation system can either Detour ( ) or Ignore°( ) obstructions along the route. The symbol indicates the respective status.
User’s manual NAVIGON 92 Plus | 92 Premium The affected route section is presented in the left half of the window. The distance, the length of the obstruction and the anticipated time loss are indicated. The content of the message is shown in the right half. The navigation system announces the traffic message in question if the detail view is open. Reading out text messages is not possible in all languages however. Note: You can configure the reading out function.
User’s manual NAVIGON 92 Plus | 92 Premium Note: Intervening manually in the calculation of detours can have undesirable consequences: ► The travelling distance may be longer than necessary ► The travelling time may be longer than necessary 1. Open the TRAFFIC window (see "Displaying traffic information" on page 78). 2. In the TRAFFIC window tap on (More) > Edit Mode. 3. Tap on Yes. The TRAFFIC window opens again.
User’s manual NAVIGON 92 Plus | 92 Premium Detour All: (available only when edit mode is activated): Sets all the traffic messages along the route to the status Detour. Calculate Optimised Route: (available only when edit mode is activated): Sets all the traffic messages along the route to the status 'New'. On this basis the navigation system will calculate an 'Optimised Route' and will assign to each traffic message the status which results from the calculation (Detour or Ignore). Info: 9.7.
User’s manual NAVIGON 92 Plus | 92 Premium 10 Handsfree Module This chapter is relevant for you only if your navigation device is a NAVIGON 92 Premium. The navigation device has a hands-free module which supports Bluetooth connections to Bluetooth-capable mobile phones and headsets. It can be connected simultaneously to up to two mobile phones or to a headset. If you have set up a connection to a mobile phone, you can use the navigation device as a hands-free module for it.
User’s manual NAVIGON 92 Plus | 92 Premium 1 2 Status display of the hands-free module. This status display is also visible in many other windows (see "Bluetooth / Phone" on page 20). Opens the OPTIONS window. There you can ► edit the system settings, see page 101. ► edit the Bluetooth settings, see page 100. ► view the text message (SMS) mailbox, see page 93. ► edit the Speed Call button, see page 99. 3 Opens the TRUSTED DEVICES window.
User’s manual NAVIGON 92 Plus | 92 Premium Phone Book: Opens the phone book of the active telephone (see "Calling a contact from the phone book" on page 95 and "Navigating to a contact from the phone book" on page 97). Recent Calls: Opens the recent calls of the active telephone (see "Calling most recently dialled, received or missed numbers" on page 95). 10.1 Bluetooth Connection To be able to use the hands-free module of the navigation device, it must be connected to at least one Bluetooth device.
User’s manual NAVIGON 92 Plus | 92 Premium ► If you want to set up a connection to a mobile phone, make sure that Bluetooth is activated on the mobile phone and that the Discoverable by Others and Others May Connect settings are activated. Note: The exact designation of these settings may vary from manufacturer to manufacturer. For details please refer to the manual issued for your mobile phone. ► If you want to set up a connection to a headset, make sure that it is switched on. 2.
User’s manual NAVIGON 92 Plus | 92 Premium ► 10.1.2 If the new device is a mobile phone, one of the two symbols will appear to the right of its name in green colour depending on whether it is connected as Phone 1 or as Phone 2. Pairing from the mobile phone Note: Please consult the mobile phone's manual if you are uncertain about how to carry out the following steps on the mobile phone. 1. Make sure that the Bluetooth function is activated on both the mobile phone and the navigation device.
User’s manual NAVIGON 92 Plus | 92 Premium Note: The exact designation of this setting may vary from manufacturer to manufacturer. For details please refer to the manual issued for your mobile phone. ► If you want to set up a connection to a headset, make sure that it is switched on. 1. Make sure that Bluetooth is activated on your navigation device.
User’s manual NAVIGON 92 Plus | 92 Premium If the telephone to which you want to connect the hands-free module is not in the list, you can start a search for Bluetooth devices (see "Searching for and pairing Bluetooth devices" on page 86). Connecting automatically Note: For automatic connection to be possible, the navigation device must be saved in the Bluetooth settings on your mobile phone as "authorised" or "authorised device" (the exact wording can vary from manufacturer to manufacturer).
User’s manual NAVIGON 92 Plus | 92 Premium 1. In the HANDSFREE MODULE window tap on (Trusted Devices). The TRUSTED DEVICES list opens. 2. Tap on (More) > Edit trusted devices. The EDIT TRUSTED DEVICES window opens. 3. Tap on the (Delete Device) button to the right of the device you want to delete. You will be requested to confirm deletion. 4. Tap on Yes. The device is deleted from the list. 5. Tap on OK. The TRUSTED DEVICES list appears again. 6. Tap on OK.
User’s manual NAVIGON 92 Plus | 92 Premium 3. Tap on OK. The HANDSFREE MODULE window opens again. Note: The number of phone book entries that can be imported from the mobile phone is limited to 1000. Note: It can take some time to import a phone book depending on its size. During the import you can move the Bluetooth application into the background in order e.g. to show the map during navigation. In the button bar tap on the corresponding button.
User’s manual NAVIGON 92 Plus | 92 Premium 10.1.7 Import recent calls For each paired mobile phone in the TRUSTED DEVICES list it is also possible to import its recent calls and save them together with the connection data. However, only the recent calls of the active mobile phone can be accessed. As soon as you activate a different phone or disconnect the Bluetooth connection, the recent calls will no longer be available on the hands-free module.
User’s manual NAVIGON 92 Plus | 92 Premium When you receive a text message (SMS), a signal tone will sound and the INCOMING TEXT MESSAGE window will open. The header line shows which connected telephone received the text message. The name and the number of the sender will be displayed if this information is available. (If the sender's number is not saved in the phone book, Unknown will be displayed instead of the name.) ► Tap on Read if you want to read the text message now. The TEXT window opens.
User’s manual NAVIGON 92 Plus | 92 Premium Note: If the selected Speed Call button has not been configured yet, it will be labelled with just three dots (…). If you tap on the symbol, the MODIFY PRESET window will open (see "Preset" on page 99). 10.4.3 Calling a contact from the phone book You can select numbers from the phone book of the active telephone. 1. In the HANDSFREE MODULE window activate the mobile phone which you want to use to make the call (see "Activating a mobile phone" on page 90). 2.
User’s manual NAVIGON 92 Plus | 92 Premium 3. Tap on the phone number you want to dial. Note: Only the recent calls of the active mobile phone can be accessed. As soon as you activate a different phone or disconnect the Bluetooth connection, the recent calls will no longer be available on the hands-free module. 10.4.
User’s manual NAVIGON 92 Plus | 92 Premium 2. Enter the desired numbers. 3. Tap on window. 10.5.4 (Back) in order to open the CALL IN PROGRESS Muting the microphone During the call, you can mute the microphone so that you can talk to someone without the interlocutor hearing. ► In the CALL IN PROGRESS window tap on Mute Microphone to switch off the microphone. The person on the other end of the line can no longer hear you. ► 10.5.5 Tap on Unmute Microphone to switch the microphone on again.
User’s manual NAVIGON 92 Plus | 92 Premium You can also select addresses from the phone book in the navigation software to act as destinations. For more details refer to the chapter "From the phone book" on page 36. 10.6.2 Opening the mailbox You can read text messages from the mailbox of the active telephone. Note: A maximum 15 text messages (SMS) can be imported from the mailbox of the mobile phone. 1. in the HANDSFREE MODULE window tap on (More) > Text Inbox. The TEXT INBOX list opens.
User’s manual NAVIGON 92 Plus | 92 Premium 10.7.1 Preset The hands-free module of the navigation device contains four Speed Call buttons that can be individually configured. The assignment of the Speed Call buttons is separately defined for each paired phone and saved with the phone's data. The Speed Call buttons for the active phone are available in each case. 1.
User’s manual NAVIGON 92 Plus | 92 Premium 10.7.2 Settings In the SETTINGS window you can configure the settings for the phone functions of the hands-free module. ► In the HANDSFREE MODULE window tap on Bluetooth Settings. The BLUETOOTH SETTINGS window opens. (More) > Volume of the Phone Call: The volume of the phone call can be controlled independently of the volume of the navigation application.
User’s manual NAVIGON 92 Plus | 92 Premium Note: The Discoverable by Others and Others May Connect settings are effective only when the Bluetooth function is activated. A Bluetooth connection can be initiated from the mobile phone only when Yes is selected for both settings. 11 Configuring the Navigation System The SETTINGS window is the starting point for customising the navigation system to match your personal preferences.
User’s manual NAVIGON 92 Plus | 92 Premium Some settings can adopt only the values Yes or No. These settings can be recognised by the checkbox alongside the setting. If the checkbox is activated If the checkbox is deactivated , the value is Yes. , the value is No. Some settings can adopt many different values. These settings can be recognised by the (List) button. The current value is visible. 1. Tap on (List). A list with all possible values opens. The currently valid value is marked. 2.
User’s manual NAVIGON 92 Plus | 92 Premium 12 Appendix 12.
User’s manual NAVIGON 92 Plus | 92 Premium 12.2 §1 NAVIGON Licensing Policy Scope of Regulations This Agreement regulates the relations between the user and NAVIGON AG, Schottmuellerstrasse 20 A, 20251 Hamburg, developer and proprietor of the exclusive utilisation rights to the NAVIGON software (“Software”) as specified in the order. The subject matter of this Agreement is copyright interests.
User’s manual NAVIGON 92 Plus | 92 Premium (2) Any kind of not explicitly authorized copying of the Software in its entirety or partially, any kind of not expressly authorized passing on of the Software and development of similar Software or segments of such Software or utilization of the contractual Software as master template shall in particular be deemed to be judicially and contractually prohibited.
User’s manual NAVIGON 92 Plus | 92 Premium §5 Reproduction Rights and Access Security (1) The user may reproduce the Software if the respective copying should be necessary for operation. Necessary reproduction shall be deemed to be the installation of the program from the original data carrier to the bulk memory of the hardware used as well as loading of the program into random access memory. (2) Furthermore, the user is permitted to make copies for back-up purposes.
User’s manual NAVIGON 92 Plus | 92 Premium §7 Third Party Software The Software contains third party software products which have been integrated into the contractual Software or supplied together with the contractual Software. NAVIGON fundamentally only awards such rights which are necessary for general use of the programs as components of the contractual Software and which NAVIGON is authorised to grant. No modification rights or further processing rights are incorporated therein.
User’s manual NAVIGON 92 Plus | 92 Premium (4) If the user should be a businessman within the meaning of the Commercial Code, legal entity under public law or special assets under public law, all disputes which may arise in connection with the accomplishment of these contractual regulations shall fall under the jurisdiction of Hamburg. 12.
User’s manual NAVIGON 92 Plus | 92 Premium It seems to me that the battery of my navigation device becomes flat relatively quickly when the device is not connected to an external power supply. Some settings can be configured so that energy consumption is minimised. 1. In the NAVIGATION window tap on Settings > Power and Screen. (More) > System 2. Set the values for Brightness Day and Brightness Night as low as possible. 3. Tap on OK. 4. Tap on (Back). The NAVIGATION window is now open again.
User’s manual NAVIGON 92 Plus | 92 Premium 14 Index B Block ................................................ 74 Bluetooth Activate ........................................ 90 Connect ....................................... 88 Pairing.......................................... 86 Bluetooth ........... see Handsfree Module Bluetooth Connection ....................... 86 Button bar..............................17, 52, 58 C Call Dial Number ................................. 94 Phone Book ....................
User’s manual NAVIGON 92 Plus | 92 Premium H M Handsfree Module Activate ........................................ 90 Bluetooth Connection ................... 86 Call .............................................. 94 Call in Progress ............................ 96 Connect ....................................... 88 Delete Device............................... 90 Dial Number ................................. 94 Enter Destination.......................... 96 Enter numerals .............................
User’s manual NAVIGON 92 Plus | 92 Premium New Route Route points ................................. 45 Starting Point ............................... 44 O Options ............................................. 18 P Pairing .............................................. 86 Parking Back to My Vehicle....................... 70 Last Destination ........................... 70 Parking Close to Destination ........ 69 Pedestrian mode .......................... 69 Skip current destination ................
User’s manual NAVIGON 92 Plus | 92 Premium Screenshots ..................................... 68 Service ............................................... 8 Settings Configuration.............................. 101 TMC ............................................. 83 Traffic Information ........................ 83 Volume......................................... 58 Settings Handsfree Module ...................... 100 Settings ..........................................
