User's Manual
Table Of Contents
- Safety and operational information
- Section 1 - General information
- Section 2 - Controls and keys
- Section 3 - Operating the radio
- Section 4 - Advanced setup
- 4-1 Waypoint
- 4-2 Backlight adjustment
- 4-3 Lamp timer
- 4-4 Buddy list (Manage your buddy list)
- 4-5 Contrast adjustment
- 4-6 GPS/DATA
- 4-6-1 Manual (Manually enter your position and UTC time)
- 4-6-2 Settings: LL display (Show or hide your position)
- 4-6-3 Settings: Time display (Show or hide the time)
- 4-6-4 Time offset (Local time)
- 4-6-5 Settings: Time format (12 or 24 hour clock)
- 4-6-6 Settings: COG/SOG (Course & speed display options)
- 4-6-7 GPS alert
- 4-6-8 Turn GPS ENABLE on/off
- 4-6-9 Set Magnetic Variation (MAG VAR)
- 4-7 Radio setup
- 4-7-1 Channel Bank selection (UIC)
- 4-7-2 Channel name editing (CH NAME)
- 4-7-3 Ring volume adjustment (RING VOLUME)
- 4-7-4 Beep volume adjustment (KEY BEEP)
- 4-7-5 Select unit (UNITS)
- 4-7-6 Set the Priority channel (WATCH MODE)
- 4-7-7 Weather alerts (WX ALERT)
- 4-7-8 Set NMEA output (NMEA OUT)
- 4-7-9 Favourite Channel Setup (FAV CH SETUP)
- 4-8 DSC setup
- 4-8-1 Enter or check your user MMSI (USER MMSI)
- 4-8-2 Maintain groups (GROUP SETUP)
- 4-8-3 Response to individual calls (INDIV REPLY)
- 4-8-4 Enable DSC functionality (DSC SELECT)
- 4-8-5 Response type to LL polling calls (LL REPLY)
- 4-8-6 Automatic Channel switching (AUTO SWITCH)
- 4-8-7 DSC Test Reply (TEST REPLY)
- 4-8-8 Set the inactivity timer (TIMEOUT)
- 4-9 ATIS SETUP (EU only)
- 4-10 Get Buddy
- 4-11 Track log
- 4-12 Erase track
- 4-13 Reset (Reset to factory defaults)
- Section 5 - Sending and Receiving DSC Calls
- 5-1 What is DSC?
- 5-2 DSC call types
- 5-3 Send an Individual call (INDIVIDUAL)
- 5-4 Reply to the Last Call (LAST CALL)
- 5-5 Send a Group call (GROUP)
- 5-6 Send an All Ships call (ALL SHIPS)
- 5-7 Reply to a call in your Call Log (CALL LOG)
- 5-8 Reply to a call in your Distress Log (DISTRESS LOG)
- 5-9 Request the LL position of a buddy (LL REQUEST)
- 5-10 Track your buddy request (TRACK BUDDY)
- 5-11 Make a DSC test call (DSC TEST)
- 5-12 View User MMSI and GPS information
- 5-14 Receiving DSC Calls
- 5-15 Receiving an All Ships Call (ALL SHIPS)
- 5-16 Receiving an Individual Call (INDIV)
- 5-17 Receiving a Group Call (GROUP)
- 5-18 Receiving a Geographic Area Call (GEOGRAPH)
- 5-19 Receiving a Polled Position Call (POSITION)
- Section 6 - Distress calls
- Section 7 - Installation Instructions
- Appendix A - Technical specifications
- Appendix B - Frequency charts
- Appendix C - EU inland waterway channels
Lowrance - Link-2 Installation and Operation Instructions 17Lowrance - Link-2 Installation and Operation Instructions16
3-6 Dual Watch operation
Dual watch monitors channel 16 while receiving another channel. To activate this, you
must:
1. Select the desired operating channel (e.g. CH88).
2. Push the SCAN key repeatedly until appears on screen.
3. To cancel dual watch, press SCAN (once) until disappears.
If a signal is received on channel 16, dual watch pauses on channel 16 until the signal
disappears.
To transmit on the selected channel during dual watch, press and hold PTT.
3-7 3CH operation (Favorite Channel)
You can instantly access the three most frequently used channels by 3CH mode, Three Fa-
vorite Channels. Press to toggle between your favorite channels. The , , or symbols
appear on the LCD to show which of your favorite channel is selected.
3-7-1 Add a favorite channel for the first time
1. Select the desired channel, then hold 3CH to store it. The CH1 symbol appears on
the screen.
2. Repeat the procedure to store two more favorite channels in the CH2 and CH3
locations.
3-7-2 Modify or delete favorite channel
If you try and add another favorite channel it will overwrite the existing CH3. But CH1 and
CH2 will remain unless you delete them.
To delete a favorite channel:
• Select that channel, then hold down 3CH until a dialog box appears to prompt the
deletion.
3-8 Scan Operation
Scanning is an eective way to locate signals quickly over a wide frequency range.
All Scan
All channels in the set are scanned sequentially, in repeated cycles (CH16 is checked every
1.5 seconds).
01
02
03
16
04
88
3CH Scan
Press and hold down the SCAN key in the 3CH mode, you will then enter a 3CH SCAN
mode. However, only the 3CH and CH16 will be scanned.
01
15
18
16
01
18
3-9 Navigation mode
Press and hold down NAV key, (US only), or just press the NAV key (EU only) to enter the
Navigation Mode. It will display: Bearing, Distance and cross track error from the last
selected waypoint.
If no WP is set, ‘NO ACTIVE ROUTE!!’ will appear to prompt you that no WP is selected.
During Nav Mode:
• PTT – return to normal mode and TX
• 16/9 – return to normal mode and go to 16/9
• NAV – return to normal mode
• GO – Reset the cross track error (XTE)
• SQL – Go to WP select Mode
• SQL – Go to Plotter Mode
• Other key – error beep.