BMA500M UNIVERSAL DIGITAL SUBFOOFER AMPLIFIER INSTALLATION/OWNER'S MANUAL IP66 Rated
BMA500M INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal (consult qualified technician for instructions). • Avoid installing the amplifier where it will be subject to high temperatures (such as from direct sunlight) or subject to dust, dirt or excessive vibration.
BMA500M INSTALLATION 1 2 2 + - 3 4 5 1. 12V+/Ground 2, Subwoofer out 3, Input Analog/Digital 4, Output Analog/Digital (Daisy Chain) 5. Bass Knob dash remote control Main Power Connections Connect +12V, GND wires accordingly. A suitable fuse MUST be installed on the +12V for protection of the vehicle's electrical system. SPEAKER OUT Connect using supplied din cables to your speaker, these outputs are mono and can be used with one or two speakers.
BMA500M INSTALLATION Connection Descriptions The information below should be used as a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the amplifier location. Use a grommet when running wires through the firewall or metal openings.
BMA500M INSTALLATION Audio Inputs DAISY CHAIN SETUP USING ANALOG SIGNAL WHEN USING ANALOG RCA FROM A RADIO, THE A2A CABLE (SOLD SEPARATELY) IS REQUIRED FOR DAISY CHAIN FUNCTION TO WORK.
BMA500M INSTALLATION EXAMPLE OF DAISY CHAIN CONFIGURATIONS FOR CAN-AM X3 VEHICLE *OPTIONAL ACCESSORIES ARE D2Y AND D2D CABLES (SOLD SEPARATELY) NA1BT/NA2BT/NA30C NA81MDVR(DIGITAL SOURCE UNITS) Acc(+12V) Ground(-) D2D CABLE 8 pin waterproof DIN connector D2D CABLE NS14A/27A/35A 2 pin waterproof DIN connector 10 Feet (10GA) 8 pin waterproof DIN connector 8 pin waterproof DIN connector Acc(+12V) Ground(-) 10 Feet (12GA) 4 inch(18ga) 8 pin waterproof DIN connector NT65AT BMA500M CONNECTING CABLE
BMA500M INSTALLATION Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. arrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
BMA500M INSTALLATION Specifications 8.5" x 3.8" x 1.6" 8.5" x 3.8" x 1.6" Power Output(@40hm) 250W x 1CH Power Output(@20hm) 500W x 1CH THD Signal to Noise Ratio(A-WTD) Frequency Response(-3dB) Input Impedance(Low Level) Sensitivity Range FUSE 0.1% ＞100dB 45Hz - 150kHz 20k Ohms 3V 40A x 1 Design and specifications subject to change without notice.
BMA500M INSTALLATION 9
Support Line: 1-562-946-7471 9AM-5PM PST Monday-Friday www.navatlas.com All rights reserved.
NT308W INSTALLATION/OWNER'S MANUAL 8" Tower Woofer
NT308W INSTALLATION Preparation/Installation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines or existing wiring. • If additional wiring is required, we recommend that you run all wires prior to mounting your speaker in place.
NT308W INSTALLATION Clamp Mounting The included clamping system is designed to support structures that utilize round tubing. Oval tubing and flat structures will not work with this clamp. The clamp can be used with tube diameters from 1.5” up to 2.75”. Separate bushing sets for all tube sizes at 1/8” increments are included. Refer to the table below to determine optimal configuration. Tube Diameter Tube Circumference Clamp Top Bushing Bottom Bushing 1.54 .71A 1.50 1.50 1.6255 .10A 1.63 1.
NT308W INSTALLATION Safety Cable The included safety cable is pre-installed on the unit. Mounting Bracket Rotation The mounting bracket rotates 360 degrees, allowing the speaker to rotate in any direction. Step 1 Loosen screw using the supplied tool. Step 2 Rotate speaker to desired direction, then tighten screw to lock in place. Step 3 Attach top bracket to bottom bracket using the four bolts. Make sure brackets are tightened all the way so there is no movement. 1. 4 2. 3.
NT308W INSTALLATION Connection Descriptions SPEAKER CONNECTION (PIGTAIL) • Tower woofers will connect to BMA500M using waterproof cables supplied with the amplifier, use caution when screwing/tightening waterproof connector as to not strip/ break thread or damage gasket.
NT308W INSTALLATION Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. arrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
NT308W INSTALLATION Specifications Woofer type Woofer surround Woofer size IMPP black (Injection molded polypropylene ) Rubber 8" RMS Power 200W Peak Power 400W Sensitivity Frequency response Impedance Enclosure type 85dB 45Hz - 500Hz 4 Ohms UV-resistant ABS plastic Design and specifications subject to change without notice.
Support Line: 1-562-946-7471 9AM-5PM PST Monday-Friday www.navatlas.com All rights reserved.
