Installation Sheet

1
2
3
4
5
INSTALLATION INSTRUCTIONS
3.5” BASKET STRAINER, DR320
1. Apply a small bead of
underside of strainer
body
flange (3).
2. Place strainer body (3)
into sink.
3. Place rubber seal (4) on
top of drain cup (5).
4. Place tightening screw
(2) into center of strainer
body (3) and secure.
5. Lubricate (1) with liquid
soap. Place strainer
basket (1) into strainer
body (3).
6. Attach drainpipe
(not
W W W .NA TIVETR A ILS. NET
Remove all excess silicone around the drain after the drain has been installed
100% silicone (non-water based)
to the
6
shown) to drain cup (5)
using nut (6)
1
2
3
4
5
INSTALLATION INSTRUCTIONS
3.5” BASKET STRAINER, DR320
1. Apply a small bead of
underside of strainer
body
flange (3).
2. Place strainer body (3)
into sink.
3. Place rubber seal (4) on
top of drain cup (5).
4. Place tightening screw
(2) into center of strainer
body (3) and secure.
5. Lubricate (1) with liquid
soap. Place strainer
basket (1) into strainer
body (3).
6. Attach drainpipe
(not
W W W .NA TIVETR A ILS. NET
Remove all excess silicone around the drain after the drain has been installed
100% silicone (non-water based)
to the
6
shown) to drain cup (5)
using nut (6)
1
2
3
4
5
INSTALLATION INSTRUCTIONS
3.5” BASKET STRAINER, DR320
1. Apply a small bead of
underside of strainer
body
flange (3).
2. Place strainer body (3)
into sink.
3. Place rubber seal (4) on
top of drain cup (5).
4. Place tightening screw
(2) into center of strainer
body (3) and secure.
5. Lubricate (1) with liquid
soap. Place strainer
basket (1) into strainer
body (3).
6. Attach drainpipe
(not
W W W .NA TIVETR A ILS. NET
Remove all excess silicone around the drain after the drain has been installed
100% silicone (non-water based)
to the
6
shown) to drain cup (5)
using nut (6)
1
2
3
4
5
INSTALLATION INSTRUCTIONS
3.5” BASKET STRAINER, DR320
1. Apply a small bead of
underside of strainer
body
flange (3).
2. Place strainer body (3)
into sink.
3. Place rubber seal (4) on
top of drain cup (5).
4. Place tightening screw
(2) into center of strainer
body (3) and secure.
5. Lubricate (1) with liquid
soap. Place strainer
basket (1) into strainer
body (3).
6. Attach drainpipe
(not
W W W .NA TIVETR A ILS. NET
Remove all excess silicone around the drain after the drain has been installed
100% silicone (non-water based)
to the
6
shown) to drain cup (5)
using nut (6)
1. Apply a small bead of 100% silicone (non-water based) to the underside of strainer body flange (3).
2. Place strainer body (3) into sink.
3. Place rubber seal (4) on top of drain cup (5).
4. Place tightening screw (2) into center of strainer body (3) and secure.
5. Lubricate (1) with liquid soap. Place stariner basket (1) into stariner body (3).
6. From working under the sink, slip the fiber gasket and the metal back up ring
(flat side up) that came with your waste disposer up and over the sink.
Note: You may need someone to help hold down flange sleeve until it
pops into place in the groove on the sleeve.
7. Hold the fiber gasket and metal back up ring in place with one hand and place the
mounting ring with the three bolt assembly onto the flange sleeve. Then push the
fiber gasket, metal back up ring and the mounting ring further up on the flange
sleeve and slide the snap ring onto the flange sleeve until it pops into place in the
groove on the sleeve.
8. Tighten the bolts on the three bolt mounting system until the whole mounting
system is seated evenly and tightly against the sink.