User Manual
Table Of Contents
- Title Page
- Disclaimer
- Contact
- Table of Contents
- 1 Introduction
- 2 Basic Concepts
- 3 Browser
- 4 Sound Slots
- 5 Creating Groups
- 6 Working with Patterns (Hardware)
- 6.1 Creating Patterns
- 6.1.1 Pattern Mode
- 6.1.2 Pad Mode
- 6.1.3 Pad Link
- 6.1.4 Releasing a Pad from a Pad Link Group
- 6.1.5 Recording the Pads
- 6.1.6 The Metronome
- 6.1.7 Using the Step Sequencer
- 6.1.8 Using Note Repeat
- 6.1.9 Using the Piano Roll/Keyboard
- 6.1.10 Recording Automation
- 6.1.11 Recording Automation in the Step Sequencer
- 6.1.12 Step Grid, Pattern Length Grid and Quantization
- 6.2 Editing Patterns
- 6.1 Creating Patterns
- 7 Working with Patterns (Software)
- 7.1 The Pattern Editor
- 7.2 Editing Patterns
- 7.2.1 Mouse Actions in the Pattern Editor
- 7.2.2 The Zoom Tool
- 7.2.3 Compare/Split
- 7.2.4 The Piano Roll / Keyboard
- 7.2.5 Recording and Editing Automation
- 7.2.6 Adding a Modulator
- 7.2.7 Step Grid, Pattern Length Grid and Quantization
- 7.2.8 Pad Link
- 7.2.9 Releasing a Pad from a Pad Link Group
- 7.2.10 Setting up a Pad as Master or Slave in a Pad Link Group
- 7.2.11 Rendering Audio from Patterns using Drag and Drop
- 7.2.12 Rendering MIDI from Patterns using Drag and Drop
- 8 The Effects Overview
- 9 Using FX
- 9.1 Applying Effects to a Sound
- 9.2 Applying Effects to a Group
- 9.3 Applying Effects to the Master
- 9.4 Bypassing Effects
- 9.5 Automating Effects and Sampler Parameters
- 9.6 Applying FX to an External Instrument
- 9.7 Recording FX Automation
- 9.8 Saving FX Presets
- 9.9 Creating a Send Effect
- 9.10 Creating a Multi Effect
- 10 Creating a Song using Scenes
- 11 Sampling and Sample Mapping
- 12 The Master Section
- 13 Exporting Audio
- 14 Appendix: Tips for playing Live
- Index
4.2.6 Page 6: Velocity Destination and Modwheel Destination
Sampler VELOCITY DESTINATION on the hardware.
Sampler Velocity Destination on the software.
Velocity Destination
Velocity Destination Controls
Start This is a built-in modulation source that allows you to modulate the sam-
ple Start parameter on page 2 based on the input velocity. Positive values
shift the sample start position later in time as you play harder, negative
values shift it closer to the beginning of the sample as you play harder.
Tip: a typical example for this parameter is setting it so that the initial at-
tack transient of a snare drum is heard only at high velocity values. This
makes it sound “snappier” when you play hard, and “mushier” or muted
when you play softly.
Decay This allows you to modulate the Decay parameter of the Amplitude Enve-
lope on page 2 by using Velocity.
Cutoff This allows you to modulate the Cutoff parameter of the Filters with filter
types LP, HP, BP (on page 3).
Volume This allows you to modulate volume, which is what Velocity normally is
used for.
Sound Slots
The Sampler Parameters in Module 1
MASCHINE - Manual - 71