FPT-1015 User Manual FPT-1015 User Manual December 2006 372051A-01
Support Worldwide Technical Support and Product Information ni.
Important Information Warranty The FPT-1015 is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty period. This warranty includes parts and labor.
Compliance Compliance with FCC/Canada Radio Frequency Interference Regulations Determining FCC Class The Federal Communications Commission (FCC) has rules to protect wireless communications from interference. The FCC places digital electronics into two classes. These classes are known as Class A (for use in industrial-commercial locations only) or Class B (for use in residential or commercial locations). All National Instruments (NI) products are FCC Class A products.
Conventions The following conventions are used in this manual: » The » symbol leads you through nested menu items and dialog box options to a final action. The sequence File»Page Setup»Options directs you to pull down the File menu, select the Page Setup item, and select Options from the last dialog box. This icon denotes a note, which alerts you to important information. This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss, or a system crash.
Contents Chapter 1 General Information Introduction....................................................................................................................1-1 Connectors .....................................................................................................................1-1 VGA Port (DB15)............................................................................................1-1 USB Type B Touchscreen Connector .............................................................
1 General Information This chapter includes an overview of the FPT-1015 human machine interface (HMI). Introduction The FPT-1015 is a 15 in. color TFT LCD flat panel monitor for industrial applications. With the optional touchscreen, this monitor is a user-friendly system control interface and can be easily transformed into a remote control system.
Chapter 1 General Information USB Type B Touchscreen Connector The FPT-1015 includes this connector and a touchscreen cable if a touchscreen is installed. You must connect it to the PC USB port. DC 12 V Power In This connector connects to the DC 12 V switching power supply. FPT-1015 User Manual 1-2 ni.
2 Mounting This chapter explains how to mount the FPT-1015. Important Safety Information Before setting up the FPT-1015, read these safety instructions carefully. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from excessive humidity.
Chapter 2 Mounting If one of the following situations arises, have service personnel check the equipment: • The power cord or plug is damaged. • Liquid has penetrated into the equipment. • The equipment has been exposed to moisture. • The equipment does not work well, or you cannot get it to work according to the user manual. • The equipment has been dropped and damaged. • The equipment has obvious signs of breakage.
Chapter 2 Mounting Wall Mounting The FPT-1015 wall mounting kit is optional. As shown in Figure 2-1, screw the hook and wall-mounted brackets to the wall and attach the FPT-1015 to the bracket. Hook Bracket Wall-Mounting Bracket Figure 2-1.
Chapter 2 Mounting Panel Mounting Refer to Figure 2-2 and follow these steps to install the FPT-1015 in a panel: 1. Place the panel-mounting brackets on the FPT-1015. 2. Fasten the panel-mounting brackets with the screws. 3. Insert the FPT-1015 in the panel. 4. Tighten the screws to fasten the FPT-1015 to the panel. Figure 2-2. Panel Mounting FPT-1015 User Manual 2-4 ni.
Chapter 2 Mounting Rack Mounting The rack mounting kit is optional. As shown in Figure 2-3, you can directly mount the FPT-1015 in a standard 19 in. rack and secure it with four screws. Figure 2-3.
Chapter 2 Mounting Desktop Stand Mounting The desktop stand kit is optional. As shown in Figure 2-4, attach the desktop stand bracket to the rear of the monitor with two screws. Figure 2-4. Desktop Stand Mounting Power Adapter Mounting Attach the power adapter bracket to the rear of the FPT-1015 monitor using four screws. Figure 2-5. Power Adapter Mounting FPT-1015 User Manual 2-6 ni.
A Specifications Physical Construction ........................................... Heavy-duty steel chassis Front Panel ............................................. Al-Mg, NEMA4/IP65 compliant Control ................................................... Onscreen display (OSD) control pad on front side Mounting................................................ Panel, wallmount, rackmount (with rackmount kit), desktop, or VESA arm Cutout dimension ................................... 373.5 × 297.5 mm (14.7 in.
Appendix A Specifications Dimensions 383 [15.07] 270.59 308.26 372.6 [10.65] [12.13] [14.66] 307 [12.08] 4.5 18.5 48.13 [0.17] [0.72] [1.89] 214.1 [8.42] 15 [0.59] 296.6 [11.67] 100 [3.93] 75 [2.95] 75 100 [2.95] [3.93] FPT-1015 User Manual A-2 ni.
Appendix A Specifications Touchscreen Type ....................................................... 8 wire, analog resistive Resolution .............................................. 1024 × 1024 Light transmission.................................. 75% (gouge hardness is greater than 4 H per ASTM D3363-92 for HCC01, HCG10, and HCG12) Controller ............................................... RS232 interface or USB 1.1 OS support.............................................. Windows 9x/NT/2000/XP/ CE 4.
Appendix A Specifications Sensor board ...........................................Chemical strengthened glass with 4 H hardness standard (test condition: ASTM D3363-92A) Ball drop test...........................................Able to bear a 225 g steel ball dropped from 660 mm elevation without breaking Accelerated aging ...................................100 h at 60 °C/95% relative humidity Thermal shock ........................................25 cycles (one cycle is 30 min.
Appendix A Specifications Environmental Maximum altitude .................................. 2,000 m Pollution Degree .................................... 2 Indoor use only Touchscreen Operating temperature range.................. –20 to 50 °C, 2 weeks at 50 °C/90% relative humidity Storage temperature high ....................... 70 °C, 240 h at ambient humidity Storage temperature low ........................ –40 °C, continuous at ambient humidity LCD Operating temperature............................
Appendix A Specifications Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control, and laboratory use: Note • EN 55024, CISPR 24 EMC requirements • EN 55022, CISPR 22 Emissions; Class A • EN 55011, CISPR 11 Emissions; Class A • CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A For EMC compliance, operate this device according to product documentation.
B Display Timing Mode and OSD Supported Input Timing Modes The FPT-1015 supports and automatically recognizes the frequencies listed in Table B-1. Table B-1. Supported Input Formats Vertical Frequencies Resolution 56 Hz 60 Hz 70 Hz 72 Hz 75 Hz 640 × 480 — Yes — Yes Yes 720 × 400 — — Yes — — 800 × 600 Yes Yes — Yes Yes 1024 × 768 — Yes Yes — Yes Even if you use the preset timing, you may need to adjust functions such as horizontal period, CLK-delay, and display position.
Appendix B Display Timing Mode and OSD Keypad Interface Table B-2 lists key functions. Table B-2. Key Functions Key Auto Sel Function Executes the autoadjustment process. Shows the OSD screen or selects an item to change its setting. Moves between items or increases/decreases item settings. Press both keys simultaneously to lock/unlock the current settings. Exit On/Off Closes the selected item or the entire OSD screen. Turns the FPT-1015 backlight on and off.
Appendix B Display Timing Mode and OSD OSD Function Each selected OSD function value is stored into LCD memory after an SEL signal input or timeout. The stored values are not affected if the power is off. However, the selected value is not available if a selected mode is changed or power is turned off before timeout. Table B-3 lists the OSD function menus. Table B-3.
C Touchscreen This appendix explains how to install and configure the FPT-1015 touchscreen. Introduction The FPT-1015 touchscreen uses advanced 8-wire resistive technology, providing more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments. Installing the Driver for Windows The touchscreen driver is on the driver CD included with the FPT-1015. To install the driver, locate the Windows Driver V4.1.1008 folder. Run setup.
Appendix C Touchscreen Standard Calibration When you click this button, arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After you touch the fifth red square, calibration is complete. To skip, press . Note To access the Advanced Calibration option, go to the Tools tab and select Advanced Calibration. Advanced Calibration Advanced calibration uses 4, 9, 16, or 25 points to effectively calibrate the linearity of aged touchscreens.
Appendix C Touchscreen Follow these steps to enable multiple displays: 1. In the Multiple Monitors tab, check the Multiple Monitor Support box. 2. Click Map Touch Screens to assign touch controllers to the displays. 3. When the mapping screen message appears, click OK. 4. Touch each screen as it displays Please touch this monitor. Following this sequence and touching each screen is called mapping the touchscreens. 5.
Appendix C Touchscreen Click on Touch—This option allows the mouse to have only a click function, and dragging is disabled. Beep Sound Mode Enable Beep Sound—This option turns the beep function on and off. Beep on Pen Down—In this mode, the beep occurs when the pen goes down. Beep on Pen Up—In this mode, the beep occurs when the pen goes up. Kind of Sound—This option modifies the type of sound the beep makes. Beep on Both—In this mode, the beep occurs when the pen goes down and up.
Appendix C Touchscreen Configuring the Rotate Function Follow these steps to configure the rotate function: Note 1. Install the rotation software package. 2. Choose the rotate function in the software. The calibration screen appears automatically. Touch the point, and rotation is mapped. The rotate function is disabled if you use monitor mapping. Tools Draw This option tests the touchscreen operation. The display shows touch location. Click Draw to start.
Appendix C Touchscreen PenMount Monitor Menu Icon The PenMount Monitor icon (pm) appears in the Windows menu bar when you turn on PenMount Monitor in PenMount USB Utilities. PenMount Monitor has the following functions: FPT-1015 User Manual Control Panel Brings up the PenMount Control Panel. Beep Turns the beep on or off. Right Button When you select this function, a mouse icon appears. Click this icon to switch between right and left button functions. Exit Exits the PenMount Monitor function.
Technical Support and Professional Services D Visit the following sections of the National Instruments Web site at ni.com for technical support and professional services: • Support—Online technical support resources at ni.
Index A E About function, C-5 advanced calibration, C-2 electromagnetic compatibility specifications, A-6 environmental specifications, A-5 LCD, A-5 touchscreen, A-5 examples (NI resources), D-1 C Calibrate function, C-1 calibration advanced, C-2 plot calibration data, C-2 standard, C-2 CE compliance specifications, A-6 cleaning, A-6 connectors, 1-1 DC 12 V power in, 1-2 USB type B touchscreen connector, 1-2 VGA port (DB15), 1-1 conventions used in the manual, v F FPT-1015, B-1 CE compliance specificat
Index K mounting, 2-1 desktop stand mounting, 2-6 panel mounting, 2-4 power adapter mounting, 2-6 rack mounting, 2-5 wall mounting, 2-3 OSD function, B-3 menus (table), B-3 PenMount Monitor menu icon, C-6 PenMount rotating functions, C-4 configuring, C-5 physical specifications, A-1 power adapter specifications, A-4 power indicator LED status, B-2 safety information, 2-1 specifications, A-5 specifications, A-1 supported input formats (table), B-1 supported input timing modes, B-1 touchscreen, C-1 configur
Index supported input formats (table), B-1 supported input timing modes, B-1 PenMount Monitor menu icon, C-6 PenMount rotating functions, C-4 configuring, C-5 physical specifications, A-1 plot calibration data, C-2 power adapter mounting, 2-6 specifications, A-4 power indicator LED status, B-2 programming examples (NI resources), D-1 T technical support, D-1 Tools function, C-5 touchscreen, C-1 configuring, C-1 environmental specifications, A-5 installing driver for Windows, C-1 introduction, C-1 PenMoun
