Let’s build the Reta Wall Light 0 30 SEMBL Y A S M I N UT E 3 SKU 15101 Scan me! Inspiration Digital Instructions Free Lifetime Warranty 22-1128
Ok, let’s get rolling This should be easy, just follow our instructions and you will be back to Netflix in no time. What’s included Description Qty 1 Fixture 1 2 Glass Shade 1 A M3.
Safety first, fun later Safe use of this product starts with you. Do not modify the structure of this product in any way. Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use. Our products have been tested to meet specific safety measures as they were originally intended to be sold.
The goods 1 A B C 2 D E F G H I IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools except where specified.
Pre-Installation • Read all instructions prior to beginning assembly. • To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. • Keep the receipt and these instructions for proof of purchase. • Suggested Bulb: A19 LED 60 Watt Equivalent | E26 Medium Base | Dimmable • Max. Wattage: 60W Plug-in option The following steps 1–11 are intended for wall mounted plug-in use only.
Step 2 Using the Round Mounting Plate (C) as a template, mark on your wall where you will need to drill the holes in order to mount the Fixture (1). C Step 3 Using a 1/4” drill bit and the reference marks from Step 2, drill 3 holes into the wall. Step 4 B Go ahead and tap the Wall Anchors (B) into place in the new holes you just drilled. You may be able to push them into place with your thumb.
Step 5 Using the M3.5*35mm Screws (A), mount the Round Mounting Plate (C) to the wall. B C B A B A A Step 6 1 Insert the Plastic Cap (G) to the hole on the underside of the Fixture’s (1) wall plate. G 1 Step 7 C Now attach the Fixture (1) to the Round Mounting Plate (C) on the wall using the Ball Nuts (D).
Step 8 Now you can go ahead and adjust the height of your Fixture (1) by loosening the knob and setting it to your desired height before re-tightening the knob to secure everything in place. 1 1 1 2 Be sure to keep a portion of the Fixture (1) tube sticking out of the bottom of the tube collar.
Step 9 1 You’re almost done! Now, remove the shade set screws. 1 Step 10 Set the Shade (2) in place, then secure using the set screws.
Step 11 You made it to the last step! We’re so proud of you. Now would be a great time to order a celebratory pizza (or two, you deserve it). For this last step, all that’s left to do is insert the bulb. We recommend one Type A19 bulb with a maximum wattage of 60 (not included). 120V 60Hz AC Only Troubleshooting Problem Possible Causes Solutions The bulb will not light. The bulb is burned out. Replace the light bulb. The power is off. Ensure the power supply is on. The circuit breaker is off.
Hardwired option The following steps 1–15 are intended for hardwire mounting to your existing electrical box. Skip back to page 5 for directions on how to mount this light on your wall as a plug-in light. Step 1 Let’s get this assembly going! Before you know it, you’ll be enjoying a nice book by your brand new wall light. E F First, secure the Mounting Bracket (F) to your existing electrical box using the M4*26mm Screws (E).
Step 2 Next, insert the Plastic Cord Eyelet (H) into the hole on the underside of the Fixture’s (1) wall plate. 1 H Step 3 Now for the fun part! Using wire cutters (not included) cut the cord right above the switch, then strip the ends of the wire using wire strippers (not included).
Step 4 Locate the plastic wire clamp on the backside of the Fixture (1), then, using a screwdriver, remove the screw to open the clamp up. 1 Open plastic clamp H Leave 6” of length from the cord knot to the cord end. Step 5 Feed cord through the Plastic Cord Eyelet (H), then into the open wire clamp on the backside of the Fixture (1).
Step 6 To set the cord in place, choose your desired exposed wire length between the fixture wall plate and the bottom of the Fixture (1), then, using the screwdriver, secure the plastic cord clamp closed. Step 7 First, wrap the Ground Wire from the Fixture (1) around the grounding screw on the Mounting Bracket (F) and then secure by tightening the screw. Electrical box Next, using a Wire Nut (I), join the Ground Wire from the Fixture (1) with the Ground Wire from your pre-installed electrical box.
Step 8 Use Wire Nuts (I) to connect the following wires together: I • Smooth Labeled Waire (from Fixture) to Black Wire (from Electrical Box) 1 • Textured Wire (from Fixture) to White Wire (from Electrical Box) I Black (Hot) Once complete, tuck excess wire into the electrical box.
Step 9 Secure the Fixture (1) to the Mounting Plate (F) on your pre-installed electrical box using the Ball Nuts (D). 1 D D To properly fasten the finial caps, thread in or out to adjust for proper threading length.
Step 10 Now, you can go ahead and adjust the height of your fixture by loosening the knob & setting it to you desired height before re-tightening the knob to secure everything in place. 1 2 Be sure to keep a portion of the Fixture (1) tube sticking out of the bottom of the tube collar.
Step 11 Remove the shade set screws. 1 1 Step 12 Set Shade (2) in place, then secure using the set screws.
Step 13 You made it to the last step! We’re so proud of you. Now would be a great time to order a celebratory pizza (or two, you deserve it). For this last step, all that’s left to do is insert the bulb. We recommend one Type A19 bulb with a maximum wattage of 60 (not included). 120V 60Hz AC Only Troubleshooting Problem Possible Causes Solutions The bulb will not light. The bulb is burned out. Replace the light bulb. The power is off. Ensure the power supply is on. The circuit breaker is off.
Questions? Don’t worry, we’ve got the answers What other light bulbs can fit in this light? Is this light compatible outside North America? The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit. Our lighting is only warranted in Canada and the United States.
No heartburn, when we handle the return Give us a call 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle. Our way Their way Give us a call Re-package item Replacement Schedule pick up You Track package Replacement You We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
We are only in business if you’re happy For starters, thanks for being you. Toll-free at 1-866-619-1004 Help@nathanjames.com NathanJames.com/help We do our best to ensure your product arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free. Warranty This product comes with a lifetime warranty from the date of purchase.
