Let’s build the Percy Pendant Light 5 35 SEMBL Y A S M I N UT E 3 SKU 12301 Scan me! Free Lifetime Warranty 23-1130
Ok, let’s get rolling What’s included Description Qty 1 Canopy 1 2 Fixture 1 3 Shade 2 A M4*26mm Screw 2 B Wire Nut 3 C Mounting Plate 1 D M4*15mm Screw 2 E M5*8mm Screw 2 This should be easy, just follow our instructions and you will be back to Netflix in no time.
Safety first, fun later Safe use of this product starts with you. Do not modify the structure of this product in any way. Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use. Our products have been tested to meet specific safety measures as they were originally intended to be sold.
The goods 1 A 2 B 3 C D IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools.
Pre-Installation • Read all instructions prior to beginning assembly. • To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. • Keep the receipt and these instructions for proof of purchase. • Suggested Bulb: A16 LED 60 Watt Equivalent | E26 Medium Base | Dimmable • Max. Wattage: 120W (60W per bulb) Step 1 D Yep, it’s as easy at it looks! Remove the M4*15mm Screws (D) from the Mounting Plate (C).
Step 3 Loosen the set screw towards the top of the fixture. This will allow you to set your desired cord length and shade height. Loosen set screw 2 Make sure both cords are the same length before securing the set screws. Thread excess cord length through the plastic cord stay. When desired length is achieved, pull to tighten.
Step 4 Guide the cords through the center of the Canopy (1). Then secure the Canopy (1) to the top of the Fixture (2) using the M5*8mm Screws (E).
Step 5 Allow cords to hang or rest freely, then secure the set screws to hold the cords at your desired length.
Step 6 Wrap the ground wire from the Canopy (1) around the grounding screw on the Mounting Plate (C). Then secure by tightening the screw. C 1 Note: Be sure that you are only making the connections to a 120V AC 60Hz circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
Step 7 Allow cords to hang or rest freely, then secure the set screws to hold the cords at your desired length.
Step 8 Use Wire Nuts (B) to connect the matching colored wires (White to White, Black to Black). Once complete, tuck the excess wire into the electrical box.
Step 9 Secure the Fixture (2) to the Mounting Plate (C) on your preinstalled electrical box using the M4*15mm Screws (D).
Step 10 Thread horizontal tubes into place. Step 11 Remove shade collar from the sockets by unthreading them.
Step 12 You’re almost done! Now install the Shades (3) by fitting them over the sockets, then thread the shade collars back into place.
Step 13 Install the light bulbs into place. And that’s it, time to enjoy your new light! Now would also be a good time for a celebratory pizza (or two, we’re not judging). Use 2 A16 LED 60 Watt Equivalent (not included). 120V 60Hz AC only. Troubleshooting Problem Possible Causes Solutions The bulb will not light. The bulb is burned out. Replace the light bulb. The power is off. Ensure the power supply is on. The circuit breaker is off. Ensure the circuit breaker is in the ON position.
Questions? Don’t worry, we’ve got the answers What other light bulbs can fit in this light? Is this light compatible outside North America? The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit. Our lighting is only warranted in Canada and the United States.
No heartburn, when we handle the return Give us a call 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle. Our way Their way Give us a call Re-package item Replacement Schedule pick up You Track package Replacement You We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
We are only in business if you’re happy For starters, thanks for being you. Toll-free at 1-866-619-1004 Help@nathanjames.com NathanJames.com/help We do our best to ensure your product arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free. Warranty This product comes with a lifetime warranty from the date of purchase.
