Let’s build the Nate Pendant Light 0 30 SEMBL Y A S M I N UT E 3 SKU 12102 Scan me! Inspiration Digital Instructions Free Lifetime Warranty 22-0830
Ok, let’s get rolling This should be easy, just follow our instructions and you will be back to Netflix in no time.
Safety first, fun later Safe use of this product starts with you. Do not modify the structure of this product in any way. Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use. Our products have been tested to meet specific safety measures as they were originally intended to be sold.
The goods A B C F D E IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools.
Pre-Installation • Read all instructions prior to beginning assembly. • To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. • Keep the receipt and these instructions for proof of purchase. • Use A19-type bulbs up to 60 watts or CFL or LED equivalent (not included). Step 1 Get your snack prepped and your workspace ready, it’s time to get started! Yep, it’s as easy as it looks. Remove the threaded collar ring from the Mounting Plate (C).
Step 2 F Now attach the Chain (F) to the top of the Fixture (A) and thread the chain loop until closed. F A Step 3 Now weave the cord through the Chain (F).
Step 4 Next, thread the cord and Chain (F) through the threaded collar ring and Ceiling Plate (B). B P.S. We aren’t judging you if you’ve already pulled out your snack. Ours was eaten by Step 2.
Step 5 You’re almost halfway there! We’re proud of you. Next, thread the wiring through the Mounting Plate (C), and hook the top of the Chain (F) onto the loop at the bottom of the Mounting Plate (C).
Step 6 Thread the top Chain (F) loop until closed.
Step 7 Electrical Box Time to get this light wired up! Install the Mounting Bracket (C) to your pre-installed electrical box using the M4*25mm Mounting Screws (D). C D B F A 10 D To properly fasten the Ceiling Plate (B) in place with the threaded collar ring, first adjust the height of the Mounting Bracket (C) accordingly by threading the center portion IN or OUT to adjust for proper length.
Step 8 Wrap the ground wire around the grounding screw on the Mounting Bracket (C) and secure in place by tightening the grounding screw. Note: Be sure that you are only making the connections to a 120V AC 60Hz circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
Step 9 Almost done! Now use the Wire Nuts (E) to connect all the wires. Locate and retrieve the supply wires from the junction box. a. Connect the black wire from the fixture to the NEUTRAL wire in the junction box (typically white). b. Connect the black wire with “L” label from the fixture to the HOT wire in the junction box (typically black). c. Connect the bare copper wire to the GROUND wire in the junction box (typically bare). Once complete, tuck the excess wire into the electrical box.
Step 10 Secure the Ceiling Plate (B) to the Mounting Bracket (C) by tightening the threaded collar ring around the threaded portion of the Mounting Bracket (C). This may require some minor adjustments to the length of the threaded portion of the Mounting Bracket (C) (refer to tip from Step 7).
Step 11 You made it to the last step! You’ve been doing such an impressive job that we’ve decided to make this step the easiest. Simply screw in the light bulb, and then you’re done! We recommend using Type A19 bulbs (not included) with a maximum wattage of 60W. 120V 60Hz AC Only Troubleshooting Problem Possible Causes Solutions The bulb will not light. The bulb is burned out. Replace the light bulb. The power is off. Ensure the power supply is on. The circuit breaker is off.
Questions? Don’t worry, we’ve got the answers What other light bulbs can fit in this light? Is this light compatible outside North America? The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit. Our lighting is only warranted in Canada and the United States.
No heartburn, when we handle the return Give us a call 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle. Our way Their way Give us a call Re-package item Replacement Schedule pick up You Track package Replacement You We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
We are only in business if you’re happy For starters, thanks for being you. Toll-free at 1-866-619-1004 Help@nathanjames.com NathanJames.com/help We do our best to ensure your light fixture arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free. Warranty This product comes with a lifetime warranty from the date of purchase.
