ARMED READY ü SYSTEM Using Your XP-400 Security System ZONE 1 ZONE 2 ZONE 3 ZONE 4 NAPCO Oi220a.
Oi220a.
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use.
Introduction Table of Contents Keypad Controls and Indicators ................................ Arming your System (When Leaving) ....................... Bypassing Zones ..................................................... Protecting Yourself While Home ............................... Emergency Keys ....................................................... Disarming the System ............................................... Silencing an Alarm.....................................................
Keypad Controls and Indicators * Key Used to enable special functions and options. Press *and then the corresponding Special Function number Option (See Special Functions, Page 10) Numerical Keys 1-9, 0. Used to enter User Codes, Zone numbers, etc. ARMED READY Armed Light will light when system is Armed, and will flash when system is in Alarm Ready Light will light when all zones are secure and system is ready to be Armed. üSYSTEM Bypass Key Used to bypass zones.
Arming Your System Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing zones below. 2 Enter your user code. The Green Ready light will go out, the Red Armed light will light. • If you make a mistake entering your code, press B and re-enter the code.
Arming Your System Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. ARMED READY SYSTEM • 2 Enter your user code. The Green Ready light will go out, and the red Armed light will light.
Emergency Conditions Emergency Buttons f f Yes Auxiliary Emergency Enabled? G Yes No Police Emergency Enabled? No Ambush Alarm Enabled? Yes FG The two sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time.
Disarming Your System / Silencing an Alarm Disarming Your System when Returning ARMED READY 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press the B key and re-enter the code.
Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing a followed by 0. This will allow the easy arming of the system by someone who is not a regular system user. a0 Easy Exit (when system is armed) This function (if programmed) allows an occupant to leave the premises without disarming the system.
Programming User Codes Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode ARMED READY SYSTEM Press A followed by 8 and then enter the User 1 code. The Armed, Status and ü System Lights will flash, and the keypad will beep 4 times.
ü System Troubles The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow ü SYSTEM light and beeping the keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used.
ü Keypad Beeps or ARMED System Trouble Condition System Troubles ü SYSTEM Flashes Zone light ON Action 2 Beeps 1 Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing company for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver. Call installing company for service. 2 Beeps 4 Wireless Receiver Jam A problem has been detected with a wireless receiver. Call installing company for service.
Glossary Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your system has the Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code Arming / Disarming - Turning the system on or off by entering your user code at the keypad.
Notes 15 Oi220a.
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
