ZG-7600H-P User Manual ZG-7600H-P User Manual Page I
ZG-7600H-P User Manual Copyright There is no any clear or implicit assurance in the user's manual of our company, including the assurance of selling or installing for the special purpose. There are rival's volumes to carry on the power to alter or revise in our company, if alter and forgive me for not issuing a separate notice. You can’t duplicate any content of this manual by the written permission of our company. About the manual The purpose to use this manual is for install the wireless Access Point.
ZG-7600H-P User Manual RF exposure warning · This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
ZG-7600H-P User Manual Content Chapter 1 Introduction ............................................................................................... 1 Introduction to Product................................................................................................1 LED and Port Definition .............................................................................................1 Chapter 2 Hardware Installation ...............................................................................
ZG-7600H-P User Manual Management Control.................................................................................................25 Reboot AP .................................................................................................................25 Remote Management.................................................................................................26 View Log ...................................................................................................................
ZG-7600H-P User Manual Content of Figure Figure 1 Product Panel ..............................................................................................................1 Figure 2 login ............................................................................................................................6 Figure 3 Status Page ..................................................................................................................6 Figure 4 System Setup....................................
ZG-7600H-P User Manual Content of Table Diagram 1 LED and Port Definition .........................................................................................1 Diagram 2 Default Settings .......................................................................................................5 Diagram 3 Super-G Reference Throughput.............................................................................19 Diagram 4 Turbo-G Reference Throughput .........................................................
ZG-7600H-P User Manual Chapter 1 Introduction Introduction to Product ZG-7600H-P, a 4-in-1 SMB High Power WLAN Access Point, support PoE, 200mW Output Power, can be operated in one of the following 4 modes, except general access point, also include AP client, repeater and point to point bridge. The 802.11g-compatible device delivers a 54Mbps high-speed, reliable and easy-to-use wireless connection throughout your home or small office at an affordable price.
ZG-7600H-P User Manual WLAN Blinking : Data TX/RX through wireless access point Port Description POWER Reserved (DC 12v/0.
ZG-7600H-P User Manual Chapter 2 Hardware Installation System Requirements 1. A computer has a 10/100Base-TX Ethernet that is connected to the same IP segment as the AP. 2. The computer has one Web browser, such as Microsoft Internet Explorer 6.0.
ZG-7600H-P User Manual Chapter 3 Safely Use Your Device Safely Use in Installation 1. Please do not put Access Point near these places: electric power line, electric light, electricity or any places nearby strong electric power, otherwise it may make damage to Access Point.
ZG-7600H-P User Manual Chapter 4 Basic Configuration Default Settings Diagram 2 Default Settings Options Default Value User Name admin password password Device Name APxxxxxx(xxxxxx indicate the last 6 MAC address of AP) Country/Region China IP Address IP Type: Fixed IP Address :192.168.0.228 Mask :255.255.255.0 Gateway:0.0.0.0 Operating Mode AP Mode Wireless Mode Auto(11g/11b) Channel/Frequency 6/2.
ZG-7600H-P User Manual Using the Web Management The Web Management provides you with a user-friendly graphical user interface. The Access Point allows you via web browser (MS Internet Explorer 6.0) to monitor and configure the device. 1. Run Web Explorer, Enter default IP Address: http://192.168.0.228 in the Address field. And press Enter. Figure 2 login 2. Enter default Password (password), Click Login. The home page will show up.
ZG-7600H-P User Manual System Setup Figure 4 System Setup Device Name This is the NetBIOS name of Access Point; you may modify the default name with a unique name up to 15 characters long including numbers from 0 to 9, letters (A-Z; a-z) and digraphs (-), the name supports WINS so you can ping Access Point using ping Access Point Name or use web browser to open web utility by inputting Access Point Name in the IE address. Country/Region Select your country or region from the drop-down list.
ZG-7600H-P User Manual Wireless Settings Figure 5 Wireless Settings Operating Mode AP: This mode is used to build cover with wireless network which allowing wireless device connection. Bridge: This mode is used to build point to point and point to multi point network which allowing other wireless bridge connection by wireless. AP + Reporter: This mode allows both cover with wireless network and wireless bridge connection by wireless. AP Client: This mode is used to connect with an AP.
ZG-7600H-P User Manual 802.11g Only: Setup 802.11g network and only 802.11g STA could connect up it. 802.11b Only: Setup 802.11b network and only 802.11g/b STA could connect up it. Auto(11g and 11b):Setup 802.11g/b network and only 802.11g/b STA could connect up it. Beacon Interval Specifies the interval time (20 ~1000ms) for each beacon transmission. DTIM Interval The Delivery Traffic Indication Message, Specifies the data beacon rate between 1 and 255.
ZG-7600H-P User Manual Turbo-G mode provides higher speed transmissions than Super-G mode. RTS/CTS Threshold Request to Send Threshold. Its value is from 0 to 2346 bytes, RTS is designed to solve Network collision. It will make signals lose if two stations send data to AP at the same time. When the transmitted data size is larger than RTS threshold, the RTS mechanism will be active.
ZG-7600H-P User Manual Chapter 5 Advanced Configuration VAP(Virtual AP) Setup One device could be used to eight devices. So you could easy setup your network and manage different users. And the eight VAP could set different security to protect your network.
ZG-7600H-P User Manual Figure 7 Security Set Security Profile Name You could use a friendly name to manage different VAP. SSID The SSID is a unique ID used by Access Points and Stations to identify a wireless LAN. Wireless clients associating to any Access Point must have the same SSID. The default ESSID is “Wireless”. The ESSID can up to 32 characters Broadcast SSID If you hide the SSID, then the device cannot be seen when a wireless client scans for local APs.
ZG-7600H-P User Manual Choose the following type. WEP 1. Open System: wireless device does not any authentication and can be connected with Access point. But the message between wireless device and Access point also use encryption through the following type “authentication type”. 2. Shared Key: If Shared Key is selected, you need to enabled WEP and enter at least one shared key. “Shared Key” authentication type is working cooperate with “data encryption type”.
ZG-7600H-P User Manual You must configure RADIUS Server Settings with either Legacy 802.1x, WPA or WPA2 option. Authentication Server This configuration is required for authentication using RADIUS. IP Address, Port No. and Shared Secret is required for communication with RADIUS Server. IP Address: IP address of the RADIUS Server. The default is 0.0.0.0 Port Number: Port number of the RADIUS Server. The default is 1812.
ZG-7600H-P User Manual Figure 8 Bridge Mode Setup In Security Profile page, you could select WDS_Profile to edit. And set the encryption between the devices.
ZG-7600H-P User Manual Figure 9 Security Set in Bridge Mode AP Client Mode Setup In Wireless Settings page, you could set operation mode to AP Client mode. And you should input the SSID to connect with AP.
ZG-7600H-P User Manual Figure 10 AP Client Mode Setup In Security Profile page, you could select STA_Profile to edit. And set the encryption between the devices. Figure 11 Security Set in AP Client Mode 802.1Q VLAN Setup In AP mode, you could enable 802.1Q VLAN to manage users.
ZG-7600H-P User Manual Figure 12 802.1Q VLAN Management VLAN ID Management VLAN ID is used to manage device and monitor the network. Profile VLAN ID Profile VLAN ID is used to manage VLAN. You could set ID 1~4049. MAC Filter The optional MAC Filter window lets you block the network access privilege of the specified stations through the Access Point. This provides an additional layer of security. There are two kinds of MAC Filter.
ZG-7600H-P User Manual Figure 13 MAC Filter You could enable MAC Filter and input the allowed or denied STA’s MAC. Throughput Accelerate There are two ways to accelerate throughput in our Access Points: Super-G and Turbo-G. Super-G Application If open Super-G Function, it can obviously improve the throughput of wireless network. The following table gives you a reference.
ZG-7600H-P User Manual Turbo-G The following table gives you a reference. Diagram 4 Turbo-G Reference Throughput Mode Turbo-G OFF Turbo-G ON AP mode 20Mbps 30Mbps AP and client support Turbo-G.
ZG-7600H-P User Manual Chapter 6 Management View Device’s Status Figure 14 Status The Status page displays current settings and statistics of your Access Point that is Read-only, and any change of settings must be made on other pages. View Association List Figure 15 Association List In Status page, click View Association List to show the wireless stations that are currently associated to the device.
ZG-7600H-P User Manual View Statistics Figure 16 Statistics Info In Status page, click View Statistics to see performance statistics such as number of packets sent and number of packets received. Change Password Figure 17 Change Password In Password Setup page, you could change the password for accessing the Settings pages.
ZG-7600H-P User Manual Firmware Upload In F/W Upload page, you could upgrade Access Point software. Figure 18 Firmware Upload 1. Open Upgrade Firmware page 2. Click browser button and select the firmware file in local hard disk. 3. Click Upload button. 4. After upgrade, login again and check the software version.
ZG-7600H-P User Manual Figure 19 Configuration File Click button to save backup file to hard disk. Click Browser button to locate the backup file you want to retrieve and click retrieve button, then the AP will restart. Do not try to turn off the Access Point, shutdown the computer or do anything else to the Access Point until the Access Point finishes restarting! Restore to Factory There are two kinds way to restore Access Point to factory.
ZG-7600H-P User Manual Management Control Management Control function lets you allow or deny the specified IP address to manage the device. Figure 20 Management Control Reboot AP Figure 21 Reboot AP You may select Yes on Reboot page and then click on Apply button to reboot the access point.
ZG-7600H-P User Manual Remote Management Figure 22 Remote Management SNMP Settings. IP Address to Receive Traps: You can find the unusual log on the Trap Server. Public Community Name: Set the Read Community; Private Community Name: Set the write Community; View Log You could check system log to view the operations between AP and STA.
ZG-7600H-P User Manual Chapter 7 Typical Applications Wireless Coverage In the AP mode, it can be set as wireless coverage spot. Figure 24 Wireless Coverage Application STA-A/B/C connect AP by SSID, and then they can access PC in Ethernet and internet. Do steps as following: 1. Set Operation Mode as AP mode in Wireless Settings page. If you want to be compatibility with 802.11b device, you should set Wireless Mode as Auto. 2. Open Security Profile page, you could enable profile 1~8 and 802.1Q VLAN 3.
ZG-7600H-P User Manual Figure 25 Point to Multi-Point Application Access Points builds connection by WDS (Wireless Distribution System) mode. The main setting is remote MAC address. The following steps are the way. 1. After power on two Access Points, use two computers to connect each of them by network cable. 2. Set Operation Mode as Bridge mode in Wireless Settings page, add MAC address of remote wireless bridge and set the real Wireless Space. 3. Now the two Access Points have normally worked.
ZG-7600H-P User Manual Chapter 8 Troubleshooting How to know the MAC address of the Access Point? • The MAC address is written in a label which is in the bottom of Access Point. • From the General page of WEB configuration, you also can get the MAC address of AP. Why STA can’t connect with AP? The process of STA connects with AP need probe request, auth, connect steps, so you could do: • STA can’t detect AP. So you could check the domain or country, to keep AP and STA use the same one.
ZG-7600H-P User Manual • Check the “Operating Mode” whether is “Bridge Mode”. • Check the “remote MAC address” whether is right. • Check the “Country/Region” whether is same. • Check the “Channel/Frequency” whether is same. • Check the “Data Encryption” and “Key” whether is same.
ZG-7600H-P User Manual Appendix A. Specifications Diagram 5 Device Specification ZG-7600H-P IEEE 802.11g 54Mbps Wireless Access Point Appendix A.
ZG-7600H-P User Manual Designing to IEEE 802.11g WLAN network that works at 2.4 GHz Direct Sequence Spread Spectrum (DSSS), ZDC ZG-7600H-P, a 4-in-1 WLAN Access Point, can be operated in one of the following 4 modes, except general access point, also include AP client, repeater and point to point bridge. With data rate of up to 108Mbps, ZG-7600H-P is capable of delivering large files and streams MPEG video. It is ideal WLAN application in home or small office environment. With latest WPA2 and 802.
ZG-7600H-P User Manual Standard IEEE 802.11g IEEE 802.11b IEEE 802.3 and IEEE 802.3u IEEE 802.3af POE Yes, IEEE802.3af Ethernet Data Rate Auto / 10M / 100M Rate Select SuperG/11g: 108 /54 /48 /36 /24 /18 /12 /9 /6 Mbps Auto 11b: 11 /5.5 /2 /1 Mbps Auto Data modulation type OFDM/BPSK/QPSK/CCK/PBCC/DQPSK/DBPSK Output Power (from MiniPCI) 11g:21+/-1dBm @54Mbps 11b:23+/-1dBm @11Mbps Sensitivity 11g: 11b: 54M : ≤-72dBm 11M : ≤-87dBm 48M : ≤-75dBm 5.
ZG-7600H-P User Manual WDS Mode AP + Repeater AP Client Mode Yes, Support Multiple Client DHCP DHCP Client Super G Yes Turbo G Yes QoS (WMM) Yes Multi-BSSID Yes VLAN Yes Output power configurable Yes (4 levels) System log Yes STA list Yes Radio ON/OFF Yes Load Balance of Multi AP Yes Security WEP Encryption 64/128/152-bits 802.
ZG-7600H-P User Manual LED Power / LAN / WLAN Power Supply POE Physical Dimension 142mm(L)*134mm(W)*46mm(H) Weight Approx: 0.9Kg Environment Operating Temperature 0~55℃ Storage Temperature -30~60℃ Humidity 20~95﹪ Appendix A.
ZG-7600H-P User Manual Appendix B. ASCII Character Chart You can dispose hexadecimal number system counting or ACSII one yard of keys encrypted as WEP. Hexadecimal number system is made up by 0-9 and A-F (letter does not distinguish capital and small letter); ACSII yard is by 0-9 figures, A-F, a-f (letter distinguishes capital and small letter), and the punctuation mark makes up. Each ACSII yard can is it says to count by one hexadecimal number system of two.
ZG-7600H-P User Manual Appendix C. Country/Region and Channel Diagram 7 Country/Region frequency list Country/Region 5.8G Frequency(MHz) 2.
ZG-7600H-P User Manual Diagram 8 Channel/Frequency List 5.8G Channel Frequency(MHz) 2.