ZDC ZA-5000-D User's Manual V2.3.2 ZA-5000-D User’s Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.2 Copyright There is no any clear or implicit assurance in the user's manual of our company, including the assurance of selling or installing for the special purpose. There are rival's volumes to carry on the power to alter or revise in our company, if alter and forgive me for not issuing a separate notice. You can’t duplicate any content of this manual by the written permission of our company.
ZDC ZA-5000-D User's Manual V2.3.2 FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ZDC ZA-5000-D User's Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.2 Content Chapter 1 Introduction................................................................................................1 Introduction.................................................................................................................1 Appearance of Product................................................................................................1 Features and Benefits ................................................................................
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 5 Management .............................................................................................35 View the General Information...................................................................................35 View the STA List .....................................................................................................35 View the Device’s Link Status ..................................................................................
ZDC ZA-5000-D User's Manual V2.3.2 Figure 11 Wireless2 Settings...................................................................................................17 Figure 12 Wireless Repeater Connection ................................................................................20 Figure 13 Wireless1 WDS Settings.........................................................................................21 Figure 14 Wireless2 WDS Settings....................................................................
ZDC ZA-5000-D User's Manual V2.3.2 Content of Table Diagram 1 Default Settings.....................................................................................................10 Diagram 2 Country/Region frequency list (5GHz frequency band）.....................................13 Diagram 3 Country/Region frequency list (2.4GHz frequency band）..................................14 Diagram 4 Channel/Frequency List（5GHz）.......................................................................
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 1 Introduction Introduction The next-generation Broadband Wireless Access device－ZA-5000-D Dual-RF Outdoor Wireless Access Point, Simultaneously works as 5GHz Bridge and 2.4GHz Access Point. The new features and benefits are: support POE (power over Ethernet); support testlink, use this utility, you can place the antenna in the best place. Surface packing is full block out and with waterproof function. The Access Point provides powerful features.
ZDC ZA-5000-D User's Manual V2.3.2 Wireless module 1 works as 5GHz Wireless module 2 works 5GHz/2.
ZDC ZA-5000-D User's Manual V2.3.2 Figure 3 Point to Multi Point Wireless Repeater Application condition: This solution is used for builds wireless repeater bridge between two places which there are long distance and can not be visual. Figure 4 Wireless Repeater Access Point Application condition: This solution is used for mobile office places.
ZDC ZA-5000-D User's Manual V2.3.2 Figure 5 Access Point Representative Application The Access Point offers a fast, reliable, cost-effective solution for wireless client access to the network in applications like these: Remote Access to Corporate Network Information E-mail, file transfer and terminal emulation. Difficult-to-Wire Environments Historical or old buildings, asbestos installations, and open area where wiring is difficult to deploy.
ZDC ZA-5000-D User's Manual V2.3.2 store or office campus. SOHO (Small Office and Home Office) Users SOHO users need easy and quick installation of a small computer network. High Security Connection The secure wireless network can be installed quickly and provide flexibility.
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 2 Hardware Installation System Requirement Two PCs with RJ-45 connector NIC supporting the transfer rate of 10/100Mbps data. The IP address of NIC should be the same subnet with the AP, the default IP address of AP is 192.168.0.228. Microsoft Internet Explorer 6 updated with Service Pack 1 or the newer patch Q323308.
ZDC ZA-5000-D User's Manual V2.3.2 4. Attach STP cable to the RJ-45 connector on the Access Point. Then connect another end of the RJ-45 cable to a hub or a terminal. 5. Plug water-joint into the Access Point and tighten it. 6. Attach the external antenna to Access Point.
ZDC ZA-5000-D User's Manual V2.3.2 7. Connect the Access Point to the ground via ground connection which is beside the RJ-45 port. Thus all, the hardware installation is completed. Notice: There is a plastic film covering the build-in antenna. Please tear this film while using ZA-5000-D. Warning： Please confirm ground connection of the Access Point. Please confirm ground connection of the STP cable, and traverse an EMI suppression ferrite ring core.
ZDC ZA-5000-D User's Manual V2.3.2 Warning： Please do not put Access Point near these places: electric power line, electric light, electricity or any places nearby strong electric power, otherwise it may make damage to Access Point. The inner Antenna Lightning Protection is in base level. You should add advanced Antenna Note:Lightning Protection if condition possible.
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 3 Basic configuration Default Settings Diagram 1 Default Settings Options Default Value Wireless module 1 Wireless module 2 User Name admin password password Access Point Name APxxxxxx（xxxxxx indicate the last 6 MAC address of AP） Country/Region China IP Address IP Type: STATIC IP Address :192.168.0.228 Mask ：255.255.255.0 Gateway：0.0.0.0 Bridge Mode Bridge Bridge Operating Mode 802.11a 802.11a Channel/Frequency 149/5.745GHz 149/5.
ZDC ZA-5000-D User's Manual V2.3.2 SNMP SNMP：Enable Trap Server：192.168.0.254 Read Community：public Write Community：private Using the Web Management The Web Management provides you with a user-friendly graphical user interface. The Access Point allows you via web browser (MS Internet Explorer 6.0) to monitor and configure the device. 1. Run Web Explorer, Enter default IP Address: http://192.168.0.228 in the Address field.
ZDC ZA-5000-D User's Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.2 This is the NetBIOS name of Access Point; you may modify the default name with a unique name up to 15 characters long including numbers from 0 to 9, letters (A-Z; a-z) and digraphs (-), the name supports WINS so you can ping Access Point using “ping Access Point Name” or use web browser to open web utility by inputting Access Point Name in the IE address. Notice: The default Access Point Name is: APxxxxxx (xxxxxx represents the last 6 digits of MAC address.
ZDC ZA-5000-D User's Manual V2.3.2 Netherlands 36-64,100-140 New Zealand 36-64,149-165 Norway 36-64,100-140 Portugal 36-64,100-140 Singapore 36-64,149-165 Spain 36-64,100-140 Sweden 36-64,100-140 Switzerland 36-64 Taiwan 56-64,149-161 United Kingdom 36-64,100-140 United States 36-48,149-165 36-48 indoor use Diagram 3 Country/Region frequency list (2.
ZDC ZA-5000-D User's Manual V2.3.2 There three type in Bridge mode: Static IP: You should manually configure IP address, subnet mask, gateway. The Access Point will automatically calculate the subnet mask based on the assigned IP address. Otherwise, you can use 255.255.255.0 as the subnet mask. DHCP Client: AP can get IP settings from DHCP Server.
ZDC ZA-5000-D User's Manual V2.3.2 z 48 5240 52 5260 56 5280 60 5300 64 5320 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 Data Rate The available transmit data rate of the wireless network. The AP will choose the highest data rate to transmit data in Best mode. You also can choose lower data rate in order to transmit data in longer distance.
ZDC ZA-5000-D User's Manual V2.3.2 always. z Fragmentation Threshold This is the maximum packet size used for fragmentation and can only be set as even number. Packets larger than the size programmed in this field will be fragmented. The little packet data can reduce loses and raises the quality of transmission. Notice: The Fragment Threshold value should be larger than the RTS Threshold value or the RTS Threshold is zero, otherwise the RTS function will not work.
ZDC ZA-5000-D User's Manual V2.3.2 Select the channel that you plan to use. Diagram 5 Channel/Frequency List（5GHz） Channel Centre Frequency（MHz） 34 5170 36 5180 38 5190 40 5200 42 5210 44 5220 46 5230 48 5240 52 5260 56 5280 60 5300 64 5320 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 Diagram 6 Channel/Frequency List（2.
ZDC ZA-5000-D User's Manual V2.3.2 z 8 2447 9 2452 10 2457 11 2462 12 2467 13 2472 14 2484 Data Rate The available transmit data rate of the wireless network. The AP will choose the highest data rate to transmit data in Best mode. You also can choose lower data rate in order to transmit data in longer distance. z Output Power Adjust thepower transmit level. power of the Access Point. The more the Output Power the more area of Fixed the wireless signal can reach. Its default value is Full.
ZDC ZA-5000-D User's Manual V2.3.2 Outdoor Wireless Repeater Application Here we will introduce you how to build such network quickly We suggest you should first builds networks between two wireless bridges indoor and the connection is normal then take them outdoor. Access Points builds connection by WDS (Wireless Distribution System) mode. The main setting is remote MAC address. The following steps are the way. Step from 1 to 5 is taken indoor; step 6 should take Access Points outdoor. 1.
ZDC ZA-5000-D User's Manual V2.3.2 Figure 13 Wireless1 WDS Settings Figure 14 Wireless2 WDS Settings Notice: You should set the two Access Points different IP addresses in order to expediently manage them. 3. After above configuration, to confirm the right connection of wireless network, you can use “ping” program. At the local notebook computer (192.168.0.1), ping 192.168.0.2, ping 192.168.0.3. If the device does not work or the ping is timed out, please take a reference to chapter “Troubleshooting”.
ZDC ZA-5000-D User's Manual V2.3.2 Settings” page, input the real space between Bridges. Then open “Link Test” page, check those settings whether is right. If right. 6 6 Figure 15 Link Test Notice: For the accuracy of test result, you should make sure that the Link Test settings are right. Click start button to begin test. The result will show bellow.
ZDC ZA-5000-D User's Manual V2.3.2 6 6 Figure 16 Link Test Signal Form the test result table you can get: Local Signal Level (dBm): shows the received signal strengthen of local Access Point Remote Signal Level (dBm): shows the received signal strengthen of remote Access Point. View the intensity of signal, and adjust the positions and angles of the antenna according to the intensity of signal. Adjust the antenna, and observe the value of dBm at the same time.
ZDC ZA-5000-D User's Manual V2.3.2 Notice: The signal strengthens (dBm) is negative value, the more little the absolute value of it, the better the signal strengthens. For the better throughput of wireless network, you should better adjust the signal strengthen as better as possible. The signal strengthens (Percent) is just a reference value. It lies on not only the real signal strengthen but also the academic signal strengthen which lies on the Link Test settings.
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 4 Advanced Configuration RADIUS Figure 17 RADIUS RADIUS (Remote Authentication Dial-In User Service) plays a central role in the network in providing the capabilities of authenticating, authorizing, accounting, auditing and alarming…etc and allows an organization to maintain user profiles in a central database that all remote servers can share. Since RADIUS is relatively complex to explain, we will focus here on how it acts as an 802.
ZDC ZA-5000-D User's Manual V2.3.2 environment. Even more, it is also a must-do to accommodate the recently introduced Wi-Fi protected access (WPA-EAP) to wireless networks. z Authentication/Access Control Radius Server Configuration This configuration is required for authentication using Radius. IP Address, Port No. and Shared Secret is required for communication with Radius Server. A Secondary Radius Server can be configured which is used on failure on Primary Radius Server.
ZDC ZA-5000-D User's Manual V2.3.2 Security Setup Figure 18 Security Settings z Authentication Type Choose the following type. Open System: Allow any wireless NIC or wireless bridge connect Shared Key: If Shared Key is selected, you need to enabled WEP and enter at least one shared key. 802.1x: IEEE 802.1x is a standard for network access control (port based), which was introduced especially for distributing encryption keys in a wireless network. The Access Point supports 802.
ZDC ZA-5000-D User's Manual V2.3.2 with a new encryption method called Temporal Key Integrity Protocol (TKIP) implementation with 802.1x dynamic key exchange. WPA+ PSK: Instead of using RADIUS for authentication, systems with WPA-PSK will be configured with a secret password phrase. Enter your password phrase and press “Generate”. You can now create a pre-shared key in the Access Point and copy the characters you input to the station's WPA-PSK entry.
ZDC ZA-5000-D User's Manual V2.3.2 Notice: The Access Point and the stations must have the same Authentication Type, Data Encryption and Key, otherwise they can not connect. Access Control List Setup The optional Access Control window lets you block the network access privilege of the specified stations through the Access Point. This provides an additional layer of security. There are two kinds of ACL.
ZDC ZA-5000-D User's Manual V2.3.2 Add button and Apply button. Add Available Wireless Stations: Select the stations from the wireless station list and click Add button to add to the Trusted Wireless Stations list and click Add button and Apply button. Delete Trusted Wireless Stations: Choose the station in the Trusted Wireless Stations list, click Delete button and Apply button.
ZDC ZA-5000-D User's Manual V2.3.2 Hidden SSID Setup Figure 21 Hidden SSID Setup If set to Yes, the Access Point will broadcast its SSID, allowing Wireless Stations which have a "null" (blank) SSID to adopt the correct SSID. If set to No, the SSID is not broadcast then station can not scan the AP in order to avoid illegal attack. Wireless Isolation The wireless isolation can give the wireless network more security.
ZDC ZA-5000-D User's Manual V2.3.2 The remote Bridges will not be able to communicate with each other if this feature is enabled. Figure 23 Wireless Separator Outdoor Point to Multi-Point Bridge Application In some application structure, there is a wireless bridge as centre point, other bridge access network by connecting it.
ZDC ZA-5000-D User's Manual V2.3.2 textbox after the remote MAC address textbox. Outdoor Wireless Cover Application In the AP mode, it can be set as wireless cover spot. Figure 24 Outdoor Wireless Cover Application STA1 and STA2 connect AP by SSID, and then they can access PC in Ethernet and internet. Do steps as following: 1. Set Operating Mode as AP mode in Wireless Settings page. 2. Open AP Settings page, set basic information.
ZDC ZA-5000-D User's Manual V2.3.2 Enter a 32-character (maximum) Service Set ID in this field; the characters are case sensitive. When in infrastructure mode, this field defines the Service Set ID (SSID). The SSID assigned to the wireless node is required to match the SSID in order for the wireless node to communicate with the Access Point. z Beacon Interval Specifies the interval time (20~~1000ms) for each beacon transmission.
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 5 Management View the General Information Figure 27 General The General Information page displays current settings and statistics of your Access Point that is Read-only, and any change of settings must be made on other pages.
ZDC ZA-5000-D User's Manual V2.3.2 point or client node associated with the Access Point. View the Device’s Link Status Figure 29 Link Statistics This page displays both wired Ethernet and wireless interface network traffic. Click Refresh to update the current statistics. Change Login Password Figure 30 Change Login Password You can use the Change Password page to change the Access Point administrator's password for accessing the Settings pages.
ZDC ZA-5000-D User's Manual V2.3.2 To change the password, Type the old password. The default password for the Access Point is: password. Type a new password and type it again in the Repeat New Password box to confirm it. Click Apply to have the password changed or click Cancel to keep the current password. Be sure to write it down in a secure location and the maximal length of the password is 19 characters. Firmware Upgrade User can't toway modify about firmware.
ZDC ZA-5000-D User's Manual V2.3.2 C:\>ftp 192.168.0.228 Connected to 192.168.0.228. 220 (vsFTPd 1.1.3) User (192.168.0.228:(none)): admin 331 Please specify the password. Password: 230 Using binary mode to transfer files. Login successful. Have fun. ftp> put zag5000.rmt 200 PORT command successful. Consider using PASV. 150 Ok to send data. 226 File receive OK. ftp: 3973128 bytes sent in 0.55Seconds 7263.49Kbytes/sec. ftp> quit 221 Goodbye. Notice: The software must be zag5000.rmt or ZAG5000.rmt.
ZDC ZA-5000-D User's Manual V2.3.2 button, then the AP will restart. z FTP 1. Login AP by ftp. 2. Input command get zag5000.cfg, it will be saved in current directory. 3. Input command put zag5000.cfg, it will retrieve it to AP. and AP will restart. C:\>ftp 192.168.0.228 Connected to 192.168.0.228. 220 (vsFTPd 1.1.3) User (192.168.0.228:(none)): admin 331 Please specify the password. Password: 230 Using binary mode to transfer files. Login successful. Have fun. ftp> get zag5000.
ZDC ZA-5000-D User's Manual V2.3.2 Figure 33 Restore to Factory Click Restore button then the AP will restart to factory. z Hardware Default Button Figure 34 Default Button Press the default button for more than ten seconds while power on the AP. Reboot AP Figure 35 Reboot AP You may select Yes on “Reboot AP” page and then click on APPLY button to reboot the access point.
ZDC ZA-5000-D User's Manual V2.3.2 SNMP Management Figure 36 SNMP AP supports SNMP. At first you should set SNMP settings and get MIB file from AP by ftp. 1. SNMP Settings. a) Set the Trap Server Address: You can find the unusual log on the Trap Server. b) Set the Read-only Community; c) Set the Read-write Community; d) Click the “Apply” button to save setting. 2. Get MIB file by ftp a) Login AP by ftp. b) Input command “get zag5000.mib”,you will find the mib file in the current directory.
ZDC ZA-5000-D User's Manual V2.3.2 C:\>ftp 192.168.0.228 Connected to 192.168.0.228. 220 (vsFTPd 1.1.3) User (192.168.0.228:(none)): admin 331 Please specify the password. Password: 230 Using binary mode to transfer files. Login successful. Have fun. ftp> get zag5000.mib 200 PORT command successful. Consider using PASV. 150 Opening BINARY mode data connection for /mnt/ramd/zag5000.mib (35518 bytes). 226 File send OK. ftp: 35518 bytes received in 0.03Seconds 1183.93Kbytes/sec. ftp> quit 221 Goodbye.
ZDC ZA-5000-D User's Manual V2.3.2 Figure 38 Putty Settings 2 4. Open it. You will see as following figure. Figure 39 SSH 5. The user name is admin and password is password, after login you can use command line to set AP. you can input command “help” to get help. All the command supported is in Appendix D SSH.
ZDC ZA-5000-D User's Manual V2.3.2 Chapter 6 Troubleshooting FAQ Q 1. How to know the MAC address of the Access Point? • The MAC address is written in a label which is in the bottom of Access Point. Figure 40 MAC Address • From the General page of WEB configuration, you also can get the MAC address of AP. Q 2. Why two Access Points can not build connection after setting? • Check the “Operating Mode” whether is “Bridge Mode”. • Check the “remote MAC address” whether is right.
ZDC ZA-5000-D User's Manual V2.3.2 Diagram 9 RF Path Loss M(Meter) 5GHz（dBm） 1 46 2 52 5 60 7 63 10 66 20 72 30 75.6 40 78 50 80 60 81.2 70 83 80 84 90 85 100 86 200 92 300 95.6 500 100 1000 106 3000 116 5000 120 10000 126 15000 130 20000 132 25000 134 30000 136 Example: one pairs of ZA-5000-I, the space between bridges is 3km.
ZDC ZA-5000-D User's Manual V2.3.2 • Wireless Channel/Frequency Try to change other channel • Wireless disturbance Check whether there are other wireless equipments nearby AP; make sure they do not disturb AP. Q 5. The wireless becomes unstable such as ping timed out and lose packet after a period of well work? This situation may the wireless network is disturbed by something, what you can do is following steps: (1).
ZDC ZA-5000-D User's Manual V2.3.2 Appendix A. Technical Specifications Diagram 11 ZA-5000-D Spec ZA-5000-D Dual-RF Outdoor Access Point The next-generation Wireless LAN device － ZA-5000-D 802.11a/b/g Wireless Outdoor Bridge, Unique double RF design can work in 2.4GHz and 5.8GHz at the same time, and concert some operation mode (Bridge Repeater mode、Bridge + AP mode), then agilely settings and performance was be smart improve.
ZDC ZA-5000-D User's Manual V2.3.2 2.4GHz: America:2.412GHz~2.462GHz Japan:2.412GHz~2.484GHz Europe:2.412GHz~2.472GHz China:2.412GHz~2.472GHz RF Output Power 18dBm±2dBm 15.5dBm Sensitivity －65dBm@54Mbps －66dBm@48Mbps －70dBm@36Mbps －74dBm@24Mbps －77dBm@18Mbps －79dBm@12Mps －81dBm@9Mps －82dBm@6Mbps －65dBm@54Mbps －66dBm@48Mbps －70dBm@36Mbps －74dBm@24Mbps －77dBm@18Mbps －79dBm@12Mps －81dBm@9Mps －82dBm@6Mbps －80dBm@11Mbps －83dBm@5.
ZDC ZA-5000-D User's Manual V2.3.2 Appendix B. Glossary Diagram 12 Glossary Glossary Expiation 802.11a IEEE specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 5GHz. 802.11a provides specifications for wireless ATM systems and is used in access hubs. Networks using 802.11a operate at radio frequencies between 5.180 GHz and 5.825 GHz.
ZDC ZA-5000-D User's Manual V2.3.2 reduce the work necessary to administer a large IP network. The most significant piece of information distributed in this manner is the IP address. Encryption For the security of transmit data in network, the data should be encrypted before transmit and decrypt received data. IP Address Internet Protocol is the main internetworking protocol used in the Internet. Used in conjunction with the Transfer Control Protocol (TCP) to form TCP/IP. LAN&WAN LAN.
ZDC ZA-5000-D User's Manual V2.3.2 Appendix C. ASCII You can dispose hexadecimal number system counting or ACSII one yard of keys encrypted as WEP. Hexadecimal number system is made up by 0-9 and A-F (letter does not distinguish capital and small letter); ACSII yard is by 0-9 figures, A-F, a-f (letter distinguishes capital and small letter), and the punctuation mark makes up. Each ACSII yard can is it says to count by one hexadecimal number system of two.
ZDC ZA-5000-D User's Manual V2.3.2 Appendix D.
ZDC ZA-5000-D User's Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.2 √ √ rate --- wireless transmission data rate √ √ ssid --wireless name(1-32chars) √ √ power --- wireless transmit power √ √ fragmentati onthreshold --- wireless fragmentation threshold (even only) √ √ rtsthreshold --wireless threshold √ √ super --- enable Super-A/G mode √ √ beaconinter val --- wireless beacon period in TU(1024us) √ √ dtim --- wireless DTIM period in beacon interval √ √ preamble --- wireless preamble(only effect on 802.
ZDC ZA-5000-D User's Manual V2.3.
ZDC ZA-5000-D User's Manual V2.3.
