User's Guide

WIIBOOX LIGHT-3D Printer User Guide
WIIBOOX LIGHT-3D
打印机用户指南
Page 16 of 16
If there is light, but the LCD module cannot properly project the picture, it is necessary to replace the LCD module.
四、打印模型与设计模型不一样
Ⅳ. Print model is different from design model
1.确保模型设计正确，网格没有包含任何错误。
2.更换较好质量的 U 盘,或复制文件至打印机在打印
1. Make sure the model is designed correctly and the grid contains no errors.
2. Replace better quality U flash or copy files to printer, then print.
五、打印机操作界面无反应
Ⅴ. The printer interface is no response
将打印机断电强重启
Turn off the printer and forced to restart it
六、其他打印故障
Ⅵ. Other Printing Failures
打印模型出现不规则断裂：检查材料盘薄膜是否发白或者穿孔损坏
打印模型表面有穿孔：使用检测曝光功能查看 lcd 成型模块是否存在黑点
The printing model has irregular fracture: check whether the film of material plate is white or damaged by perforation
The print model has a perforated surface: use detection exposure function to check whether there are black spots in the LCD
forming module
回收 Recovery
处理纸张和塑料包装
Disposal paper and plastic packaging
为了保护环境，制造商建议放置用过的纸张和塑料包装在专门指定的容器中，根据您当地的回收准则。处理树脂,
打印和后处理废物，包括空瓶，打印失败，支撑，筏以及带树脂残留物的纸巾应放在紫外线站或任何地方处理前的
紫外线光源。未固化的树脂必须按照处理关于危险废物的国家和地方法规。关于所用液体洗涤剂的使用和废物处理
的详细信息。
In order to protect the environment, manufacturers recommend placing used paper and plastic in specially designated
containers, in accordance with your local recycling guidelines. Printing and post-treatment waste should be cured under
ultraviolet light, including empty bottles, printing failure, support, backing, and paper towels with resin
residues.Unsolidified resins must be treated in accordance with national and local regulations for hazardous wastes.
Detailed information on the use of liquid detergents and waste disposal is found in the MSDS file provided by the
manufacturer.
清洁 3D 打印应该在液体生产商提供的 MSDS 中找到。设备中包含的物质可能是对自然环境有害。废电器和电子设
备不能在垃圾填埋场处理，必须回收。有关何处处置的信息废弃设备，请联系经销商，制造商或设备的进口商。废
弃电气和电子设备与其他废物一起处理。如有问题，请通过售后支持与制造商联系
Clean 3D printing should be found in MSDS provided by liquid manufacturers. The substances contained in the equipment
may be harmful to the natural environment. Waste electrical and electronic equipment cannot be disposed of in landfills and
must be recycled. For information on the place to dispose of obsolete equipment, please contact the dealer, manufacturer
or importer of the equipment. Waste electrical and electronic equipment is disposed of with other wastes. If you have any
questions, please contact the manufacturer through after-sales support.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body.