User's Guide

WIIBOOX LIGHT-3D Printer User Guide
WIIBOOX LIGHT-3D
打印机用户指南
Page 15 of 16
4.将清洁干净并风干的材料盘装入打印机固定。
4. Fix the clean and air-dried material tray into the printer.
5.装入新的材料盒并开启自动进料开关，加材料 5 分钟
5. Install the new material box and turn on the automatic feeding switch. Add the material for 5 minutes.
无自动进料功能的设备直接往材料盘注入新的材料，树脂量必须符合材料盘标识的范围。
The equipment without automatic feeding function injects new materials directly into the material plate, and the resin
content must conform to the scope of the material plate marking.
6.完成材料更换，关闭防尘遮光盖。
6. Complete material replacement and close the dustproof and shading cover.
可用材料 Available Materials
建议使用制造商指定材料，制造商只提供指定材料对应的参数
It is recommended to use the materials specified by the manufacturer. The manufacturer only provides the parameters
corresponding to the specified materials.
基本维护和服务工作 Basic Maintenance and Service Work
维护工作应定期进行，以保持打印机的良好状态，获得高质量的打印产品。
Maintenance should be carried out regularly in order to keep the printer in good condition and obtain high quality printing
products.
在开始任何维修之前，正常关闭打印机，让它冷却下来。
Before starting any repairs, shut down the printer and let it cool down.
设备内部有高压电，在任何维护、维修之前必须拔掉电源线，避免触电
There is high voltage power inside the equipment. Before any maintenance and repair, the power cord must be unplugged to
avoid electric shock.
打印机配有执行维护服务所需的相关工具
Printers are equipped with the tools needed to perform maintenance services.
丝杆和导轨：定期检测是否有充足的润滑油
Lead screw and guide rail: periodically check whether there is enough lubricant
清洁机器:使用柔软的布料擦拭，不能使用 IPA 或化学清洁剂
Clean machine: Use soft cloth to wipe. Do not allow to use IPA or chemical cleaner.
清洁液晶显示屏屏幕：使用柔软的布料擦拭，可适当的喷洒 IPA 后擦拭干燥
Clean LCD screen: use soft cloth to wipe. Spray IPA properly and wipe dry.
清洁材料盘：在材料盘中添加一部分 IPA，使用软纸巾或柔软的布料擦拭
Clean material plate: Add a part of IPA to the material plate and wipe it with soft paper towel or soft cloth.
更换材料盘薄膜：参考打印机所配资料 USB 储存器内的更换材料盘薄膜视频
Replace material plate film: Refer to the replacement material disk video in the USB storage packet provided by the
printer.
支持和故障排除 Support and Troubleshooting
为了确保每个 3D 打印机用户的安全，制造商提供各种服务支持，同时解决技术问题。如果操作此打印机有困难，
首先应该寻求指导。在本用户指南中，请查看提供的手册。下面列出了最常见的问题以及可能的解决方案。
In order to ensure the safety of each 3D printer user, the manufacturer provides a variety of service support, and solves
technical problems. If it is difficulty to operate this printer, you should firstly seek guidance. In this user guide, see the
manual provided. The most common problems and possible solutions are listed below.
一、在打印过程中，打印件不会粘附到平台上
Ⅰ. During the printing process, the print will not stick to the platform
1.确保模型设计正确，网格没有包含任何错误。
2.确保在切片中准备文件时选择了对应材料的参数设置，即打印设置与使用的树脂类型相匹配。
3.确保平台和材料盘都是干净的，没有任何的固化树脂残留物或其他杂质。
4.确保液体树脂中没有固化残留物。
5.再次进行平台校准检测。
6.检查材料盘膜是否弯曲，变形或穿孔。如果，请更换材料盘薄膜
1. Make sure the model is designed correctly and the grid contains no errors.
2.Make sure that the parameter set of the corresponding materials are selected when preparing the files in the slices, that is,
the print set match the resin type used.
3. Make sure the platform and material plate are clean and free of any residual resin or other impurities.
4. Make sure there is no solidified residue in the liquid resin.
5. Platform calibration test is carried out again.
6. Check whether the material plate is bent, deformed or perforated. If so, please replace the material disc film.
二、打印品分层或不粘附在支撑结构上
Ⅱ. The print product is layered or does not adhere to the support structure
1.确保模型设计正确，网格没有包含任何错误。
2.如果支撑结构是在不同的程序中生成的，确保模型的网格是固定的。
3.确保准备文件时选择了合适的打印配置文件，即打印设置与使用的树脂类型相匹配。
4.检查材料盘薄膜是否松动，弯曲，变形或穿孔。如有，请更换材料盘薄膜
5.检查材料量是否充足，根据材料盘标识范围计算
1. Make sure the model is designed correctly and the grid contains no errors.
2. If the support structure is generated in different programs, ensure that the mesh of the model is fixed.
3. Make sure that the appropriate print configuration file is selected when preparing the file, that is, the print settings match
the type of resin used.
4. Check whether the material plate film is loose, bent, deformed or perforated. If yes, please replace the material disc film.
5. Check whether the material quantity is sufficient, and calculate according to the marking range of the material disc
三、打印完成后发现打印平台和材料盘中均无固化物
Ⅲ. After printing, it is found that there is no solidified material on the printing platform and material plate
1、确保模型设计正确，网格没有包含任何错误。
2、将打印平台和材料盘依次取下，打开曝光检测画面（请使用挡光板遮挡出料口），观察曝光是否正常：
如无任何光线，则需要更换打印机内部光源
如有光线，但 lcd 模块无法正常投射画面，则需要更换 lcd 成型模块
1. Make sure that the model is designed correctly and that the grid does not contain any errors.
2. Take out the printing platform and material plate in turn, open the exposure detection screen (please use the light barrier
to shield the outlet), and observe whether the exposure is normal:
If there is no light, replace the printer internal light source.