User's Guide

WIIBOOX LIGHT-3D Printer User Guide
WIIBOOX LIGHT-3D
打印机用户指南
Page 14 of 16
material bottles for more than 7 days in order to avoid the deterioration in the air for a long time.
* Printers and materials cannot be placed in the sunshine location or window. The large amount of ultraviolet light
contained in sunlight can make the material solidify and scrap.
* Do not place under spotlights or other strong LED lights.
9.打印机长时间不使用回收材料
将过滤漏斗插入瓶子中,将材料盘的树脂通过漏斗倒入瓶中。如果有必要，可以使用纸牌等纸质卡片对料盘进行清
理。
9. Printers do not use recycled materials for a long time
The filter funnel is inserted into the bottle, and Pour the resin on the material plate into the bottle through a funnel. If
necessary, paper cards such as cards can be used to clean the plate.
10.用纸巾和 95°酒精清洗剂擦拭材料盘。
10. Wipe material dishes with paper towels and 95°alcohol detergent.
11.用干净的软布清洁 LCD 屏幕和 FEP 薄膜的外部
11. Clean the LCD screen and exterior of FEP film with clean soft cloth.
12.将清理干净的材料盘安装回打印机中
12. Install the clean material plate back into the printer.
关于打印失败的处理 Treatment of Print Failures
*.此项说明仅在打印的模型脱离平台、支撑与模型脱离、模型断裂的情况适用。如有其他原因导致的打印失败，请
在故障排除项内寻找解决方案或联系售后支持解决。
* This explanation is applicable only when the printed model is separated from the platform, the support is separated from
the model and the model is breakage. If printing fails due to other reasons, please find solutions in troubleshooting items or
contact after-sales support to solve them.
*必须佩戴防护手套、眼镜
* Protective gloves and glasses must be worn
1. 将打印品台取出清理干净
1. Take out the print product platform and clean up.
2. 使用料盘清扫功能对材料盘树脂固化一层
2. Solidify the resin layer of the material plate by cleaning function of the material plate.
3. 将固化物沿料盘边缘取出并及时擦拭洒在设备上的液体材料。
3. Take out the solidified material along the edge of the plate and wipe the liquid material on the equipment in time.
4.清理完成，安装平台至打印机即可
4. Clean up and install the platform to the printer.
更换材料 Change the material
1. 将材料盒取出，打开自动进料开关，使自动进料系统运行 1 分钟，将上一次剩余在管内的材料流进材料盘，以
减小对新更换材料的污染（同型号材料的更换忽略此步骤）。
1. Take out the material box, and open the automatic feeding switch so that the feeding system run asthmatically for 1
minute, and flow the remaining material in the tube into the material tray in order to reduce the pollution of the new
replacement material (the replacement of the same type material ignores this step).
2.取下材料盘
*如果经常更换材料，制造商建议购买多个材料盘替换，以减少繁杂的操作、材料的损耗以及对材料盘的损害。
2. Take out the material tray
* If material is replaced frequently, the manufacturer suggests purchasing multiple material plate to replace them in order to
reduce complicated operation, material loss and damage to the material disks.
3.将树脂过滤漏斗插入瓶中，倒入树脂。如有必要，请用纸牌等纸质卡片对料盘进行清理。完成后，用液体洗涤剂
或异丙醇清洁材料盘。
3.Insert the resin filter funnel into the bottle and pour in the resin. If necessary, clean the plate with cards and other paper
cards. After completion, clean the material tray with liquid detergent or isopropanol.