User's Guide
Table Of Contents
- Workplace health and safety工作场所健康与安全
- Electric Safety 电气安全
- Safety of Machinery 机械安全
- Burn Risk烧伤风险
- Safe Storage安全储存
- About "Wiibox Linght" 有关“Wiibox Linght”
- How does it work?如何运作？
- 产品规格Product Standard
- 建议环境
- Suggestion environment
- 包装清单Pack list
- 主要部件Main part
- 3D打印技术词汇 3D Printing Technology Term
- 首次使用准备工作Preparation Work for First Use
- 切片支撑软件“wiibooxslicer”使用
- Use of Slice Support Software "wiibooxslicer"
- 启动打印 Start Printing
- 后处理Post—process
- 关于打印失败的处理Treatment of Print Failures
- 更换材料Change the material
- 可用材料Available Materials
- 基本维护和服务工作Basic Maintenance and Service Work
- 支持和故障排除Support and Troubleshooting
- 回收Recovery
WIIBOOX LIGHT-3D Printer User Guide
WIIBOOX LIGHT-3D
打印机用户指南
Page 11 of 16
9. Export "dis" file
10.通过 U 盘传输至机器
10. Transfer to machine by U flash
启动打印 Start Printing
警告！
在所有操作程序中必须佩戴手套和眼镜。
准备好纸巾并将其放在工作场所以擦拭液体。
Warning!
Gloves and glasses must be worn in all operating procedures.
Prepare paper towels and place them in the workplace to wipe the liquid.
注意！
打印和后处理废物，包括空瓶，打印失败，支撑，底板，以及带树脂残留物的纸巾应放在紫外光下进行固化处理。
未固化的树脂必须按照处理关于危险废物的国家和地方法规。关于所用液体洗涤剂的使用和废物处理的详细信息在
制造商提供的 MSDS 文件中找到。
Notice!
Printing and post-treatment waste should be cured under ultraviolet light, including empty bottles, printing failure, support,
backing, and paper towels with resin residues. Unsolidified resins must be treated in accordance with national and local
regulations for hazardous wastes. Detailed information on the use of liquid detergents and waste disposal used is found in
the MSDS file provided by the manufacturer.
1.检查设备： 如果在打印机安装过程中未检测平台校准，请执行这个程序。
检查设备电源接通情况，确保稳定的电路环境
打印机材料盘是否干净、安装是否稳固
打印平台是否干净、安装是否稳固
检查完成后关闭防尘遮光盖
1. Check equipment: If the platform calibration is not detected during the printer installation, please execute this procedure.
Check power connection of equipment to ensure stable circuit environment. Whether the printer material plate is clean and
the installation is stable. Whether the printing platform is clean and installation is stable. Close the dustproof shading cover
after inspection.
2. 添加材料： 将储料盒轻微摇晃半分钟，避免因静止而导致的材料沉淀。
料摇晃后倒入打印机材料盘中，材料量不可超过图示台阶位置。
2.Additional material: Gently shake the storage box for half a minute to avoid sediment of the material due to static.
After the material is shaken, pour it into the printer material tray. The amount of material should not
exceed the position of the step shown.
3.将通过“wiibooxslicer”处理好的 DJS 文件放置到 U 盘，并按以下顺序操作打印机（WIFI 打印请参见独立的 wifi 操
作说明书）。
3. Use preparation work Store the .DJS file processed by "
wiibooxslicer
" onto a USB flash drive and operate the printer in
the following order (please refer to separate WIFI operating instructions for WIFI printing).
a.进入文件选择栏 b.打开“sda1”（sda1 为当前插入的 U 盘）
a. Enter the file selection bar b. Open "sda1" (sda1 is the U disk currently inserted)