FB Michigan Owner’s Manual WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT as that specified by Michigan in this manual. Failure to comply with this government regulation could void your authority to operate the equipment. CAUTION A RISK OF ELECTRIC SHOCK. DO NOT OPEN! CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
10. Memory Button This button is used to store broadcast stations into the memory for future recall. 11. Tuning Mode selector Switches between automatic tuning and manual tuning. 12. Preset Buttons Serve to select FM or AM broadcast stations stored in the preset station memory of the unit 13. Tuning Buttons Serve to tune broadcast stations during manual or automatic tuning. 14.
20. Jumper Plugs When the Pre Out Main In connectors are not used, the supplied jumper plugs must be inserted in the jacks. Otherwise the sound is cut off from the speaker and headphone outputs. * If jumper plugs are removed or inserted while the unit is switched on, noise bursts may damage the speakers. Be sure to sat the Power switch to "Off before altering any jumper connection. 21. Speaker Output Terminals 22. Power Cord Remote Control Unit 1. Tape Deck Selector (RE-1) 2. Tape Deck Control Buttons 3.
* Tape Deck Operation Table Emote control button << >> < Reverse > ® Cue a Morel Rewind Fast forward = Playback Recording Fast-forward Stop Pause standby * 100(DAT) CR-TA Fast-forward % # LG-54 CHRAMNCRANVCR DRAGON # Reverse Forward Recording * Curing » # playback playback RX-505 » ” Tape reversal | Playback RX-303 Southeastward # F0001000 10002xL Curing 5 # 700/700 Fast forward # # TO0ZXLIT00ZXE Curing % 5 ZX-3ZK-7 EX-300 Recording Sop # # standby * Recording Fast-forward * # BR2ZXIGB1IX/BB0ZX/BE0 Using %
Connections Dent towards dynamiter : 7 Supped Dipole Glans EM Antenna Twinkling 300. 0h Cable ST STS OE, SON tt: inn dal Videos: Player, VOR ele. dss To Video Output Terminal To Visa inp Stemming Terminal BH To ludo Cup Terminals (1 BH) To Radio Input a) To Be mole Sensor Hem RSS | Ls The Chart shows the BE-1.
low resistance, designed specially for audio applications. Using thin cable with high resistance may impair sound quality and prevent the receiver from desalinating its full potential. + The speaker cables for both channels should be approximately equal in length, as a marked difference can result in improper left right balance, = Pay close attention to the power handing capability of connected loudspeakers.
Memory Tuning A total of 10 FM/AM stations can be programmed in the memory of the receiver at random, for instant recall. 1. Tune the receiver to the desired broadcast station. 2. Press the Memory button. The Memory indicator lights up for about 5 secants. 3. While the indicator is it, choose the desired preset station number with the Reset A (Up) or v (Down) button. 4, While the Memory indicator is still it, press the Memory button again. The indicator goes out and the selected station is stored, 5.
Suppression: Better than 80 dB [AM] Note: Modulation «= 400 Hz, 30% = Frequency Range: 520 = 1,710 kHz in 10 kHz steps / *'522 — 1611 kHz in 9 kHz steps » Sensitivity: 53 dBm » Signal-to-Noise Ratio at 90 bedbug: Better than 52 dB = Total Harmonic Distortion at 90 DBMS: Less than 0.5 % * Selectivity: Better than 20 dB (£10 kHz / *'9 kHz) General » Power Source: 120, 230 or 240 V AC, 50/60 Hz (According to country of sale) * Power Consumption: 390 W max.
