Owner’s Manual UWS-100 100-Channel Select UHF Wireless System
Contents System Features Introduction.............................................................................................................................. 2 UWS-100 System • UHT-100 Handheld Mic Transmitter Using this Manual..................................................................................................................... 2 • Unsurpassed state-of-the-art PLL UHF performance with 120dB dynamic range and operation, up to 500 ft.
Quick User Controls Guide 1. UWS-100 Receiver: Front View 2. 3. 1 4. 5. 6. UWS-100 UHF PLL WIRELESS SYSTEM DigiTRU Diversity™ ASC™ SYSTEM A AF A SEL ECT CHA NNEL 2 3 7. RF B 4 B IR 5 ASC 6 7 UWS-100 Receiver: Back View 15VDC IN 400mA POWER LINE OUT UNBALANCED 8 9 10 11 8. 9. 10. 11. 12. 13. 14. DC INPUT JACK For connecting external AC/DC adapter to power receiver (DC15VDC/400mA) POWER ROCKER SWITCH Press right side to turn On or press left side to turn Off receiver.
Quick User Controls Guide Quick User Controls Guide UHT-100 Handheld Transmitter: Front and Back UB-100 Bodypack Transmitter 40 24 15 16 17 18 25 16A 41 26 42 16C 16B LO BAT OFF ON STDBY 19 20 UHT-100 NADY 27 27B UBT-100 21 28 22 27A 29 IR ASC™ SYSTEM 23 30 31 15. MIC BALL Windscreen 16 A. LCD DISPLAY: CHANNEL Indicates channel (00‑99) 16 B. LCD DISPLAY: BATTERY Indicates battery status from one (weakest) to five (strongest) bars. Flashing “BATT” indicates low battery 16 C.
System Operation UWS-100 Receiver Powering the Receiver To power the receiver, plug the provided DC POWER SUPPLY UNIT (14) adapter into the DC INPUT JACK (8) on the back of the receiver, then plug the adapter into a 120VAC outlet. Note: Any 15-18VDC source with minimum 400mA capacity can also be used. The Power Rocker Switch (9) is used to turn the receiver on or off. To turn on, press down the right side of the switch (“I”). The LED Display (3) will light, showing Channel 00‑99.
is controlled by the Volume Control (12). For unbalanced line output connection, plug an audio cable with a ¼” mono (Tip/Sleeve) plug into the Unbalanced Line Out jack and plug the other end into your mixing board or amplifier. Adjusting the Volume control will increase or decrease the audio level at the ¼” Unbalanced Line Out only. When using the UBT-100 instrument transmitter system, connect the Unbalanced Line Out directly to your instrument amp or preamp.
Operating the UHT-100 Handheld Transmitter The Off/Stby/On POWER SWITCH (18) has three positions and functions both as a power On/Off and as an audio mute On/ Standby switch. During normal operation with the unit powered on standby, slide the Off/Stby/On power switch to the ON position. You will feel a slight click indicating the ON position is selected. The receiver’s RF A/B LED (5) diversity indicators should now be on, indicating a received signal from the transmitter.
After the unit is powered on, slide the power switch to the ON position to un-mute the audio or to STBY to mute the audio. Set the power switch accordingly and the transmitter is now ready to use. The receiver’s RF A/B LED indicator should now be on, indicating a received signal from the transmitter. slide the power switch to STBY again. Adjust the volume of the receiver per the previous section, Connecting the Audio Output.
Miscellaneous Tips • The receiver antennas should be kept away from any metal surfaces whenever possible as they can reflect away or shield the incoming RF signal. • If the receiver’s volume control is set too high, it may overdrive the input of the attached audio mixer, causing distortion. Conversely, if the output is set too low, the overall signal-to-noise ratio of the system may be reduced, causing noticeable hiss.
Frequency Plan One Year Limited Warranty Band 1: 667.000-696.700MHz (U.S.) 100 Channels / 300 KHz per step Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects in material or workmanship for a period of one year from the date of original retail purchase. If any such defect is discovered within the warranty period, Nady Systems, Inc.
6701 Shellmound Street | Emeryville, CA USA 94608 T 510.652.2411 | F 510.652.5075 | www.nady.
