Dual Receiver VHF Wireless Microphone System Nady Wireless Systems are type accepted under FCC rules parts 90, 74 and 15. The device complies with RSS-210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. NADY SYSTEMS, INC.
CONTENTS CONTENTS ...........................................................................................2 INTRODUCTION ....................................................................................3 USING THIS MANUAL ...........................................................................3 SYSTEM FEATURES ................................................................................4 ENCORE DUET RECEIVER .......................................................................
INTRODUCTION ENCORE DUET RECEIVER Reception Mode Controls Connectors LED Indicators Dimensions (Max.) Weight Power Requirements Antenna Dual receivers (Channel A and Channel B) Power ON/OFF, dual volume and mute controls (one each, Ch A/B) Dual balanced XLR and unbalanced adjustable 1/4" audio out jacks (Ch A & B mixed), 2.1mm barrel-type DC input jack Power ON, Dual 5-LED RF & AF level displays (Ch A/B) 1.75" x 7.5" x 8.1" (4.4 x 19 x 20.7 cm) 1.6 lbs (.
SPECIFICATIONS SYSTEM FEATURES • Dual channel system for simultaneous operation of two transmitters • Available on 2 selected frequencies in the VHF high band (171-216 MHz) for interference-free, long-range performance • Proprietary companding circuitry for an industry-best 120dB Dynamic Range, and the clearest, most natural sound available • Operating Range: Up to 250 feet typical (depending on site conditions) – up to 500+ feet line-of-sight • Noise-free transmitter ON-OFF operation • Rugged, foam-padded
ENCORE DUET RECEIVER 1. Rackmounting the Receiver There are 2 options available for rackmounting the Encore DUET receiver: singly or side-by-side with another Encore Series receiver. a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of the receiver (as shown) and slide in the optional ERM-12 RACK EARS (9). b.
5. Connecting the Audio Output The Encore DUET receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (14) for each channel and an adjustable line level A + B UNBALANCED AUDIO OUTPUT 1/4" JACK (13) which provides a mixed (summed) Ch A plus Ch B output signal. The mixed level from the A + B UNBALANCED OUTPUT is controlled by the rear panel VOLUME CONTROLS (6) for each channel.
THE LINK 2™ PLUG-IN TRANSMITTER 16 16 1. Transmitter Set-Up First, slide open the BATTERY COMPARTMENT DOOR (43) to expose compartment. Insert a fresh 9V ALKALINE BATTERY (45), observing polarity. Close the battery compartment door. 2. Handheld Microphone Installation • Step 1 - Rotate the transmitter's threaded LOCKING RING (37) clockwise toward the XLR CONNECTOR (36) until it stops. • Step 2 - Hold your mic in one hand and The Link 2 in the other. • Step 3 - Plug your mic into the XLR CONNECTOR.
WHT HANDHELD MICROPHONE TRANSMITTER 32 1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed on completely. A fresh alkaline battery can last up to 16 hours in use, but in order to ensure optimum performance, it is recommended that you replace the battery after every 10 hours of use. 35 34 33 32 2.
WGT INSTRUMENT BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31), observing the correct polarity. Close the compartment. The WGT is provided with a 3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes or instrument strap.
WLT LAVALIER/LAPEL OR HEADWORN MICROPHONE BODYPACK TRANSMITTER 24 1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23), observing the correct polarity. Close the compartment. 2. The WLT is provided with a 3.5 mm LOCKING JACK (24) for connecting the microphone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN MICROPHONE (26), as supplied. To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug, reverse the process.
