User Manual
Table Of Contents
- 1.Product Introduction
- 2. Barcode setting
- 2.1 Mark Setting
- 2.2 Basic barcode setting
- 2.2.1 Turn on/Turn off configuration code
- 2.2.2 Restore factory default
- 2.2.3 Read version number
- 2.2.4 Product user configuration
- 2.2.5 Upper PC and Notepad upload settings
- 2.2.6 Interface mode setting
- 2.2.7 Serial port setting
- 2.2.8 Lighting control
- 2.2.9 Control character escape
- 2.2.10 GS Control character escape(need to turn on
- 2.2.11 Prefix setting
- 2.2.12 Suffix setting
- 2.2.13 Unicode Output Mode
- 2.2.14 Virtual keyboard
- 2.3 Buzzer , LED indicator barcode and vibration p
- 2.4 Timeout between decodes (Same barcodes)（Self-i
- 2.5 USB keyboard update speed setting
- 2.6 OA & LF setting（USB keyboard）
- 2.7 USB keyboard text-transform
- 2.8 Keyboard layout setting
- 2.9 Symbologies
- 2.9.1 enable/disable all symbologies
- 2.9.2 Codabar
- 2.9.3 Codabar start/ending character setting
- 2.9.4 Codabar limitation of length
- 2.9.5 Code 39
- 2.9.6 Code 39 check bit
- 2.9.7 Code 39 Full ASCII
- 2.9.8 Code 39 limitation of length
- 2.9.9 Code 32 (Code 39 needs to be enabled）（Not En
- 2.9.10 Interleaved 2 of 5 （ITF5）
- 2.9.11 Interleaved 2 of 5 （ITF5）check bit
- 2.9.12 Interleaved 2 of 5 （ITF5）length setting
- 2.9.13 Interleaved 2 of 5 Limitation of length
- 2.9.14 Industrial 2 of 5 (Industrial 25code)（4-24b
- 2.9.15 Industrial 2 of 5 Limitation of length
- 2.9.16 Matrix 2 of 5 (matrix 25 code)（4-24 bit）
- 2.9.17 Matrix 2 of 5 Limitation of length
- 2.9.19 Standard 25Limitation of length
- 2.9.20 Standard 25 check bit setting
- 2.9.21 Code 93
- 2.9.22 Code 93 Limitation of length
- 2.9.23 Code 11（Not Enabled）
- 2.9.24 Code 11 check bit output（Not Enabled）
- 2.9.25 Code 11 check bit option（Not Enabled）
- 2.9.26 Code 11 Limitation of length（Not Enabled）
- 2.9.27 Code 128
- 2.9.28 Code 128 Limitation of length
- 2.9.29 GS1-128(requires CODE 128 to be enable）
- 2.9.30 ISBT-128
- 2.9.31 Plessey
- 2.9.32 Plessey Limitation of length
- 2.9.33 Plessey check bit optional
- 2.9.34 MSI plessey
- 2.9.35 MSI plessey Limitation of length
- 2.9.36 MSI plessey check bit output
- 2.9.37 MSI plessey Check mode selection setting
- 2.9.38 UPC-A
- 2.9.39 UPC-A check bit
- 2.9.40UPC-A to EAN-13
- 2.9.41 UPC-E
- 2.9.42 UPC-E check bit
- 2.9.43 UPC-E expand UPC-A
- 2.9.44 EAN/JAN-8
- 2.9.45 EAN/JAN-13
- 2.9.46 UPC/EAN/JAN extra-code
- 2.9.47 EAN13 to ISBN
- 2.9.49 GS1 DataBar（RSS14）(Stacked)
- 2.9.51 GS1 DataBar Limited
- 2.9.53 GS1 DataBar Expanded
- 2.9.54 PDF417
- 2.9.56 QR Code
- 2.9.57 Micro QR
- 2.9.58 Data Matrix
- 2.10 User-defined prefix setting
- 2.11 User-defined suffix setting
- 2.12 Barcode prefix&suffix order selection
- 2.13 Code ID setting
- 2.14 AIM ID setting
- Appendix
- Some feature configuration instructions and exampl
第
24
页 共
72
页
2.4.2 Reading time
Single reading time
In the inductive reading mode, this parameter refers to the maximum length of time that the reading
engine is allowed to continue to collect and recognize before the reading is successful. After a successful
reading or a single reading timeout, the reading engine will enter an interval that does not capture the
reading. The single reading time setting range is 0.1~25 seconds and the step size is 0.1 second.
Indicates that the reading time is infinitely long. The default duration is 3.0 seconds.
2.5 USB keyboard update speed setting
There barcode is used to set the update speed when scanner is in USB keyboard pattern. If the
performance of your PC is lower, we suggest you choose slow update speed to make sure the scanner
update the right data.
Slow update speed (default)
Middle update speed
Fast update speed (default)
Custom update speed (2ms~50ms)