Owner's Manual
Table Of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- INTRODUCTION
- IDENTIFICATION OF CONTROLS
- OPERATION
- USING THE T 748 - MAIN MENU
- USING THE T 748 – SETUP MENU
- SETUP MENU
- SOURCE SETUP
- Source Setup (Normal)
- Source Setup (Table)
- iPod SETUP
- Speaker Setup
- AUTO CALIBRATION
- Speaker Configuration
- Speaker Levels
- Speaker Distance
- Adjusting the Volume
- Amplifier Setup
- HDMI setup
- Listening Mode Setup
- Listening Modes
- DOLBY DIGITAL SURROUND MODES
- Dolby Setup
- DTS Setup
- DTS SURROUND MODES
- ENHANCED STEREO
- Display Setup
- A/V Presets SETUP
- AUTO POWER DOWN SETUP
- LISTENING TO AM/FM RADIO
- LISTENING TO DAB RADIO
- OPERATION
- REFERENCE
IDENTIFICATION OF CONTROLS
FRONT PANEL
1 STANDBY BUTTON
• Press this button to switch ON the T 748 from standby mode. The
Standby LED indicator will turn from amber to blue and illuminate
the VFD. Pressing the STANDBY button again turns the unit back to
standby mode.
2 STANDBY LED
• This indicator will light up amber when the T 748 is at standby
mode.
• When the T 748 is powered up from standby mode, this indicator
will illuminate blue.
3 NAVIGATION and ENTER BUTTONS
The navigation [ a/s/d/f ] and [ENTER] buttons have various
applications specic to given modes. The middle round button is
designated as [ENTER] button; this is normally pressed to complete a
selection, procedure, sequence or other applicable functions.
AM/FM mode
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Tune” mode.
• Pressing momentarily the [ a/s ] buttons will manually scan the AM
or FM band.
• Press and hold [ a/s ] for more than 2 seconds to search up/
down;the T 748’s tuner will stop at the next suciently strong signal
it encounters.
• Note that this function “wraps” - that is, it will continue to search
from one end of the AM or FM band to the other until it stops at a
strong signal.
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Preset” mode.
• Use [ d/f ] to step up or down AM/FM Presets. Unused presets are
skipped over. Note that Presets must have been previously stored.
Refer also to the item about STORING PRESETS (AM/FM) at the
LISTENING TO AM/FM RADIO section of the OPERATION page.
DAB mode (230V version model only)
• Use front panel [ a/s ] and [ENTER] buttons in combination with
[MENU] button to select through applicable DAB menu options.
4 MENU
• Press to activate or deactivate OSD menu.
• At DAB mode, use the [MENU] button in combination with the front
panel [ a/s ] and [ENTER] buttons to activate DAB menu options.
5 LISTENING MODE
• Toggle to select through the various Listening mode options.
• Depending on the format of the currently selected input (digital
or analog, stereo or multichannel), various listening modes are
available.
• Refer also to the item about LISTENING MODE under the USING THE
T 748 - MAIN MENU segment of the OPERATION section.
6 VACUUM FLUORESCENT DISPLAY (VFD)
• Displays visual information about the current settings like the active
Source, volume level, listening mode, audio format, applicable RDS/
DAB as well as iPod-related display information and other related
indicators.
• Refer also to the item about DISPLAY SETUP under the USING THE
T 748 - SETUP MENU segment of the OPERATION section.
7 REMOTE SENSOR
• Point the AVR 4 remote control at the remote sensor and press the
buttons.
• Do not expose the remote sensor of the T 748 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the T 748 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
3 4 5 6 7 8
10
D ECB
1 2
A
1211
9
6
ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ