Owner's Manual

SPEAKER SETUP
After connecting all ancillary sources and other combinations, the Speaker
Setup menu will guide you on how to manage and setup your speakers in
order to achieve optimum sound acoustics in your listening environment.
The following are the Speaker Setup Menu sections.
AUTO CALIBRATION
It has been shown that many, if not most, surround sound systems are not
accurately setup and calibrated. To be done properly, calibration requires
special knowledge and instrumentation that the average person probably
doesn’t possess.
The Auto Calibration featured in T 748 uses a microphone, along with
sophisticated digital electronics built into your T 748, to automatically setup
and calibrate the T 748 to the exact speakers and speaker placement of
your own unique Home Theatre.
The following parameters are automatically measured and adjusted
accordingly.
• NoiseLevel: Check noise level relative to each speaker and subwoofer.
• NumberofSpeakers: Speaker conguration is detected including
number of surround speakers and whether a subwoofer and center
channel is connected.
• SpeakerDistance: Accurately set the appropriate distance of
each speaker position as well as the subwoofer with respect to the
microphone position.
• SpeakerLevelandSize: T 748 crossover is set based on each
channel’s signal handling capability and the subwoofer crossover
is automatically set. SPL (Sound Pressure Level) of each speaker is
matched with respect to the microphone position.
• Equalization: Adjust tonal quality (bass/treble level) for each speaker.
This applies to all sound elds and for each speaker.
This is a one-time set up, unless speakers are moved or changed, in which
case the calibration should be performed again.
MEASUREMENT IS THE FIRST STEP.
Connect the microphone jack into the front panel’s MP/MIC input. Place the
supplied microphone in the listening position at about the same height as
your listening ears. The microphone has a threaded insert at its base that
makes possible for it to be mounted on a tripod.
The sound at your main listening position is setup using the supplied
microphone. Depending upon the availability of speakers, you can
select either 7.1 or 5.1 setup. Upon selection of either 7.1 or 5.1, the auto
calibration starts – refer to the OSD as auto calibration steps through each
measurement parameter.
A special test tone is sent to each speaker and the data is memorized
by the T 748. The duration of setup may take some time depending on
the number of speakers. After the measurements, the T 748 calculates
the ideal system response for your particular room and speaker setup. If
some inconsistencies or discrepancies are detected during the setup, the
process maybe interrupted or the problem is shown in the particular setup
window. A notice screen is correspondingly displayed. After following and
undertaking the displayed instructions, re-start the Auto Calibration setup
again. When the measurements are nalized, the ideal system response is
calculated for your particular room and speaker setup.
NOTES
• Autocalibrationispossibleonlyfora7.1or5.1speakerconguration.
For other speaker congurations, like a 2.1 setup, you have to
manually set them up by referring to the guidelines below for Speaker
Conguration, Speaker Distance and Speaker Levels.
• Thetesttoneemittedduringmeasurementisloud.Thismaybe
bothersome for you and may aect as well your other household
members and even your neighbor.
ABOUT EQUALIZATION
Equalization is one of the parameters automatically adjusted when the
Auto Calibration feature is initiated. If after Auto Calibration, the resulting
equalization eect does not suit your taste or preference, you have the
option to turn o such equalization eect. Below is the procedure on how
to turn o equalization.
1 Ensure that auto calibration is completed. Equalization cannot be
turned ON or OFF if auto calibration is not performed and completed.
2 Using the AVR 4 remote control and with Device Selector set to AMP
page, direct the AVR 4 to the T 748’s remote sensor.
3 Press and hold AVR 4’s [EQ] button until the upper line of the VFD shows
“Adjusting EQ” and the lower line “OFF”; equalization is now turned OFF.
4 If you decide to turn ON again the calibrated equalization eect, press and
hold AVR 4’s [EQ] button until the upper line of the VFD shows “Adjusting
EQ” and the lower line “ON”; equalization is now turned back ON.
It is recommended that you take full advantage of the T 748’s Auto
Calibration feature for your speaker setup. However, if you desire to setup
your speakers manually or if you already had Auto Calibration but would
like to make adjustments, Speaker Conguration, Speaker Levels and
Speaker Distance can be manually set up via their respective setup menu.
OPERATION
USING THE T 748  SETUP MENU
19
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ