Owner's Manual
Table Of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- INTRODUCTION
- IDENTIFICATION OF CONTROLS
- OPERATION
- USING THE T 748 - MAIN MENU
- USING THE T 748 – SETUP MENU
- SETUP MENU
- SOURCE SETUP
- Source Setup (Normal)
- Source Setup (Table)
- iPod SETUP
- Speaker Setup
- AUTO CALIBRATION
- Speaker Configuration
- Speaker Levels
- Speaker Distance
- Adjusting the Volume
- Amplifier Setup
- HDMI setup
- Listening Mode Setup
- Listening Modes
- DOLBY DIGITAL SURROUND MODES
- Dolby Setup
- DTS Setup
- DTS SURROUND MODES
- ENHANCED STEREO
- Display Setup
- A/V Presets SETUP
- AUTO POWER DOWN SETUP
- LISTENING TO AM/FM RADIO
- LISTENING TO DAB RADIO
- OPERATION
- REFERENCE
10 p VOL q
• Increase or decrease loudness level. Release the button when desired level is reached.
• The VFD on the front panel will indicate the level set. For NAD Receivers, the VFD will also show
“Volume Up” or “Volume Down” or “Volume: _ _ dB” (_ _ indicates the numerical dB level) while
pressing AVR 4’s [VOL p/q ] buttons.
11 D/F/A/S, ENTER
Select an item in a menu.
12 SLEEP
Switch o the NAD Receiver or Tuner after a preset number of minutes.
SLEEP MODE
The Sleep Mode timer will switch the T 748 to Standby mode automatically after a preset number of
minutes. Pressing the AVR 4’s [SLEEP] button once will display the current setting of the sleep time
mode or remaining time before the T 748 goes to standby mode. Pressing the AVR 4’s [SLEEP] button a
second time within a 3-second period will change the sleep time mode to the next sleep time setting.
Each consecutive press increases the sleep time in 15-minute increments from 15 to 90 minutes. To
cancel the sleep mode, continue pressing the AVR 4’s [SLEEP] button until “Sleep O” is displayed
on the VFD. Switching the T 748 to standby mode from either the AVR 4’s OFF or the T 748’s Standby
button will also cancel the sleep mode.
13 EQ
Enable or disable Equalization (EQ) eect as set up at Auto Calibration.
14 TONE
Adjust Treble or Bass level. Toggle [TONE] and then use [ D/F ] buttons to set up tone level.
15 L.NITE
Set Dynamic Range Control (DRC) level. Toggle [L.NITE] to select either DTS or Dolby DRC setting
and then use [ D/F ] buttons to set up DRC level.
DVD/BD/CD PLAYER CONTROL USE WITH COMPATIBLE NAD CD PLAYER, BLURAY DISC
PLAYER OR DVD PLAYER MODELS
Set the DEVICE SELECTOR to “BD” in order to gain access to these buttons. Some of the control buttons
below are applicable only to specic NAD CD Player, Blu-ray Disc or DVD Players; check the owner’s
manual of your NAD model for control button compatibility. You can also load the applicable NAD
code library to this device so that it can be made compatible with your other NAD equipment. Refer to
the section below about “LIBRARY” on how to load a NAD code library.
HOME: Display or exit HOME menu.
PICTURE: Display or exit the Picture Mode menu.
TITLE/POP-UP: Display DVD title menu or BD-ROM pop-up menu, if available.
MENU: Access disc menu, if available.
SCAN [ 7/8 ]: Fast reverse/forward search.
[ k ]: Open or close disc tray.
[ g ]: Stop playback.
[ ; ]: Pause playback temporarily.
[ 0 ]: Go to next track, chapter or le.
[ 9 ]: Go to the beginning of current or previous track, chapter or le.
[ 4 ]: Start playback.
ENTER: Select desired track, folder or WMA/MP3 le.
DISP: Show playback time and other display information.
RAND: Play tracks/les in random order.
RPT: Repeat track, chapter, le or whole disc.
PROG: Enter or exit program mode.
CLEAR: Delete programmed track/le.
RES: Set output resolution of HDMI and Component Video output.
SETUP: Access or exit setup menu.
A,B,C,D: Navigate or select BD-ROM menu, if applicable; Page up/down PHOTO and MUSIC menu
list.
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
11
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ