Owner's Manual

INTRODUCTION
GETTING STARTED
UNPACKING AND SETUP
WHAT’S IN THE BOX
Packed with your T 567 you will nd:
• The BR 2 remote control with 2 (two) AA batteries
• A detachable AC power cord
• Set of rubber feet
• This owner’s manual version in CD-ROM
SAVE THE PACKAGING
Please save the box and all of the packaging in which your T 567 arrived.
Should you move or otherwise need to transport your T 567, this is by far
the safest container in which to do so. We’ve seen too many otherwise
perfect components damaged in transit for lack of a proper shipping
carton, so please: Save that box!
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to both
sides and behind), and that will provide a clear line of sight, within 23 feet/7
meters, between the T 567’s front panel and your primary listening/viewing
position. This will ensure reliable infrared remote control communications.
The T 567 generates a modest amount of heat, but nothing that should
trouble adjacent components. It is perfectly possible to stack the T 567 on
top of other components.
DISC LOADING AND PLAYBACK
There are two dierent disc sizes. Place the disc in the correct guide on the
disc tray. If the disc is out of the guide, it may damage the disc and cause
the T 567 to malfunction. “Disc Error” appears at the On-Screen Display
(OSD) (“ERROR” at the VFD), if the disc is placed upside down (and it is a
single sided disc).
The following are important tips when loading a disc:
• Do not push the disc tray while it is moving. Doing so may cause the
T 567 to malfunction.
• Do not push up the disc tray or put any objects other than discs on the
disc tray. Doing so may cause the T 567 to malfunction.
• Keep your ngers well clear of the disc tray as it is closing. Be especially
careful with children’s ngers around the closing disc tray, as there is a
risk of personal injury.
Press [4] (Play), the disc tray is automatically closed. Playback of the rst
track starts if a CD is loaded. For BD, DVD, USB or other disc media, playback
operation is accessible through their menu screen.
NOTE
Do not move the T 567 during playback. Doing so may damage the disc
and the T 567.
ASSEMBLY OF RUBBER FOOT WITH PLASTIC FOOT
QUICK START
In case you simply cannot wait to experience the performance of your new
NAD T 567, we provide the following “Quick Start” instructions to get you
underway.
Please make all the connections to your T 567 with the unit unplugged. It is
also advisable to power-down or unplug all associated components while
making or breaking any signal or AC power connections.
PLAY A BLU-RAY DISC
1 Using a compatible HDMI connector, connect the T 567’s HDMI OUT to
the corresponding HDMI input of your HDMI-compatible TV/monitor.
2 Connect the supplied AC cord to the T 567 AC mains input and then
plug into an AC outlet. Follow the same for your HDMI-compatible TV
as applicable. Switch ON your TV and set it to the HDMI input where the
T 567 is connected.
3 Press the [OPEN/CLOSE] button to switch ON the T 567 and at the same
time open the disc tray.
4 Load the Blu-ray disc in the disc tray.
5 Press the front panel [PLAY/PAUSE] button or [4] (Play) button of
BR 2 remote control to close the disc tray. Depending upon the disc,
playback may commence immediately or you may have to click “Movie”
icon in the “Home Menu” (refer to T 567 default menu screen).
Enjoy the movie but be sure to set aside time to read this manual
thoroughly to set up and congure your T 567 according to your
preference.
Step 1
Insert rubber foot
Squeeze to allow the
rubber foot to clamp under
the six flanges on the
plastic foot
Plastic foot flange
Step 2
Rubber foot inserted
6
ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ