GB Pressur essure High Pr essur e Cleaners ( 110-127 V / 60 Hz ) ( 220-240 V / 50/60 Hz ) ual n a m g in O p e r a t nd conform Read a inst ructions safety use before
Description Dear customer We would like to congratulate you on your new high pressure cleaner with integrated undercarriage and integrated hose drum and to thank you for the purchase. To ease your introduction to the use of the cleaner, we have provided the following pages of explanations, tips and hints, which we ask you to read before using for the first time. The equipment will assist you professionally in all cleaning tasks, e.g.
Description 9 8 3 3 2 7 Water 5 4 3 3 3 6 1 Construction The KRÄNZLE 1120 / 1120 T + 1150 / 1150 T - high pressure cleaners are mobile machines. The design can be seen from the diagram. Item 1 2 3 4 5 Water inlet connection with filter Suction hose with filter (special accessory) Order no. 15.038 3 High pressure pump Press. gauge with glycerin filling Unloader valve - safety valve 6 High pressure injector for cleaning agents 7 High pressure hose 8 Spray gun 9 Interchangeable lance with reg.
Description Water and Cleaning / Pflegemittel System Water can be connected at mains pressure to the high pressure pump or it can be sucked directly from a storage tank. The water is then forced under pressure by the high pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of the lance. Detergent and caring agents can be added through a high pressure injector.Up to max 20m HD hose length.
Description Motor protection switch The motor is protected from overload by a motor protection switch, which automatically cuts out the motor in the event of overload. However should the switch trip frequently, the cause of the malfunction should be located and rectified (see page 6). Replacements and inspection work should only be performed by qualified persons when the machine is disconnected from the power supply, i.e. pull out the plug from the electrical socket.
Description Electrical connection 110 V - 127 V 220 V - 240 V The machine is supplied with an electrical power cord with plug. The mains plug must be fitted to a standard grounded socket with a 30mA residual current operated device. The socket must be protected with a 16A delay action fuse on the mains side.
Description Water connection: Please check that the high pressure cleaner has available the quantity of water specified on page 2 (techn. specs.) (Litres per minute) . 3 3 Test: Allow the water supply hose to run for 1 minute into a bucket.
Description Brief operating instructions When operating your high pressure cleaner pay attention that it is in a horizontal position. 1 . Connect the high pressure hose with spray gun. 2 . Connect to suitable water supply supply.. 3 . Flush the air from the pump (open and close the spray gun several times) 4 . Make the electrical connection 5 . Switch on the machine with opened spray gun and commence cleaning. 6 .
Safety notes As to the recoil see notice on page 2! Apply the safety catch on the spray gun after each use, in order to prevent unintentional spraying! Always aim the underbody lance. Note when using an angled underbody lance, like for example lance No. 41.075 1, that there is a certain amount of torque in the recoil.
This is what you’ve purchased: 1. Dirtkiller with nozzle 045 (at 1120 T and 1150 T) 2. Spray lance with Vario - Jet nozzle 3. Spray gun with insulated pistol grip and screw connection 4. KRÄNZLE - High pressure cleaners 1120 T / 1150 T (50/60 HZ) with hose drum and 15 m high pressure hose with steel reinforcement 5. Crosstip screwdriver 6. Operating instructions Fixing screw for crank 7. Crank for hose drum 8.
How to assemble and furnish your high pressure cleaner Put high pressure cleaner into upright position. Remove the screw from the brass element. Put the crank on the hexagon and fasten with the screw.
Preparation for use 1. Put high pressure cleaner into horizontal position! THE HIGH PRESSURE CLEANER IS ONLY TO BE OPERATED IN HORIZONTAL POSITION ! 2. Connect the high pressure lance to the spray gun. Unroll hose without kinks and connect with handgun and pump. Max. extension 20m-HP hose or 2 x 10m with hose connections. High pressure hose connected to machine and spray gun.
Preparation for use 4 . The machine can be connected to a pressurised water line with 60 60°° C hot water (see page 2). Ensure that the water supply is clean when sucking from external sources. The hose cross section must be at least 1/2" = 12.7 mm (free passage). Filter 1 must always be clean. Please make sure that the filter is clean before using your high pressure cleaner. CAUTION ! When running your high pressure cleaner with hot water of 60°° C raised temperatures occur.
Preparation for use Adjusting the pressure This is accomplished by turning the handwheel. The default setting is maximum pressure. When using cleansing agents: Unwind HP-hose completely. Place chemical filter no. 5 in the reservoir with the cleansing agent. Turn on Vario-Jet No. 4 to to enable the injector to induct the cleansing agent. By turning back the Vario-Jet nozzle, the supply of chemical is automatically cut off. Allow the cleansing agent to take effect and then remove with high pressure spray.
This is prohibited ! Never allow children to use the high pressure cleaner ! Never direct the water jet at the machine itself ! Never direct the water jet at a power socket ! 15
This is prohibited ! Never direct the water jet at people or animals ! Do not damage the power cord or repair it incorrectly ! Never pull the high pressure hose if it has formed kinks or “nooses”! Never pull the hose over sharp edges ! 16
Additional KRÄNZLE-accessories for ... Rotary scrubbing brush Order No. 41.050 1 Drain and pipe cleaning hose 10 m - Order No. 41.058 1 15 m - Order No. 41.058 Underbody lance, new Order No. 41.075 1 Sandblaster Order No. 41.068 1 Flat brush Order No. 41.073 Dirtkiller Order No. 41.
... for further combination possibilities Car cleaning, glass, caravan, boat etc. rotary washing brush with 40 cm extension and ST 30 nipple M 22 x 1,5 Cleaning pipes, channels and drains: pipe cleaning hose with KN nozzle and ST 30 nipple M 22 x 1,5 Underbody cleaning of cars, trailers and equipment: lance 90 cm with high pressure nozzle and ST 30 nipple M 22 x 1,5. The lance must be aimed when spraying.
Small repairs - Do it yourself! You only get a weak flow of water or no water at all! The pressure gauge shows a 10% higher pressure than the working pressure. Now turn on the water and you should get a powerful stream of water The injector may be dirty and you should first remove the hose! But if you only get a weak flow ... release feed line and injector with an openended spanner ..., ... and pull out the injector! Then straighten a paper clip ... Clean the injector thoroughly from both sides ...
Small repairs - The nozzle is blocked! No water but the gauge shows full pressure ! Rinse the hose through first. You should now have a powerful stream of water, remove the lance and clean the nozzle. Insert pointed object into the hole and pull the cap back! Check visually whether the nozzle is clean. 20 but if you only get a few drops from the lance Using the flat spray lance you only have to clean the front nozzle. Straighten a paper clip and clean the nozzle. Now it works as well as before.
- Do it yourself! Nozzle dirty or sticky! Pressure gauge does not show full pressure. Water comes out in spurts. If you do not use the high-pressure cleaner for some time the valves can stick When a valve is blocked, The high-pressure hose vibrates. the gauge shows little pressure or no pressure at all, or the high pressure hose vibrates! and remove the valve screw, the valve and the o-ring. Open the valve with a socket wrench... and remove the dirt from the valve - the valve inside must be closed.
Small repairs - Do it yourself! Stopping leaks from hose or gun After closing the gun the manometer shows full pressure ! The pressure regulator switches on and off contunuously! If the manometer shows full pressure, Pull out the power plug! First disconnect the hose! Press the trigger to release the pressure!!! Clean the return element or replace the O-Ring ! Then unscrew the pump outlet with an open-jew wrench.
Dirtkiller (special accessory) No Description 1 2 3 4 5 6 7 8 9 11 12 Sprühkörper O-Ring 6,88 x 1,68 Düsensitz Düse 045 Stabilisator O-Ring Sprühstopfen Rohr 400 mm 2x M 12 x 1 ST 30-Nippel M 22 x 1,5 / M 12 x 1 ISK Kappe vorn für Schmutzkiller Kappe hinten für Schmutzkiller 045 Qty. Ord.-No 1 1 1 1 1 1 1 1 1 1 1 41.520 41.521 41.522 41.523 41.524 40.016 1 41.526 41.527 13.363 41.528 1 41.540 2 Rep.-kit Dirtkiller 045 consisting of: 1x 2; 3; 4; 5 41.097 Dirtkiller 045 compl. with lance 41.
Gun with lance 24
B A 16 17 18 19 20 21 30 31 32 33 6 7 15 5 No . 12.160 41.156 Midi-Pistole kpl. Lanze kpl. mit Vario-Jet 12.158 13.276 1 13.277 1 13.273 13.363 15.002 13.275 1 41.155 2 41.155 4 41.155 1 41.155 6 50.152 12.144 1 15.004 2 12.125 Ord.-No 12.164 1 1 1 1 1 6 1 1 1 1 1 1 1 1 Qty. Rep.-Kit Pos: 3, 4, 5, 8, 9, 12, 15, 16; 21 Griff komplett Rohranschlußteil R1/4" incl. Pos. 3, 4, 21 Scheibe 5,3 DIN9021 Abzug-Hebel kpl. Rohr kunststoffumspritzt bds.
Complete assembly 26
KRÄNZLE 1120 - 1150 T Spare parts list KRÄNZLE 1120 - 1150T Complete assembly No 1.1 1.2 1.3 1.4 2 3 3.
Motor 28
KRÄNZLE 1120 - 1150 T Spare parts list KRÄNZLE 1120 - 1150 T Motor No Description 1 2 2.1 2.2 3 3.1 3.2 4 5 6 8 9 10 11 12 13 14 15 16 17 18 Ölgehäuse Motorgehäuse mit Stator 230 V / 50 Hz Motorgehäuse mit Stator 110 V / 60 Hz Motorgehäuse mit Stator 230 V / 60 Hz Motorwelle mit Rotor 230 V / 50 Hz Motorwelle mit Rotor 110 V / 60 Hz Motorwelle mit Rotor 230 V / 60 Hz Paßfeder 6 x 6 x 20 Motor-Lager B-Seite Z-Lager Motor-Lager A-Seite Schulterl.
Transmission 30
Gehäuseplatte Öldichtung 14 x 24 x 7 O-Ring 83 x 2 Plungerfeder Federdruckscheibe 14 mm Plunger 14 mm Sprengring 14 mm Taumelscheibe 12,0° für K1120 Taumelscheibe 9,25° für K1150 230V/ 50Hz Taumelscheibe 9,25° für K1150 T 230V/ 50Hz Taumelscheibe 8,0° für K1150 230V/ 60Hz please specifiy angle when ordering Axial-Rillenkugellager 3-teilig Innensechskantschraube M 8 x 25 Verschlußschraube M 18 x 1,5 O-Ring 12 x 2 Ölschauglas Ölverschlußschraube rot Dichtung Öldeckel Deckel Ölgehäuse Innensechskantschraube M
Valve housing K 1120 T - K 1150 T 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Ventilgehäuse Ventilstopfen Ventilstopfen mit R1/4" IG Ventile (rot) Dichtstopfen M 8 x 1 Dichtstopfen M 10 x 1 O-Ring 12 x 2 O-Ring 11 x 1,5 Edelstahlsitz Sicherungsring Edelstahlkugel 8,5 mm Edelstahlfeder Verschlußschraube Steuerkolben 6 mm für AZ Parbaks für Kolben 14 mm Parbaks für Spindel 6 mm MS-Scheibe Kolbenführung 6 mm Mutter M 6 Feder schwarz für AZ-Pumpe Federdruckscheibe Kugellager Handrad M 6 für AZ-Pumpe Mutter
Valve housing K 1120 - K 1150 34
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Ventilgehäuse Ventilstopfen Ventilstopfen mit R1/4" IG Ventile (rot) Dichtstopfen M 8 x 1 Dichtstopfen M 10 x 1 O-Ring 12 x 2 O-Ring 11 x 1,5 Edelstahlsitz Sicherungsring Edelstahlkugel 8,5 mm Edelstahlfeder Verschlußschraube Steuerkolben 6 mm für AZ Parbaks für Kolben 14 mm Parbaks für Spindel 6 mm MS-Scheibe Kolbenführung 6 mm Mutter M 6 Feder schwarz für AZ-Pumpe Federdruckscheibe Kugellager Handrad M 6 für AZ-Pumpe Mutter
Hose drum 36
Description Schale groß Schale klein Knickschutz Antriebswelle Kurbel Lagerklotz links Lagerklotz rechts Drehgelenk Achse mit Wasserführung Eingangsinjektror HD-Schlauch NW 6 15 m Schraube M 6 x 16 Schraube M 5 x 10 Anschlußrohr Ermeto Edelstahl Parbaks 16 mm O-Ring 10 x 2 Sicherungsring 16 mm Scheibe MS 16 x 24 x 2 O-Ring 6,68 x 1,78 Sicherungsring 20 mm Kunststoffschraube 5,0 x 20 Zahnscheibe 6,4 Scheibe DIN9021 6,4 Saugzapfen Schlauchanschluß Edelstahlkugel 5,5 mm Edelstahlfeder Chemikaliensaugschlauch m
Wiring diagram Wiring diagram for KRÄNZLE K 1120 - K1150 T C : 40µF ( 80 µF bei 110V / 60 Hz ) Terminal strip Weber-Unimat WT 22 - 551 13,5A excess current release Motor-Stator 38 braun blau schw rt ge gn ws = = = = = = = brown blue black red yellow green white
General rules Inspections The machine must be inspected according to the “Guidelines for Liquid Spray Devices” at least once every 12 months by a qualified person, to ensure that continued safe operation is guarateed. The results of the inspection are to be recorded in writing. This may be done in any form. Accident prevention The machine is designed for accidents to be impossible if used correctly. The operator is to be notified of the risk of injury from hot machine parts and the high pressure water jet.
