Owner`s manual

SS-900 Rev. A OWNER’S MANUAL
8
MYTEK AMERICA 
Programming Function Programming Method Chirp Light
Code Program (4.1) Turn Ignition On. Within 10 seconds, press program switch
button 4 times then press and hold down program switch button
(1 chirp, 1 light). Press the button #1 of the new transmitter (1
chirp, 1 light). Press the button #1 of the 2
nd
transmitter (1
chirp, 1 light). Press the button #1 of the 3
rd
transmitter (1
chirp, 1 light) and then press the button #1 of the 4
th
transmitter
(1 chirp, 1 light).
1 1
Permanent Siren Chirp
Disable
Permanent Siren Chirp
Enable (4.2)
Turn Ignition on. Within 5 seconds, press and hold the
transmitter button #2 for 5 seconds
1
2
1
2
One Time Soft Chirp
(4.3)
Press and release the transmitter button #2 before other
function buttons.
Shock Sensor Disable
Shock Sensor Enable
(4.4)
Turn ignition on. Within 5 seconds, press and hold the
transmitter button #3 for 5 seconds.
1
2
1
2
Valet Mode On
Valet Mode Off (4.5)
Turn Ignition on. Within 5 seconds, press the program switch
button 2 times. Then within 5 seconds, press and hold the
transmitter button #1 for 5 seconds.
1
2
1
2
Time Start Mode On
Time Start Mode Off
(4.6)
Turn ignition on. Press and hold the program switch button.
Within 10 seconds, press and hold button #1 or #2 for 5
seconds.
1
2
1
2
4.1 Permanent Reprogrammable Factory Code (Code Pre-Programmed By Factory)
When the Dealer installs the unit he programs your unique code which is in permanent memory. Any Authorized
Dealer can add a new or an additional pre-coded transmitter and delete an existing code from memory.
To program a new code:
1. With your vehicle key in key cylinder, turn it to ignition on position (Driving Position).
2. Within 10 seconds, press and release the program switch button four (4) times. Then press and hold down
the program switch button. The program switch is located on the antenna.
3. CODE CHANGE MODE is confirmed with one chirp sound and one parking light flash
4. Within 5 seconds, PRESS AND RELEASE THE BUTTON #1 of the new transmitter. One chirp and one
parking light flash will confirm the acceptance of new code. This operation will erase all previous codes.
5. Within 5 seconds, PRESS AND RELEASE THE BUTTON #1 of the 2
nd
transmitter. One chirp and one
parking light flash will confirm the acceptance of second code.
6. Within 5 seconds, PRESS AND RELEASE THE BUTTON #1 of the 3
rd
transmitter. One chirp and one
parking light flash will confirm the acceptance of third code.
7. Within 5 seconds, PRESS AND RELEASE THE BUTTON #1 of the 4
th
transmitter. One chirp and one
parking light flash will confirm the acceptance of fourth code.
8. Code program will exit when 5 second is passed, when ignition is turned off, when program switch button is
released or when all four codes are programmed.
Note: Module will accept four different transmitters.
4.2 Permanent Siren Chirp Enable/Disable (Factory default setting: Siren Chirp Enable)
Siren chirp can be permanently enabled and disabled from your transmitter.
For PERMANENT SIREN CHIRP DISABLE:
1. With your vehicle key in the key cylinder, turn it to ignition on position (Driving Position).
2. Within five (5) seconds, PRESS AND HOLD THE TRANSMITTER BUTTON #2 for a five (5) seconds.
3. Siren chirp disable is confirmed with one chirp sound and one parking light flash.
1 Chirp1 Light
Flash
Turn Ignition
On
Press PRS
4 Times
Press and
Hold PRS
Press #1