User manual RDRDS20303 Reader HID Mysphera S.L. Parque Tecnológico de Valencia Ronda Auguste y Louis Lumiere, 23 – Nave 13, 46980 Paterna (Valencia) info@mysphera.com www.mysphera.com Telf.: +34 96 182 71 77 / Ext. 112 Fax +34 96 182 94 15 MYSPHERA • Ronda Auguste y Louis Lumiere 23, Nave 13 • 46980 Parque Tecnológico de Valencia • Paterna, Valencia • Spain Telf.: +34 96 182 71 77 • info@mysphera.com • www.mysphera.com Pág.
Modified December 2019 © 2019 Mysphera S.L. ("MYSPHERA") all rights reserved. Any type of exploitation and, in particular, the reproduction, distribution, public communication and / or transformation, in whole or in part, by any means, of this document without the prior express written consent of MYSPHERA is prohibited.
Used simbols in this guide: Simbol Description USB. Electric risk. Warnings: • The product label is located on the bottom of the product. • To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. • Do not place open flame sources, such as burning candles on the product, or in its vicinity. • Do not expose this product to dripping or splashing. • This product must be used indoors. It is not designed or tested for outdoor use.
Contents Contents Contents ........................................................................................................................... 4 Contents ........................................................................................................................... 4 1. Introduction ............................................................................................................ 5 1.1. Package contents .........................................................................
1. Introduction 1.1. Package contents • • Reader HID. USB cable 1.8m-2m. 1.2. Usage requirements • • • USB 2.0 port. Limitated power to 15 W. S.O. Up Windows XP. S.O. Up Linux kernel version 2.4. 2. Product description The Reader HID allows the identification of wristbands easily. Place a bracelet on the reader and it will write its unique identifier on the screen. The Reader HID works like a computer keyboard, so it is not necessary to install any additional software. 2.1.
- - - Product identifier code: o Start with 3 letters indicating type / family of the product. o Followed by 2 letters indicating the type of interface and / or communication of the product. o Followed by 1 digit indicating version of the enclosures / enclosures / mechanical encapsulation. o Followed by 2 digits indicating the hardware version. o Finishing with 2 digits that indicate the firmware version.
4. Intended use To identify a bracelet once the reader is installed, it should only be placed on the cover of the device so that it is close to the antenna, as shown in the following figure. Ilustration 3 – Reader ready (Blue light) Make sure that the cursor on the screen of the computer in which the reader is connected is located in the place you want to write the identifier of the bracelet you wish to identify. The reader works like a keyboard and will write where the cursor is positioned.
In this case, the indicator light will illuminate in red indicating this situation, until the bracelet is removed from above the reader. Ilustration 5 – Reader indicating a bracelet with a low battery (Red light) To avoid unwanted readings, keep the wristbands about 20 cm away from the device. Move the bracelet closer to the device only at the time you wish to read.
5. Maintenance and cleaning No special cleaning products are needed for cleaning this device. Dampen a cloth with water and run it across the surface. Do not immerse or clean the device with pressurized water, as it is not waterproof. Do not clean the equipment when it is turned on. Do not use solvents. This device does not require special maintenance. 6. Storage and devices removal 6.1. Storage • • • • When the wireless gateway is not used, it should be stored in a clean and dry area.
7. Incidents solution 7.1. Usual incidents PROBLEM The reader does not detect a particular bracelet. SOLUTION Try changing the position bracelet and bringing it closer to the antenna. If the bracelet is still not detected, it probably has run out of battery and will have to be replaced. PROBLEM There is no bracelet on the device and it is still locked. SOLUTION Check that there is no bracelet near the reader.
It does not carry an implicit risk for people, animals or objects. The company is not responsible for improper use of it and the possible consequences that the product itself or the parts that form it may have. 8.3. Information about radiofrecuency 8.3.1. Radiolectric devices manufacturing Cuadro Nacional Atribución Frecuencias (Spain, Orden ETU/416/2018, 26th April, 2018) https://www.boe.es/diario_boe/txt.php?id=BOE-A-2018-5704 European Frequency Information System (2402 MHz - 2480 MHz) https://www.efis.
9.3. Updating device The programming and functionality of the hardware and firmware are carried out at the factory complying with the essential requirements of the product. The end user cannot make any modification of the FW / SW or functionality or have any button, connector or element that allows changing any parameter that affects the correct functioning of the product or the fulfillment of its essential requirements.
