User Manual MTBBW10301 Tag Box Mysphera S.L. Parque Tecnológico de Valencia Ronda Auguste y Louis Lumiere, 23 – Nave 13, 46980 Paterna (Valencia) info@mysphera.com www.mysphera.com Telf.: +34 96 182 71 77 / Ext. 112 Fax +34 96 182 94 15 MYSPHERA • Ronda Auguste y Louis Lumiere 23, Nave 13 • 46980 Parque Tecnológico de Valencia • Paterna, Valencia • Spain Telf.: +34 96 182 71 77 • info@mysphera.com • www.mysphera.com Pág.
Modified December 2019 © 2019 Mysphera S.L. ("MYSPHERA") all rights reserved. Any type of exploitation and, in particular, the reproduction, distribution, public communication and / or transformation, in whole or in part, by any means, of this document without the prior express written consent of MYSPHERA is prohibited.
Used simbols in this guide: Simbol Description USB. Electric risk. Warnings: • The product label is located on the bottom of the product. • To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. • Do not place open flame sources, such as burning candles on the product, or in its vicinity. • Do not expose this product to dripping or splashing. • This product must be used indoors. It is not designed or tested for outdoor use.
Contents Contents ........................................................................................................................... 4 1. Introduction ............................................................................................................ 5 1.1. Package contents ............................................................................................... 5 1.2. Usage requirements ...........................................................................................
1. Introduction 1.1. Package contents • • Tag Box. USB cable 1.8m-2m connected inside tag box. 1.2. Usage requirements • • • USB 2.0 port. Limitated power to 15 W S.O. Up Windows XP. S.O. Up Linux kernel version 2.4. 2. Product description The deallocation box is a device designed to be used in conjunction with the MYSPHERA location platform. This box allows you to deallocate all the Tags that are entered into it. Ilustration 1 – Tag Box Consult the deallocation process in the SPHERA Hospital manual.
2.1. Version Product: MTBBW10301 Case : 1.0.0 White structure, transparent drawer with silver knob, turrets, spacers, screws and nylon nuts. Hardware: 3.1.0 Hardware based on SoLA31B BLE with double chip Firmware: 1.0.0 Firmware dual CC2540+CC2541 2.2. Identification Label rear of the device. Ilustration 2 – Identification tag box - - - Product identifier code: o Start with 3 letters indicating type / family of the product.
4. Intended use Deposit the tags through the groove of the upper face or open the drawer and deposit them. Then, close the drawer and in a few seconds, the Tags will have been deactivated on the MYHOSPITAL platform. Ilustración 3 - Tags to deactivate 5. Maintenance and cleaning No special cleaning products are needed for cleaning this device. Dampen a cloth with water and run it across the surface. Do not clean the equipment when it is turned on. Do not use solvents.
6.2. 6.2. Tag Box removal DO NOT OPEN ANY TAG BOX In case of failure or at the end of the use of the wireless gateway, it must be returned to the manufacturer for replacement and / or repair or removal from the market. Contact MYSPHERA before disposing of the wireless gateway. This product should not be treated as household waste.
8.2. Other safety considerations Product not designed or intended for uses other than its installation in stable places and with the ability to detect movement. It does not carry an implicit risk for people, animals or objects. The company is not responsible for improper use of it and the possible consequences that the product itself or the parts that form it may have. 8.3. Information about radiofrecuency 8.3.1.
Changes or modifications not expressly approved by the party responsible for compliance may void the user's authorization to operate the device. 9.3. Updating device The programming and functionality of the hardware and firmware are carried out at the factory complying with the essential requirements of the product.
