Owner`s manual

UPDATING FIRMWARE

To operate with IEX-16L, myMix requires a firmware version of V1.33 or higher, IEX16L-A requires V1.45 or higher. To

operate with myMix CONTROL all devices require 1.51 or higher.

All myMix devices on a network shall always be on the same firmware rev.

Check on www.mymixaudio.com for the latest firmware updates.

Use the external psu for a firmware update. Don‘t connect myMix or the IEX-16L to a switch.

The firmware update requires a temporarily free, in myMix formatted SD /SDHC card compliant to SDA 2.0.*)

Update the myMix unit(s) first (steps 1 through 7), then update the IEX-16L (Steps 8 though 15).

Before you connect to the network ensure all units you want to use have the firmware version.

1. Format SD card in myMix (ADMINISTRATION 8. After myMix has booted up, connect a CAT5

screen) cable to the network port of the unpowered

2. Download the latest firmware for myMix and IEX-16L

IEX-16L from www.mymixaudio.com 9. Go to > Settings >Administration >Update IEX-

3. Save both firmware files (for IEX-16L and 16L firmware and press the encoder wheel

myMix) on the formatted SD card. 10. You'll see a message about the firmware update

4. Insert the SD card in myMix while the unit is taking place.

powered down and not connected to a network(if 11. Now power up the IEX-16L and watch the first 4

you usually use a POE switch to power the unit, LEDs.

please use the external psu). Check for the SD 12. First LED is showing power, the second LED

card symbol in the control bar to show up. If you indicates the IEX-16L is waiting for the software.

still see the “No Card” sign reinsert card. After a few minutes you should see the 3 LED

5. Hold down the MUTE button and the jog wheel, coming up as well. The firmware is now

then power up the unit. transmitted. When the firmware update is ready,

6. Release the two buttons when you see the black the first 4 LEDs will be on permanently.

Firmware Update screen: Updating Firmware. 13. Press soft key “Done” or powercycle myMix.

Be patient while the update is taking place, and 14. Power cycle the IEX16-L

follow the instructions on the screen. Firmware 15. Once the IEX-16L has booted up, go to Settings

updates can take up to 5 minutes. > Remote Devices and press the encoder

7. Reboot your myMix. Check the display for the wheel. You should see the IEX-16L you just

new firmware version in the lower left corner of updated with the new firmware version number.

the splash screen, or go to SETTINGS

>ADMINISTRATION >ABOUT to check the

current firmware version.

Note: a firmware update for myMix or IEX-16L does not clear the initial settings like profiles or preferences. All these settings

remain unaltered.

*) for firmware updates only SD cards up to 16GB are supported.32GB cards work for recording only. Also see:

www.mymixaudio.com/sd-card-information

Troubleshooting for firmware updates

When the myMix unit is powered up with the SD card inserted and under the black screen :

a message “no firmware update file found” shows up:

>SD card not properly inserted, or file corrupt. Insert card again, or replace file

myMix boots as usual, no firmware upadate screen:

>MUTE and Encoder button were not pressed at the same time when unit was powered up, try again.

Updating firmware on IEX-16L and after 5 minutes the 3rd LED hasn‘t come up:

>Can't receive the data from the SD card. Make sure card is inserted correctly and IEX-16L file (.blob) is on

the card and the CAT5 connection to the network port of IEX is good.