Manualshelf

User`s guide

ManualsBrandsMyline Spa ManualsOtherSATURN WM00177
31323334353637383940
Utilities
Start display of string. There is a 2 second delay on each number.
Start display of string. There is a 2 second delay on each number.
Start display of string. There is a slight delay on each number.
These strings will display once
and return to the beginning.
Press Temperature again to
display the string again.
Waiting 10 seconds will allow
the screen to return to
normal operation.
Only if GFCI
is enabled
Only if DEMO Mode
is enabled
To FIRST item in
Main Menu
(TEMP Range)
While the Temperature is
still ashing, press Light
repeatedly until UTIL (Utilities)
appears in the LCD.
SET
RANGE
Main Screen
READY
RANGE
FLTR1
SET
SET
SET
When set to ON, Panel will display
alternate readings from
Senor A and Sensor B
on Main Screen
Back to normal operation
DIP Switch 1 – Test Mode O (0) or On (1)
N/A or Special Amperage Rule 1 or 2
120 or 240 VAC input power
sensed by a
UL system at startup.
3-6 or 1-3 Heater Wattage
as programmed. Displayed by a
CE system at startup.
Heater Type
Displays Fault Log
Displays GFCI Test Menu
OR
DIP Switch 2+3+4 = the number of HS pumps with heat
Store Settings (0) or Memory Reset (1)
DIP Switch
Settings
Waiting
Several Seconds
Reverts to Original Setting
To Set
*****
Several Seconds
OR OR
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel congur
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
See Page 17
See Page 18
Indicates a Menu Item that
Depends on a Manufacturer
Conguration and
may or may not appear.
Adjusting the Set Temperature
When using a panel with Up and Down buttons (Temperature buttons), pressing Up or Down will cause the temperature to
flash. Pressing a temperature button again will adjust the set temperature in the direction indicated on the button. When
the LCD stops flashing, the spa will heat to the new set temperature when required.
If the panel has a single temperature button, pressing the button will cause the temperature to flash. Pressing the button
again will cause the temperature to change in one direction (e.g. UP). After allowing the display to stop flashing, pressing
the Temperature Button will cause the temperature to flash and the next press will change the temperature in the opposite
direction (e.g. DOWN).
Press-and-Hold
If a Temperature button is pressed and held when the temperature is flashing, the temperature will continue to change
until the button is released. If only one temperature button is available and the limit of the Temperature Range is reached
when the button is being held, the progression will reverse direction.
Dual Temperature Ranges
This system incorporates two temperature range settings with independent set temperatures. The High Range designated in
the display by an “up” arrow, and the Low Range designated in the display by a “down” arrow.
These ranges can be used for various reasons, with a common use being a “ready to use” setting vs. a “vacation” setting.
The Ranges ar
e chosen using the menu structure below. Each range maintains its own set temperature as programmed by
the user. This way, when a range is chosen, the spa will heat to the set temperature associated with that range.
For example:
High Range might be set between 80°F and 104°F.
Low Range might be set between 50°F and 99°F.
More specific Temp Ranges may be determined by
the Manufacturer.
Freeze Protection is active in either range.
See Ready and Rest on Page 6
for additional heating control information.
Temperature and Temp Range
High-Range vs.
Low-Range Temp Choice
Press a Temp Button repeatedly to change the temperature.
Pressing and holding a Temp Button will also change the temperature.
Pressing and holding a Temp Button will also change the temperature.
Toggle the Range arrows in the LCD.
SET
RANGE
SET
RANGE
Set Temp will Show & Flash
Set Temp will Show & Flash
SET
RANGE
FLTR
1
SET
RANGE
FLTR
1
SET
RANGE
FLTR1
SET
RANGE
SET
RANGE
Waiting
Several Seconds
Reverts to Original Setting
To Set
*****
SET
RANGE
While
temperature
is ashing...
To next item in Main Menu
Main Screen
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR1
Several Seconds
OR
Main Screen
READY
RANGE
FLTR1
Press a Temp Button repeatedly to change the temperature.
Several Seconds
OR
Main Screen
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR
1
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel
conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original
setting and
ignores any change to that menu item.
*****